Gebruiksaanwijzing /service van het product RS-1000 van de fabrikant Auto Page
Ga naar pagina of 24
RS1000 OP 1/07 1 RS-1000 OLED PROFESSIONAL OLED 2-WAY 900 MHz. REMOTE CAR STARTER & 6 CHANNEL ALARM SYSTEM With Built-in Temperature Sensor And Serial Port Data Link OPERATION MANUAL Please register your product at: www.
RS1000 OP 1/07 2 OLED REMOTE TRANSCEIVER: A . OLED REMOTE DISPLA Y ……………………………….…..…………………………………..…………………… 4 The Remote Transceiver, XT -100 OLED B. CHARGING THE BATTERY ……….………………………………………………………………………….
RS1000 OP 1/07 3 E. TIMER STA RT …………………………………………….…………….……………………….…..…………………… 19 3 (2 or 1) Hours T imer Start Daily Timer Start Cancel the Timer Start F. TEMPERA TURE CHECK …………….
RS1000 OP 1/07 4 REMOTE TRANSCEIVER (TX) A. OLED DISPLAY B. CHARGE THE BATTERY The unit has a built-in 3.7V lithium polymer battery. If the OLED screen display low battery or the icon is flashing, your remote transceiver needs charging. Please use the included AC / USB charger to charge the battery .
RS1000 OP 1/07 5 AC Pow er Supply: The remote transceiver equipped AC POWER SUPPLY / AC ADAPTOR (Output Voltage: 4.2VDC – 5.5VDC and with same USB plug), then you can charge the battery indoors. This screen w ill be displayed w h ile the battery of the Remote Transceiver is charging.
RS1000 OP 1/07 6 While the icon is flashing. Push the button, the alert alarm time will display ed. Press button 2 to turn OFF the alert alarm timer. D. SELECT THE TRANSCEIVER’S BUTTON CONFIGURATION: 1. Spin the jog shuttle up Switch to select the transceiver button configuration.
RS1000 OP 1/07 7 E- P1- 1. “BUTTON BI” SETTING: Example : Set the “Button Bi Disable” . The unit has a short “bi” sound while pressi ng the buttons of the remote transceiver Spin down the switch to page 1. Press button 1 and it will display the previous setting.
RS1000 OP 1/07 8 E- P1- 4. “DEMO MODE”: To display the units demo mode Spin down the switch to page 1. Press button 4 to start the Demo movie. Demo movie playing. Press any Button to exit. E- P2- 1. “POWER SAVE” SETTING: Example set the “Power Save Enable”.
RS1000 OP 1/07 9 D- P3- 1. “ TIMER / CLOCK” SETTINGS: Example: set the clock to 08:20PM Spin down the switch to page 3. Press button 1 and the ”hours” digit flashes for adjusting. Press button 2 to set the ”hours” digit to “ 08 ”. This can also be done with the jog shuttle.
RS1000 OP 1/07 10 C- P3- 3. “COUNT DOWN TIMER” SETTING: Example: set the count down timer to 2:30 Note: When count down timer is triggered, press any button to stop the beeper. Spin down the switch to page 3. Press button 3 and the ”hours” digit flashes for adjusting.
RS1000 OP 1/07 11 D- P4- 1. “NAME OF TX ” SETTING: Example Set Name of Transceiver 1 to MIKE Spin down the switch to page 4. Press button 1 and the “ - ” flashes for setting. Spin down the switch to set the “ M ”. Press button 1 and the “ - ” flashes for setting.
RS1000 OP 1/07 12 D- P6- 2. SET TO DEFAULTS: Spin down the switch to page 6. Press button 4 . Press buttons 1 & 2 at same time to set the defaults. OPERATION: A. REMOTE TRANSMITTER OPERATION: Transmitter Button System Function Remark 1 Lock Doors & Arm System / Button 1 - Arm and Bypass Zone 4.
RS1000 OP 1/07 13 E. ACTIVE ARMING – LOCK & ARM: 1. Press the button on the transmitter. 2. The siren will chirp once and parking light will flash once indicating that the system is now armed. The vehicle door will lock upon arming when inte rfaced with the security system.
RS1000 OP 1/07 14 SILENT DISARMING: Spin up the switch to the page 1 and then press the “Silent Disarm” button or press the transmitter and buttons at the same time to disa rm your security system, No chirp sound will be heard, arm and disarm confirmation will be through the vehicles parking lights only.
RS1000 OP 1/07 15 transmitter to a parking attendants or a garage mechanic. When the system is in valet mode, all alarm function and remote start functions are bypassed, however the remote panic feature and remote door locks will remain operational. To use the valet mode, the system must first be disarmed.
RS1000 OP 1/07 16 Here’s how the “Noise Abatement Circuit” works: If the alarm triggers five times, each time the same sensor (zone 4) is triggered the “Noise Abatement Circui t” will interpret this pattern of triggers as false alarms.
RS1000 OP 1/07 17 P. DRIVER PAGING / LOST & FOUND This feature is useful in the ev ent that someone wants to page the driv er of the parked vehicle or you cannot find his OLED remote transceiver. Indoor Driving Paging If the ignition switch is in the “off” posit ion, press and hold the valet switch for 2 seconds to page the driver.
RS1000 OP 1/07 18 For 2-w ay OLED Remote Control Transceiv er: A maximum of four vehicle’s security systems can be controlled by this transceiver. TX1 Red Vehicle TX2 Blue Vehicle TX3 Yellow Vehicle.
RS1000 OP 1/07 19 2. Press the brake pedal. Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down. C. TEMPORARY STOP FEATURE: This feature allows the vehicle to remain running a fter the key has been removed from the ignition.
RS1000 OP 1/07 20 F. TEMPERATURE CHECK You can monitor the present indoor tem perature of the passenger compartment through the OLED screen, before coo ling or heating your vehicle. Spin up the switch to the page 4 and then press the “Monitor TEMP.” button; the in-door temperature will be shown on the OLED screen.
RS1000 OP 1/07 21 LIMITED LIFETIME WARRANTY PROVISIONS ( U.S. ,Continental U.S. and C anada Only) 1. Auto Page, Inc. WARRANTS that this new unit has been thoroughly in spected and tested at the factory prior to delivery .
RS1000 OP 1/07 22 Warning: Some batteries may contain Perchlorate What is Perchlorate? Perchlorate is both a naturally occurring and manmade contaminant increasingly found in groundwater, surface water and soil. Most perchlorate manufactured in the U.
RS1000 OP 1/07 23 [ This page left blank inte ntionally ].
RS1000 OP 1/07 24 960 Knox Street Unit B, Torrance, CA 90502 Tel: (310) 323-1800 or (800) 262-2527 www.autopageusa.com.
Een belangrijk punt na aankoop van elk apparaat Auto Page RS-1000 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Auto Page RS-1000 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Auto Page RS-1000 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Auto Page RS-1000 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Auto Page RS-1000 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Auto Page RS-1000 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Auto Page RS-1000 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Auto Page RS-1000 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
