Gebruiksaanwijzing /service van het product G 1173 SCVi van de fabrikant Miele
Ga naar pagina of 68
Operating instructions for dishwashers To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions as well as the installation plan before it is installed and used for the first time.
Description of the appliance .........................................4 Appliance overview .................................................4 Control panel ......................................................5 Warning and Safety instructions .......
Selecting a programme .............................................3 3 Starting a programme ..............................................3 3 At the end of a programme ..........................................3 4 Switching off .......................
Appliance overview a Upper spray arm (not visible) b Cutlery tray (depending on model) c Upper basket d Middle spray arm e Air inlet for drying (depending on model) f Lower spray arm g Filter combinat.
Control panel a Check/Refill indicators b Programmes c Programme selector button YX d On button U with indicator light e Off button V The symbols are described in greater detail in the relevant sections of these instructions.
This appliance conforms to current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before using it for the first time.
Technical safety ~ Before setting up the appliance, check it for any externally visible damage. Under no circumstances should you use a damaged appliance. A damaged appliance could be dangerous. ~ The dishwasher must only be plugged into the electricity supply via a suitable switched socket.
~ This equipment may only be installed in mobile installations such as ships if a risk assessment of the installation has been carried out by a suitably qualified engineer. ~ The plastic housing of the water connection contains an electrical component.
Installation ~ The dishwasher must be installed and connected in compliance with the installation instructions. ~ The dishwasher must be correctly aligned to ensure problem-free operation. ~ In order to ensure stability, built-under and integrated dishwashers must only be installed under a continuous worktop which is secured to adjacent cabinetry.
~ Inadvertently filling the salt reservoir with powder or liquid dishwasher detergent will damage the water softener. Make sure you have picked up the correct packet of dishwasher salt before filling .
Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of babies and young children.
Energy saving washing This dishwasher is exceptionally economical in its use of water and electricity. You can make the most of your appliance by following these tips: ^ If your household water system is suitable, this dishwasher can be connected to a hot water supply for further economies.
To open the door ^ Pull the handle. If the door is opened during operation all functions are automatically interrupted. To close the door ^ Push the baskets right in.
Water softener In order to achieve good cleaning results, the dishwasher needs to operate with soft water. Hard water results in the build-up of calcium deposits on crockery and in the dishwasher. Mains water with a hardness level higher than 0.7 mmol/l (4 °d – German scale) needs to be softened.
To programme the water hardness level Each time a button is pressed, one of the indicator lights will flash and light up in the control panel. However, only the indicator lights mentioned in the following programming process stages are significant. The programming procedure can be cancelled at any time by pressing the Off button V .
Checking the programmed water hardness level ^ Switch the dishwasher off with the Off button V . ^ Press the programme selector button ;? in, and whilst holding it in switch the dishwasher on using the On button U . Keep the programme selector button ;? pressed in until the lower right hand programme indicator comes on.
Before using the appliance for the first time you require: – approx. 2 litres of water, – approx. 2 kg dishwasher salt*, – domestic dishwasher detergent*, – rinse aid* formulated for domestic dishwashers. Every dishwasher is tested at the factory.
^ Remove the lower basket and unscrew the salt reservoir cap. Only open the salt reservoir when you want to fill it with dishwasher salt as water or salt solution will run out of the reservoir when the cap is removed. ^ Fill the reservoir with approx.
Rinse aid Rinse aid is necessary to ensure water does not cling and leave marks on crockery during the drying phase and helps crockery dry faster after it has been washed. Rinse aid is poured into the storage reservoir and the amount set is dispensed automatically.
^ Add rinse aid only until it is visible in the opening. The rinse aid reservoir holds approx. 110 ml. ^ Close the flap firmly so that it clicks into place. Otherwise water can enter the rinse aid during a programme. ^ Wipe up any spilled rinse aid. This prevents over-foaming occurring during the next programme.
Setting the rinse aid dosage You can adjust the rinse aid dosage for best results. The rinse aid dosage can be set from approx. 0-6 ml. It is set to a recommended setting of approx. 3 ml at the factory. If spots appear on crockery and glassware: ^ Increase the rinse aid dosage.
Note Remove coarse food residues from crockery. There is no need to rinse items under running water. , Do not wash items soiled with ash, sand, wax, lubricating grease or paint in the dishwasher. Ash does not dissolve and is distributed in the wash cabinet.
Items not suitable for dishwashers: – Wooden cutlery and crockery or items with wooden parts: these may discolour and fade. The glue used in these items is not dishwasher-proof and wooden handles may come loose after being washed in a dishwasher.
Upper basket , For safety reasons, do not operate the dishwasher without the upper and lower baskets in place. ^ Use the upper basket for small, lightweight and delicate items such as cups, saucers, glasses, dessert bowls, etc. Shallow pans or casserole dishes can also be placed in the upper basket.
Adjusting the upper basket In order to gain more space for taller pieces of crockery in the bottom or upper basket, the upper basket can be adjusted on three levels with 2 cm between each level. The upper basket can also be set at an angle with one side high and the other side low.
Lower basket ^ For larger and heavier items such as plates, serving platters, saucepans, bowls, etc. Small items such as saucers can also be placed in the lower basket.
Removable spiked insert You can remove the spiked insert to make more room for larger items of crockery, e.g. a large, flat pot, or another type of insert. To remove the insert a ^ Pull it upwards by the handle as shown. To replace the insert b ^ Fit the insert into the lower basket with the hooks going under the long cross-piece as illustrated.
Cutlery Cutlery tray (depending on model) ^ Arrange the cutlery in the tray as shown. To make unloading much easier, cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc.
Cutlery basket (depending on model) ^ To avoid the risk of injury, knives and forks should be placed with the handles upwards in the basket. However, cutlery placed handle down in the basket will come out cleaner and drier. ^ Place small spoons in the individual slots to either side of the cutlery basket.
Detergent , Only use detergents formulated for domestic dishwashers. Do not use washing-up liquid. Active ingredients Modern detergents contain various active ingredients, the most important of which are: – Phosphates to prevent calcification. – Alkalis to aid removal of dried on soiling.
Dispensing ^ Follow the dosage recommended by the manufacturer on the packaging. ^ Unless directed otherwise, use one detergent tab or add 20 to 30 ml detergent in compartment II, depending on the level of soiling. With very heavy soiling you can also add a small amount of detergent to compartment l (see "Programme chart").
Adding detergent ^ Press the opening catch on the detergent dispenser. The flap will spring open. The flap is always open at the end of a programme. ^ Add the required amount of detergent and close the flap. ^ Make sure that the detergent packaging is properly closed after use to avoid it getting damp and becoming lumpy.
Switching on ^ Open the stopcock, if it is closed. ^ Open the door. ^ Make sure the spray arms are not obstructed. ^ Switch the dishwasher on using the On button U . The On indicator light U comes on. Selecting a programme Choose your programme according to the type of load and how dirty it is.
At the end of a programme ^ Open the door slightly to check that the programme has finished. The indicator light next to the programme selected switches off once the programme has finished. If the programme indicator light is still on, the programme has not yet finished.
Interrupting a programme A programme is interrupted as soon as the door is opened. If the door is closed again, the programme will continue from the point it was at before the door was opened. , Water in the dishwasher may be hot. Danger of scalding. Only open the door if absolutely necessary and exercise extreme caution when doing so.
Additional functions Buzzer An audible tone sounds at the end of the programme or if there is a fault. You will hear the buzzer at the end of a programme in bursts of five with a short pause in between. The buzzer will continue to sound for up to an hour if you do not switch the dishwasher off.
Factory default setting If you have altered any settings from the factory default, you can re-set them back to the factory default settings as follows: ^ Open the door. ^ Switch the dishwasher off with the Off button V . ^ Press the programme selector button ;? in, and whilst holding it in switch the dishwasher on using the On button U .
Check your dishwasher regularly (approx. ever y4-6 months). This way faults and problems can be avoided. , The outer surfaces of the dishwasher are susceptible to scratching. Contact with unsuitable cleaning agents can alter or discolour the outer surfaces.
Cleaning the control panel and door front , Remove any soiling immediately. If not, it might become impossible to remove and could cause the outer surface to alter or discolour. ^ The control panel should only be wiped with a damp cloth. ^ Clean the front using a damp cloth or a sponge and a solution of hot water and washing-up liquid.
Cleaning the filters in the wash cabinet The filter combination in the base of the wash cabinet retains coarse soil from the suds solution, preventing it accessing the circulation system and re-entering the cabinet through the spray arms. , The dishwasher must not be used without all the filters in place.
To clean the inside of the filter, the flap must be opened: ^ Press catches a together in the direction of the arrows as shown, and open the filter b . ^ Rinse all the filters under running water. ^ Then close the flap so that the catch engages. ^ Replace the filter combination so that it lies flat in the base of the wash cabinet.
Cleaning the spray arms Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (approx. every 4 - 6 months). ^ Switch the dishwasher off. Remove the spray arms as follows: ^ Take out the cutlery tray (if your dishwasher is fitted with one).
With the aid of the following guide, minor problems can be easily corrected without calling in a Miele service technician, saving you both time and money. , Repairs should only be carried out by a suitably qualified and trained person in strict accordance with current local and national safety regulations.
Problem Possible cause Remedy The buzzer sounds. All the programme indicators flash when the door is opened. There may be a technical fault. Clean the water inlet filter and clean the drain pump and non-return valve as described in “Maintenance”. If this does not resolve the problem, – switch the dishwasher off with the Off button V .
The dishwasher does not fill/drain. Problem Possible cause Remedy The dishwasher stops working shortly after the start of the programme. The buzzer sounds. The Inlet/drain check light 2 / 2 flashes when the door is opened. The stopcock is closed. – Open the stopcock fully.
General problems Problem Possible cause Remedy Detergent residue is left in the dispenser at the end of a programme. The dispenser was still damp when detergent was added. Make sure the dispenser is dry before adding detergent. The detergent dispenser lid cannot be closed properly.
Noises Problem Possible cause Remedy Knocking noise in the wash cabinet. A spray arm is knocking against an item in a basket. Interrupt the programme, and rearrange the items which are obstructing the spray arm. Rattling noise in the wash cabinet. Items of crockery are insecure in the wash cabinet.
Unsatisfactory washing result Problem Possible cause Remedy The dishes are not clean. The dishes were not loaded correctly. See notes in "Loading the dishwasher" The programme was not powerful enough. Select a more intensive programme. See Programme chart.
Problem Possible cause Remedy Dishes, cutlery and glasses are not dry or are flecked. The amount of rinse aid may be insufficient, or the rinse aid reservoir empty. Replenish the reservoir, increase the dosage or change the brand of rinse aid. See "Before using for the first time".
Problem Possible cause Remedy Glassware has a brown or blue tinge, and film cannot be wiped off. This may be caused by the detergent. Change your detergent. Glassware is dull and discoloured; film cannot be wiped off. The glasses are not dishwasher-proof.
Cleaning the water inlet filter A filter is incorporated in the screw connection of the valve on the water inlet hose. The filter must be cleaned when dirty, otherwise insufficient water flows into the wash cabinet. , The plastic housing of the water connection contains an electrical component.
Cleaning the drain pump and non-return valve If the water has not been pumped away at the end of a programme the drain pump or the non-return valve might be blocked. They are, however, easy to clean. ^ Disconnect the dishwasher from the mains supply. Switch off at the mains socket and withdraw the plug.
Test standard: AS/NZS 2007.1:2005, AS/NZS 2007.2:2005; AS/NZS 6400:2005 Standard programme for energy label comparison tests: Normal Capacity: 12/14 place settings (depending on model) Amount of deter.
Model types G 1xxx with a cutlery tray (12 place settings): Upper basket Cutlery tray Lower basket Comparison tests 54.
Model types G 2xxx with a cutlery tray (14 place settings): Upper basket Cutlery tray Lower basket Comparison tests 55.
Programme When to use Sensor wash Sensor controlled programme for normally soiled crockery Normal 1) For normally soiled crockery with dried on soiling; includes glass care system. Quick wash "Quick programme" for lightly soiled crockery, e.
Programme sequence Consumption Duration Energy Water Pre- wash Main wash °C Interim rinse 12 Final rinse °C Drying Cold water connec- tion (20 °C) kWh Hot water connec- tion (60 °C) kWh Litres Cold water connec- tion (20 °C) h:min Hot water connec- tion (60 °C) h:min If required 5 5-6 5 I f required 65 X 1.
Repairs In the event of any faults that you cannot remedy yourself, please contact: – Your Miele Chartered Agent, or – the Miele Service Department (see back cover for address). Please note that telephone calls may be monitored and recorded to improve our service.
To make the most of your dishwasher Optional accessories for particular purposes are available from your Miele Chartered Agent or the Spare Parts Department (some may be supplied as stan - dard, depending on model). If you would like to … you will need to order … … wash long-stemmed glassware … a glassware insert for the upper basket .
, Please follow the installation instructions carefully. All electrical work should be carried out only by a suitably qualified and competent person, in strict accordance with national and local safety regulations. Ensure power is not supplied to the appliance while installation work is being carried out.
The Miele waterproof anti-leak system Providing your dishwasher has been installed correctly, the Miele waterproof anti-leak system will protect you from water damage throughout its lifetime. Connection to the water supply , Water in the dishwasher must not be used as drinking water.
! The inlet hose must not be shortened or damaged in any way as it contains electrical components (see illustration). This appliance incorporates back - flow protection complying with AS/NZS 3500.1.2. No further backflow protection required for connection to the water supply.
Drainage – The appliance drainage system is fitted with a non-return valve, which prevents dirty water from flowing back into the dishwasher via the drain hose. – The dishwasher is supplied with approx. 1.5 m of flexible drain hose with an internal diameter of 22 mm.
Dishwasher model G 1XXX G 2XXX Height 80.5 cm (adjustable + 6.5 cm) 84.5 cm (adjustable + 6.5 cm) Height of building-in recess Min. 80.5 cm (+ 6.5 cm) Min. 84.5 cm (+ 6.5 cm) Width 59.8 cm 59.8 cm Width of building-in recess 60 cm 60 cm Depth 57 cm 57 cm Weight Max.
65.
66.
67.
Alteration rights reserved/ G1173/G2173/ 1608 M.-Nr. 07 223 570 / 00.
Een belangrijk punt na aankoop van elk apparaat Miele G 1173 SCVi (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Miele G 1173 SCVi heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Miele G 1173 SCVi vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Miele G 1173 SCVi leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Miele G 1173 SCVi krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Miele G 1173 SCVi bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Miele G 1173 SCVi kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Miele G 1173 SCVi . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
