Gebruiksaanwijzing /service van het product 113.24907 van de fabrikant Sears
Ga naar pagina of 28
Save This Manual For Future Reference ISears NODEL NO. 113.249070 Serial Number ......................................... Model and serial number may be found at the right-hand side of the platform channel. You should record both model and serial number in asafe place for future use.
- i = L¸ J JL i FULL ONE YEAR WARRANTY ON CRAFTSMAN COPY-CRAFTER CENTER/DEPARTMENT THROUGHOUT THE UNITED STATES. This warranty gives you specific legal rights, and you may also have other rights wh ch vary from state to state. SEARS, ROEBUCK AND CO., Dept.
19. 20. NEVER STAND ON TOOL Serious injury could occur if the tool is tipped. Do not store materials above or near the tool such that it is necessary to stand on the tool to reach them.
|$ TOOLSNEEDED Pliers Combination Square i/2 in. Wrench The Copy-Crafter is shipped unassembled in one carton "n Make sure that atl of the ftems are removed from the order tofacilitate packaging,.
assembly ROUND HEAD BOLTS AND FLANGE NUTS BED ASSEMBLY The Copy-C;rafter Bed is made up of (3) three Channels held together by T{e Rods. All (3) three Channefs are the same except one has the Copy-Crafter label. This is the Front Channel, The other (2) two are Vertical Channels.
MOUNTING COPY-CRAFTER BED TO LATHE BENCH : • I. Remove _he Too Rest Base and lock ng hardwarefrom the Lathe (see your Lathe Owners Manual) and p ace the Tailstock appr0ximateiy 24 inches from the He.
assembly 7, The Front Charmer should be slightly lower than the top of the Vertical Channels. Check the height with a combination square as shown. If it is higher, loosen the Flange Nuts and lower it. TOOL HOLDER 1. Screw a 1-3/4 inch tong socket head screw tightly into each Knob as shown.
' :' : P_N 3_::: _re_::_he Khobs:and FOilbwer Pins:into the Tool:Post : :::: TOOL POST BASE _/2 INCH SOCKET HEAD SCREW : 6i :An:k!;gnmen_ Gauge is provided to align the tip of the Cutting tl.
assembgy CRADLE CUTTING TOOL C, d. Remove protective coat{ng from the tip of the Cutting Tool and place it in the Cradle, Insert the Cutting Too} and Cradle into the Too] Post and rotate it back and forth whi}e turning the Set Screw in the top of the Too_ Post.
8. CUTTING TOOL I 7. CRADLE 6. TOOL POST / 5. CONTROL KNOBS 4. TO( BASE 3. BRACKETS 9. FOLLOWER PINS 2. VERTICAL CHANNELS t 1. FRONT CHANNEL _ 12_ i 13. CENTER SCREW 10. BED PLATE 1. FRONT CHANNEL...comfortably supports your hands while maneuvering the Cutting Tool.
getting to know your copy-crafter 5, CONTROL KNOBS...provide a comfortable means for maneuvering the Cutting Toot. They are screwed into the holes in the end of the Tool Post for duplicating spindle turnings and: into the opposite ho]es for duplicating faceplate turnings.
11_CLAMP PLATE...holds the Lathe Tool Rest to the Vertical Channels for rough turning to the general sha oe and cleaning up sharp corners on the finished turnings. The toot Rest should be set approximately 1/8 inch below the Centerline Of the Lathe and approximately 1/8 inch away from the workoiece.
getting to know your copy-crafter : 12. SHARPENING STONE...is provided for frequent sharpening of the Cutting Tool REMEMBER THAT WHEN THE TOOL 1S SHARP, HALF OF THE JOB IS DONE, Apply a generous amoun.
11/64 INCH DIAMETER HOLE BACKING / Cut two slots I80 ° apart to fit the tip of the screwdriver_ This will allow you to hold the Faceplate while unscrewing the workpiece. Attach the Backing to the Faceptate with three ##12 or #14x3/4 inca flathead wood screws.
13-114" CENTER LINE HANDLE 1-*--_ 2-314" SOUND BLOCK CENTER LINE I |. t- [ SOUND BLOCK 1 ...... 1-3/4" "I J ,) 1 !132 I CUT WITH SCISSORS ALONG DOTTED LINES Ill-_ z-1/4" m_mm_mmwm/m .-i _CENTER LIN_ !1t32" { 2_ 1 ! ! ] ',_,.
16.
operation DUPLICATING FROM A TEMPLATE Here are instructions for two simpfe projects which wilt familarize you with making templates, and then duplicating from them. STARTER PROJECT: GAVEL AND SOUND BLOCK 1. Remove page 15A from this manual and cut with scissors along dotted lines.
: : Maneuve_ the cutting T0oi b_ moving your wrists while the // /sides Of Your hands _he::Front Channel. Take very light CUts t6 _tar_ With,_ ohtii YOU get the feel Of the cutt ng ._ :action_: :: : : : ...... L_. : :the cutting T001 _houlcl bedown h toward th e narrow diamete_ ! i .
operation 11 _ Turn down both ends to about I/2 inch diameter. 12. Smooth up with sandpaper, 13. Remove the workpiece from the Lathe and cut the ends off. Sand smooth. 14. Select a piece of wood 1-1/4 inches square and t 1-1/4 _nches long for the handle of the gavel.
operaUon 7. Attach Tool Rest (See@ 10 page 11) and turn the workpiece to 4-1/2 inches in diameter. GOUGE 2INCH LONG ROUND HEAD BOLT AND A PLAIN HEXAGON NUT Rotate Tool Post 180 degrees and realign the Cutting Tool with the short Follower Pin...screw Knobs into opposite holes for operation.
operation 10, Insert a screwdriver into one of the slots in the backing to prevent it from turning while unscrewing the workpiece. ! 1. Glue a piece of felt to the bottom to prevent marring the furniture surface, CONE POINT SET SCREW DUPLICATING A SPINDLE FROM AN EXISTING ONE t.
operation turn the Tailstock to the right-hand side of the Lathe bed and replace the: left T_e Rod. Attach a Spindle Bracket to tbe right-hand BraCket: With the C_amp P ate or a piece of plyWood across the Vertical Channels, , ,, align the _'ight-bend cone-Point Set Screw with the point in the Cup center as shown.
operation 9, Use Sears Contour Gauge 9-3946 to obtain the outline of the existing spindfe for the template, CONTOUR GAUGE 23.
repair parts PARTS LIST FOR CRAFTSMAN COPY CRAFTER MODEL 113.249070 s._. 24 2. _ 22 26 Figure 1 20 19 I 16 17 24.
repair parts Key PARTS LIST FOR CRAFTSMAN COPY.CRAFTER MODEL 113.249070 Always Order by Part Number -- Not Key Number FIGURE I No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Part No.
LIST OF PARTS IN LOOSE PARTS BAGS QTY. Loose Parts Bag #70028 _BContaining the following parts:l racket, Right Template ...................... " Rod. 5/16-18 Tie ............................ 2 Bracket. Left Tern plate ....................... Bracket.
27.
SERVICE EL O, 113.249070 HOWTO ORDER REPAIR PARTS Now that you have purchased your Copy-Crafter, should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co. stores. Be sure to provide atl pertinent facts when you call or visit.
Een belangrijk punt na aankoop van elk apparaat Sears 113.24907 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Sears 113.24907 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Sears 113.24907 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Sears 113.24907 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Sears 113.24907 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Sears 113.24907 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Sears 113.24907 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Sears 113.24907 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
