Gebruiksaanwijzing /service van het product BT3000 van de fabrikant Ryobi
Ga naar pagina of 14
OPERA T OR'S MANUAL #4950300 ROUTER AND JIG SA W MOUNTING KIT (FOR USE WITH THE BT3000 T ABLE SA W) Save This Manual For Future Reference CONGRATULATIONS AND THANK YOU FOR BUYING THIS RYOBI ROUTER AND JIG SAW MOUNTING KIT . Your new #4950300 Router and Jig Saw Mounting Kit has been designed for use with the RYOBI BT3000 Table Saw.
Page 2 RULES FOR SAFE OPERA TION (Continued) 7. DO NOT MAKE ADJUSTMENTS UNTIL CUTTER OR BLADE HAS COME TO A COMPLETE STOP AND TOOL HAS BEEN DISCONNECTED FROM POWER SOURCE. 8. FEED WORKPIECE AGAINST ROTATION OF CUTTER. 9. DO NOT USE AWKWARD HAND POSITIONS.
Page 3 DESCRIPTION QUANTITY Guide Fence with Guide Block ................................ 2 Knob Bolt (#5/16-18 x 1/2 in.) ................................. 4 5/16" Washer ........................................................... 5 5/16" T-Nut (Special) .
Page 4 ASSEMBL Y Read these instructions completely before beginning assembly of this kit. W ARNING: The saw's motor cord must be disconnected from the receptacle provided on the saw when using this kit with a Router or Jig Saw mounted to the accessory table.
Page 5 ROUTER MOUNTING (Cont'd) TO INSTALL GUIDE FENCE BRACKETS See Figure 4. 1. Align each guide fence bracket with two of the special 5/16 in. T-nuts in channel on top of rip fence. 2. Secure guide fences to rip fence with 5/16 in. washers and 5/16 in.
Page 6 ROUTER MOUNTING (Cont'd) TO ASSEMBLE RE600 ELECTRONIC ROUTER TO ROUTER MOUNTING PLATE See Figures 5 and 6. 1. Remove the subbase screws and subbase from your router. 2. Figure 5 illustrates the correct orientation of parts and pieces for mounting your router to its mounting plate.
Page 7 ROUTER MOUNTING (Cont'd) TO ASSEMBLE TABLE CLAMPING BRACKET (Cont'd) 1. Remove end cap from rear rail as shown in figure 8. 2. Slide one of the special 5/16 in. T-nuts into channel of rear rail. 3. Orient table clamping bracket as shown and secure with a 5/16 in.
Page 8 Fig. 11 Fig. 10 When used for jig saw mounting, this kit can be used with all Ryobi jig saws, plus most other brands of jig saws. Proper mounting of the jig saw base to the clamping brackets will determine which saws will work. The jig saw must be mounted securely for safety.
Page 9 JIG SA W MOUNTING (Cont'd) TO ASSEMBLE MOUNTING PLATE WITH JIG SAW ATTACHED TO ACCESSORY TABLE See Figure 12. 1. Place mounting plate under accessory table as shown in figure 12. Note: If desired you can remove accessory table, attach mounting plate with jig saw, then reassemble complete assembly to your saw.
Page 10 CIRCLE CUTTING JIG CIRCLE CUTTING See Figures 13-16. The circle cutting jig makes it possible to cut and shape circular patterns in both large and small stock. The smallest circle that can be made is approximately 8 in. in diameter. Note: There are many variables that influence the size of a circle being cut or shaped.
Page 11 TO PLACE WORKPIECE ON SAW TABLES See Figure 15. As mentioned previously there are many variables that influence a circle being cut or shaped. These variables must be considered when placing workpiece on saw tables to begin a cut. The sliding miter table and accessory table must both be used when making a cut or shaping.
Page 12 #4950300 ROUTER AND JIG SA W MOUNTING KIT 1 2 3 4 5 5 4 3 6 7 8 9 10 11 12 13 14 15 16 17 18 20 19 4 21 22 24 23 25 3.
Page 13 REPLACEMENT P ARTS Now that you have purchased your Router and Jig Saw Mounting Kit , should a need ever exist for repair parts or service, simply contact your nearest Ryobi Authorized Service Center or other qualified service organization . Be sure to provide all pertinent facts when you call or visit.
R YOBI TECHNOLOGIES INC. 1428 Pearman Dairy Road Anderson SC 29625 Post Office Box 1207 Anderson SC 29622-1207 Phone 1-800-525-2579 612547-852 OPER A T OR'S MANUAL #4950300 ROUTE R AND JIG S A W .
Een belangrijk punt na aankoop van elk apparaat Ryobi BT3000 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Ryobi BT3000 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Ryobi BT3000 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Ryobi BT3000 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Ryobi BT3000 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Ryobi BT3000 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Ryobi BT3000 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Ryobi BT3000 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
