Gebruiksaanwijzing /service van het product DM-JV600U van de fabrikant JVC
Ga naar pagina of 28
DM-JV600U INSTRUCTIONS HDTV ENCODER For Customer Use: Enter below the Serial No. which is located on the rear of cabinet. Retain this information for future reference. Model No. DM-JV600U Serial No. Thank you for purchasing this JVC product. Before operating this unit, please read the instructions carefully to ensure the best possible performance.
2 1. Read all of these instructions. 2. Save these instructions for later use. 3. All warnings on the product and in the operating instructions should be adhered to. 4. Unplug this appliance system from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
3 SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ATTENTION RISQUE D’ELECTROCUTION NE PAS OUVRIR ATTENTION: POUR EVITER TOUT RISQUE D’ELECTROCUTION NE PAS OUVRIR LE BOITER.
4 Encoded to MPEG-2(ISO/IEC13818-2) Input SMPTE292M(1080i/720p) standard HDTV digital se- rial video signal, encode it to MPEG-2(ISO/IEC13818-2) and output as DVB-ASI TS(Transport Stream).
5 Introduction Preparation Menu setting Basic operation Main Features ...................................... 4 Table of Contents ................................. 5 Precautions .......................................... 6 Front Panel .................
6 Maintenance and operating environment Do not store or use this equipment in the following envi- ronments. This will cause malfunctioning and damage. • Locations beyond the allowable operating temperature range of 5 °C and 40 °C. • Locations beyond the allowable operating humidity level of 30 % and 80 %.
7 Names and Functions 1 [POWER] Power switch Switch to turn on/off power. After this is switched to ON, a “Now Initializing” will be displayed on the Display 5 of front panel before normal screen is displayed. After turning on the power, it may take 2 sec- onds before display light up.
8 8 [AC IN] Power input terminal Use the power cord supplied to connect to an AC 120 V 50 Hz/60 Hz outlet. 9 [HD-SDI IN] Video signal input terminal (BNC) Input terminal for HD serial digital video signal. This terminal also receives audio signal when audio signal is embedded into HD serial digital video signal.
9 Preparation One example of the basic systems using this unit is described below. Turn OFF the power of all devices before connecting or disconnecting.
10 Foot EIA Rack F ront P anel P O W E R O N O F F P O W E R O N O F F Do not remov e the mounting brac ket.The mounting may become unstab le due to loosen screws . In addition, if the mounting direction of the brack et is wrong, it will be e xtremely dangerous as the br ack et will not be properly mounted onto the rack.
11 The menu of this unit consists of 3 level of menus namely “Main menu”, “Sub menu” and “Setting items”. Menu setting Display screen HDTV ENCODER DM-JV600U Main Menu + Configuration Menu .
12 : Default setting Item Setting value Content Operate Param Menu Video Rate Asp 3-2Pulldown Audio Mode Audio Rate Start Stop 9000kbps to 20000kbps to 40000kbps When the Video Mode item i.
13 Item Setting value Content Initial Param Menu Control Mode Start Mode Sync Mode TS Rate Video Mode Audio Format Audio Input Audio ExDelay Audio Enable Local Remote Auto Manual HD-IN REF.
14 Configuration Menu (continued) Item Setting value Content Initial Param Menu PSI Enable P A T TS ID PMT PID PCR PID Video PID Audio PID Video Str eam ID ON OFF 0001 to 0001 to FFFF 0010 to .
15 Configuration Menu (continued) C0 to C0 to DF OFF ON Org Copy OFF ON Org Copy Set the ID of Audio PES stream. Set the copyright flag of Video PES. OFF : Set the copyright flag of Video PES to OFF. ON : Set the copyright flag of Video PES to ON.
16 The various features of this unit can be set using the menu. The setting value, which is stored in the internal memory will reappear upon turning on the power. Example Remote control of this unit can be achieved by using the RS-232C terminal on the rear panel.
17 Basic operation Operation Flow Chart Display Flow Chart Do not turn off the power switch during “Now Initializing” dis- play. Each feature that has been set using the menu can be returned to default (factory setting). All the menu settings return to default.
18 There are 2 ways to start the encoding. One is to start the encoding automatically and the other one is to start it manually by setting the menu. Operation Flow Chart Display Flow Chart The default setting of the Start Mode item is set to “Auto” in order to start the encoding automatically.
19 Basic operation Operation Flow Chart Display Flow Chart Set the Start Mode item in the menu to “Manual” ac- cording to the procedure on ☞ Page 18 “Start the encoding automati- cally”.
20 The operation status of this unit can be confirmed from the display. Operation Flow Chart Display Flow Chart Indicate that the encoding is in process.
21 Basic operation Operation Flow Chart Display Flow Chart The error occurrence can be confirmed on the display. Up to 64 occurrences can be stored. Main Menu +Configuration Menu Main Menu +Status Men.
22 The information regarding built-in program or firmware version can be obtained from the Administration Menu. In addition, clock setting and the display brightness could be adjusted.
23 Basic operation Item Content Model SerNo Time FL Brghtness (Initial Setting: 0) Firm Ucode Boot MISC FPGA STC FPGA I/O PWB I/O VI PLD I/O AU PLD Displays the model name.
24 The stored error log can be displayed by performing the operation on page 21 “Checking Error Log”. The error content is displayed by error code.
25 Others Error code:Error content 0002: parameter error 0008: FAN stop error 0009: FAN stop error recover 001a: FAN stop timeout error 0013: hardware fatal error 0014: software fatal error 0015: syst.
26 It is required to convert the video signal (Pulldown) in order to view the image recorded with 24 frames per second such as movie film on a system for HDTV video signal that is 30 frames per second (60 field) used in TV broadcasting.
27 Video input HD SDI IN × 1 Audio input AES/EBU IN × 1 Synchronized input REF IN × 1 Video output MONITOR OUT × 1 ASI OUT × 2 Dolby™ Digital(AC-3) Pass Through Interface .
DM-JV600U HDTV ENCODER VICTOR COMPANY OF JAPAN, LIMITED is a registered trademark owned b y VICTOR COMP ANY OF JAP AN, L TD . is a registered trademark in Japan, the U .
Een belangrijk punt na aankoop van elk apparaat JVC DM-JV600U (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen JVC DM-JV600U heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens JVC DM-JV600U vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding JVC DM-JV600U leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over JVC DM-JV600U krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van JVC DM-JV600U bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de JVC DM-JV600U kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met JVC DM-JV600U . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
