Gebruiksaanwijzing /service van het product 232L van de fabrikant Husqvarna
Ga naar pagina of 24
225L/LD 225L Lite 232L Read through the Operator‘s Manual carefully and understand the content before using the machine. Operator's manual (CARB, EP A) 101 89 12-95.
2 – English Symbols SYMBOL EXPLANA TION W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can r esult in serious or fatal injury to the operator or others. Read through the O perator‘ s Manual carefully and understand the content before using the machine.
English – 3 Before using a new machine • Read the Operator‘s Manual carefully. • Check the assembly and adjustment of the cutting equipment. See page 13. • Start the machine and check the carburettor settings. See page 16-17. IMPOR T ANT! A too lean carburettor adjustment significantly increases the risk of an engine br eakdown.
4 – English The machine‘s saf ety equipment This section describes the machine‘ s safety equipment, its function and how checks and maintenance ar e carried out to ensure that it operates correctly . (See the chapter “ What is what“ to locate where this equipment is positioned on your machine.
English – 5 SAFETY INSTRUCTIONS 4. Vibration damping system Y our machine is equipped with a vibration damping system, which is designed to give as vibration-free and comfortable use as possible. U se of incorrectly wound cord or incorr ect cutting equipment increases the level of vibration.
6 – English 3. Cutting attachment guard • Ensure that the spray guard is undamaged and is not cracked. • Replace the guard if it has been exposed to impact or is cracked. • Always use the prescribed blade an guard combination, see chapter "Technical data" .
English – 7 SAFETY INSTRUCTIONS 6. Cutting equipment The section describes how through corr ect maintenance and through using the right type of cutting equipment you can: • Obtain maximum clearing capacity. • Increase the service life of the cutting equipment.
8 – English SAFETY INSTRUCTIONS General safety instructions Transport and storage • Store and transport the machine and fuel so that any leakage or fumes do not risk coming into contact with sparks or naked flames. For example, electric machines, electric motors, electrical switches/power switches, heaters or the like.
English – 9 ! General working instructions SAFETY INSTRUCTIONS Basic working techniques • Always trim at full throttle. • Always drop to idling speed after each working operation.
10 – English SAFETY INSTRUCTIONS Clearing • The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the cord strike the ground around trees, posts, statues and the like. NOTE! This technique increases the wear on the cord.
English – 11 26 25 ¥ ¢ 27 = WHA T IS WHA T? What is what on the trimmer? 1. T rimmer head 2. Gr ease filler cap 3. Angle gear 4. Spray guar d 5. Shaft 6. Loop handlebar 7. Throttle 8. Stop switch 9. Throttle trigger lock 10. S uspension for harness (not on 225L Lite) 11.
12 – English Assembling the loop handlebar ASSEMBL Y • Unscrew the handle and plastic cover from the handlebar bracket. • Place the loop handlebar with the handlebar holder on the handlebar bracket. Fit the handle and plastic cover. Do not tighten too tight.
English – 13 ASSEMBL Y K J I G F I M L A K B C • Fit the guard (A) intended for use with the trimmer head. Secure using the 4 bolts (L) and the support plate (M) as set out in the diagram. • Fit the drive disc (B) on the output axle. • Turn the blade axle until one of the holes in the drive disc aligns with the hole in the gear housing.
14 – English FUEL HANDLING Fuel mixture • Clean around the fuel cap. Contamination in the tank can disrupt operations. • Ensure that the fuel is well mixed by shaking the container before filling the tank. W ARNING! Always provide good ventilation when handling fuel.
English – 15 ST ART AND STOP Control before starting F or reasons of safety follo w these recommendations! • Check that the support flange is not cracked due to fatigue or due to being tightened too much. Discard the support flange if it is cracked.
16 – English Carburettor Y our H usqvarna pr oduct has been designed and manufactured to specifications that r educe harmful emissions. After your unit has been run 8-10 tanks of fuel the engine has broken in.
English – 17 Final setting of the idling speed T Adjust the idling speed with the screw T , If it is necessary to readjust. F irst turn the idle speed adjusting screw T clockwise until the cutting attachment starts to rotate/ move. Then turn, counter- clockwise until the cutting attachment stops.
18 – English MAINTENANCE Cooling system T o maintain as low opera- ting temperature as possible the engine is equipped with a cooling system. The cooling system consists of: 1. An air intake on the starter unit. 2. Cooling fins on the flywheel. 3. Cooling fins on the cylinder 4.
English – 19 MAINTENANCE T wo-part shaft The end of the drive axle in the low er shaft should be lubricated with grease every 30 hours. There is a risk that the drive axle ends (splined coupling) on two- part shafts jam if they are not lubricated regularly .
20 – English MAINTENANCE NO TE: Use only HUSQ V ARNA replacement parts. U se of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Y our warranty does not cov er damage or liability caused by the use of accessories and/or attachments not specifically recommended by HUSQ V ARNA.
English – 21 TECHNICAL DA T A T echnical data Engine C ylinder capacity , cu. in/cm 3 C ylinder bore, inch/mm S troke length, inch/mm Recommended max. speed, rpm Max. speed, should not be ex ceeded. rpm I dling speed, rpm S peed of output axle, rpm Max.
22 – English YOUR W ARRANTY RIGHTS AND OBLIGA TIONS The EP A (U.S. Environmental P rotection Agency), Carb (California Air Resources Boar d) and H usqvarna F orest & Garden are pleased to explain the emissions contr ol system warranty on your 1997 and later Lawn and Gar den Equipment Engine.
English – 23 NOTES.
´*2{=¶5A¨.
Een belangrijk punt na aankoop van elk apparaat Husqvarna 232L (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Husqvarna 232L heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Husqvarna 232L vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Husqvarna 232L leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Husqvarna 232L krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Husqvarna 232L bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Husqvarna 232L kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Husqvarna 232L . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
