Gebruiksaanwijzing /service van het product DVF32TMHST van de fabrikant Desa
Ga naar pagina of 21
This fireplace is manufactured for Stylecrest Inc. under the Coleman brand nam e by DESA International Inc. DESA INTERNATIONAL 2701 INDUSTRIAL DRIVE P/N 56088 P.O. BOX 90024 REV E BOWLING GREEN, KY 42101-9004 10/02 www.desatech.com SAVE THIS BOOK This book is valuable.
- 1 - For more information, visit www.desatech.com CONTENTS 1. INTRODUCTION PG. 2 2. SELECTING LOCATION PG. 2 3. MINIMUM CLEARA NCES PG. 2-3 4. VENT PIPE AND TERM. CLEARANCES PG. 4-5 5. VENTING INSTRUCTIONS PG. 5 6. FRAMING PG. 6 7. GAS SUPPLY TESTING AND HOOK-UP PG.
-2 - For more information, visit www.desatech.com INTRODUCTION Models DVF32TMHST (with fan) and DVF32TMHST-1 (without fan) are heat circulating gravity direct vent gas fireplaces with sealed combusti on cham ber. These fireplaces use a millivolt gas control valv e and millivolt ignition system.
-3 - For more information, visit www.desatech.com MANTEL CLEARANCES Woodwork, such as wood trims, m antels and other combustible ma terials should be placed within the required clearance specified on figures 3 and 4.
-4 - For more information, visit www.desatech.com VENT PIPE AND TERMINATION CLEARANCES The final position of your appl iance depends on the location of th e term ination in relation to the clearances that must be obse rved. A= 12” (305mm ) clearance above grade, veranda, porch, deck or balcony.
-5 - For more information, visit www.desatech.com VENT INSTALLATION INSTRUCTIONS 1. Install pipe to fireplace collar adapter located on back of unit at a 45 deg. Angle. Connect our starting pipe to a 45 deg. Starting section by sliding it over the collar adapter on the fireplace.
-6 - For more information, visit www.desatech.com Refer to the following table fo r clearance between roof and termination. FRAMING Once the final location has been determ ined (observing clearances for vent terminati on), you may construct fram ing using dime nsions shown in figures 10 through 12, dependi ng on the particular installatio n.
-7 - For more information, visit www.desatech.com The remote control receiver is c onnected to the convertible gas valve as shown in figure 14. GAS SUPPLY TESTING NOTE : This section is intended as a guide for quali fied technicians installing g as to the appliance.
-8 - For more information, visit www.desatech.com Install a sediment trap between the incoming gas line and the gas control box (see figure 18). The sedim ent trap should extend down a mini mum of 3 i nches (76 mm) bey ond the center of the pipe.
- 9 - For more information, visit www.desatech.com LOG SET INSTALLATION Before proceeding, make sure th e gas control valve is in the “OFF” position.
- 10 - For more information, visit www.desatech.com 9. Place logs “B” as shown in Figures 25 and 26. Lift the propped up end of log “A” that is propped up and place log “B” under it. At the same time, the ot her side of log “B” is placed over the other log “A”.
- 11 - For more information, visit www.desatech.com BURNER FLAME ADJUSTMENT The air shutter is located at t he underside of the main burner (There are two (2) air shutters on the Propane gas versions). All have been factory preset to the proper ai r-to gas ratio which results in an even, clean burning flame across the burner (See Figure 31).
- 12 - For more information, visit www.desatech.com DECORATIVE FACING Any non-combustible material m ay be used for facing (glass, tile, brick, etc.) as long as the proper clearances are observed (Refer to the section on Clearances). Louvered openings must not be obstructed, and upper a nd lower panels must remai n removable for servicing.
- 13 - For more information, visit www.desatech.com.
- 14 - For more information, visit www.desatech.com ACCESORY AND REPLACEMENT PARTS.
- 15 - For more information, visit www.desatech.com WIRING DIAGRAM.
- 16 - For more information, visit www.desatech.com OBSERVED PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION • Pilot will not stay lit after carefully following ligh ting instructions. • Pilot lit bu t no flame on the burner. • Frequent pilot outage problem.
- 17 - For more information, visit www.desatech.com Read these instructions completely before installing this conversion kit. Before pro ceeding, m ake sure the gas control valve i s on the "OFF" position, all electrical power to the a ppliance is OFF, and the fireplace is cool to the touch.
- 18 - For more information, visit www.desatech.com DISASSEMBLING THE HEARTH AND BURNER SYSTEM 1. Remove the grate with the logs left in place, by lifting th e grate portion off of its stands and place the entire assembly o utside of the unit for ease of reassembly.
- 19 - For more information, visit www.desatech.com REINSTALLING THE MAIN BURNER Reinstall the heart h pan by sliding the end flange over the bo ttom edge of the refractory stand then center and slide the fron t edge down between the raised hearth support.
- 20 - For more information, visit www.desatech.com FINAL PREPARATION 1. Place the grate and log asse mbly back into position on the grate stand as shown in your appliance Installati on Manual. 2. Close the glass door and tightly secure all four l atches.
Een belangrijk punt na aankoop van elk apparaat Desa DVF32TMHST (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Desa DVF32TMHST heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Desa DVF32TMHST vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Desa DVF32TMHST leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Desa DVF32TMHST krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Desa DVF32TMHST bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Desa DVF32TMHST kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Desa DVF32TMHST . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
