Gebruiksaanwijzing /service van het product H3390 van de fabrikant Grizzly
Ga naar pagina of 32
10" WET TILE SAW MODEL H3390 INSTRUCTION MANUAL COPYRIGHT © NOVEMBER 2002 BY GRIZZLY INDUSTRIAL, INC WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemi- cals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints.
TABLE OF CONTENTS PAGE 1. SAFETY ....................................................................................................................... ...............................2 SAFETY RULES FOR TOOLS ..........................................
-2- H3390 Wet Tile Saw SECTION 1: SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.
H3390 Wet Tile Saw -3- 9. USE PROPER EXTENSION CORD . Make sure your extension cord is in good condi- tion. Conductor size must be in accor- dance with the chart below. The amperage rating is listed on the motor or tool name- plate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
-4- H3390 Wet Tile Saw 1. Water Pump . Replace the water pump with a replacement pump from our parts department only. 2. Wet Hands. DO NOT touch connections with wet hands. 3. Plug In. All plug and receptacles should be off the ground and in a dry location.
H3390 Wet Tile Saw -5- SECTION 2: INTRODUCTION We are proud to offer the Grizzly Model H3390 Wet Tile Saw. The Model H3390 is part of a growing Grizzly family of fine woodworking machinery.
-6- H3390 Wet Tile Saw SECTION 3: CIRCUIT REQUIREMENTS 110V Operation The Model H3390 is wired to operate at 110V. A Ground Fault Circuit Interrupter (GFCI) must be used at all times when using this saw. If an outlet is not available that is equipped with a GFCI, use a GFCI plug adapter between the saw power cord and a properly grounded outlet.
H3390 Wet Tile Saw -7- Grounding Extension Cord Reduce the risk of elec- trocution by keeping all connections dry and off the ground. DO NOT touch plugs with wet hands. Failure to follow these warning could result in serious injury. NOTICE The wire on the power cord with green or green and yellow striped insulation is the grounding conductor.
-8- H3390 Wet Tile Saw Clean Up Site Considerations Unsupervised children and visitors entering a shop could receive seri- ous personal injury. Ensure child and visitor safety by keeping all entrances to the shop locked at all times. DO NOT allow unsupervised children or visitors in the shop at any time.
H3390 Wet Tile Saw -9- Main Features C B D A H E F N I J K L M G O Figure 2. Right side of saw. Figure 3. Left side of saw. A. Saw Frame B. Water Reservoir C. Saw Stand D. Water Pump E. Motor F. Blade Guard G. Power Switch H. Water Pump Plug-In I. V-Belt Cover J.
-10- H3390 Wet Tile Saw Assembly Keep clothing rolled up and out of the way of machinery and keep hair pulled back. Wear safety glasses dur- ing the entire assembly process. Failure to com- ply may result in serious personal injury. Disconnect power to the machine when perform- ing any maintenance or assembly.
H3390 Wet Tile Saw -11- 4. Slide the plastic water reservoir into one end of the saw frame as shown in Figure 7 . Be sure the reservoir is not protruding from either end of the frame. Figure 7. Installing the water reservoir. 8. Mount the motor assembly to the frame using (2) M10-1.
-12- H3390 Wet Tile Saw 9. Attach the blade guard to the motor assem- bly using the M8-1.25 x 30 lock knob and M8 flat washer as shown in Figure 11 . Tile saw blades are sold separately. 10. Place the water pump inside the water reser- voir and plug the pump cord into the recepta- cle on the side of the motor assembly.
H3390 Wet Tile Saw -13- 12. Slide the plastic rail end pieces over each of the table rail ends as shown in Figure 15 . 13. Attach the rail/table assembly to the saw frame, using (2) M14-2.0 x 35 hex bolts, (2) M14 flat washers, and (2) M14 external tooth washers as shown in Figure 16 .
-14- H3390 Wet Tile Saw Before starting the machine: 1. Read this manual and make sure you follow all safety precautions before operating this machine. 2. Make sure the blade guard has been cor- rectly installed and is adjusted properly as shown on Page 12 .
H3390 Wet Tile Saw -15- Lubrication To prevent excessive wear on the saw blade, be sure to maintain a continuous flow of water on both sides of the blade. Never cut tile without the water lubrication system running. To set up the water lube system: 1.
-16- H3390 Wet Tile Saw Cut Preparation To prepare for a cut: 1. Fill the water reservoir with water. 2. Plug the saw into the power source. Be sure the cord is positioned with the “drip loop” below the level of the outlet as shown in Figure 18, Page 14 .
H3390 Wet Tile Saw -17- Rip Fence When multiple tiles need to be cut to the same dimension, the rip fence can increase production. Use the scale on the table to set the rip fence to the desired cut.
-18- H3390 Wet Tile Saw SECTION 6: MAINTENANCE General Regular periodic maintenance on your Model H3390 will ensure its optimum performance. Make a habit of inspecting your machine each time you use it. Check for the following conditions and repair or replace when necessary: 1.
H3390 Wet Tile Saw -19- SECTION 7: REFERENCE INFO If you need parts or help in assembling your machine, or if you need operational information, call the Grizzly Service Department.
-20- H3390 Wet Tile Saw Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 MACHINE DATA SHEET Design Type .....................................................................................................
H3390 Wet Tile Saw -21- 48 6 5 4 3 2 1 51 10 8 7 12 9 36 16 11 9 17 37 13 14 15 33 18 19 22 55 54 53 47 44 46 52 45 28 31 32 30 29 26 27 25 56 39 40 38 43 41 42 18 45 48 49 50 24 57 23 58 23 34 35 20 .
-22- H3390 Wet Tile Saw 61 70 65 66 68 67 64 63 62 60 69.
H3390 Wet Tile Saw -23- 36 PH3390036 WHEEL COVER 37 PSB14M CAP SCREW M8-1.25 X 20 38 PH3390038 V-BELT A-680 39 PSB14M CAP SCREW M8-1.25 X 20 40 PH3390040 PULLEY COVER 41 PH3390041 DRIVE PULLEY 42 PK12.
-24- H3390 Wet Tile Saw NOTES.
H3390 Wet Tile Saw -25- NOTES.
-26- H3390 Wet Tile Saw Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
CUT ALONG DOTTED LINE 9. How many of your woodworking machines are Grizzly? _____________ 10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8&qu.
Place Stamp Here FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name_____________________________.
.
Buy Direct and Save with Grizzly ® – Trusted, Proven and a Great Value! -OR- • SECURE ORDERING • ORDERS SHIPPED WITHIN 24 HOURS • E-MAIL RESPONSE WITHIN ONE HOUR Visit Our Website T oday And .
Een belangrijk punt na aankoop van elk apparaat Grizzly H3390 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Grizzly H3390 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Grizzly H3390 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Grizzly H3390 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Grizzly H3390 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Grizzly H3390 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Grizzly H3390 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Grizzly H3390 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
