Gebruiksaanwijzing /service van het product 831.159822 van de fabrikant Weider
Ga naar pagina of 32
WEIGHT SYSTEM EXERCISER User ’ s Manual CAUTION Read all precautions and instruc- tions in this manual before using this equipment. Save this manual for future reference. Model No. 831.159822 Serial No. Write the serial number in the space above for reference.
2 IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 1. Read all instructions in this manual and in the accompanying literature before using the weight system. Use the weight system only as described in this manual. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions.
4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 77 in. Width: 81 in. Length: 59 in. Foot Plate Low Pulley Station Ab Pulley Station High Pulley Station Lat Bar Leg Lever Butterfly Arm Press Arm Weight Seat Seat Backrest Backrest Leg Press Plat e Thank you for selecting the versatile WEIDER ® PRO 4100 weight system.
75 5 Before beginning assembly , carefully read the following information and instructions: • Assembly requires two people. • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed.
6 4. Press a 50mm x 63mm Inner Cap (22) into the top of the Right Leg (73). Attach the Right Leg (73) to the Right Base (1) with the two M8 x 65mm Carriage Bolts (57) and two M8 Nylon Locknuts (71). Attach the Right Upright (6) to the Right Base (1) with the two M8 x 70mm Carriage Bolts (102), two M8 W ashers (75), and two M8 Nylon Locknuts (71).
7 7. Set two Weight Bumpers (83) over the indicated holes in the Center Base (67). Insert the two Weight Guides (20) into the holes. Attach the Weight Guides to the Center Base with two M8 x 65mm Bolts (63), four M8 W ashers (75), and two M8 Nylon Locknuts (71).
8 10. Press a 50mm x 63mm Inner Cap (22) into the end of the Right T op Frame (8). Attach the Right T op Frame (8) to the Right Upright (6) with two M8 x 85mm Bolts (59), a Support Plate (21), and two M8 Nylon Locknuts (71).
9 13. Lubricate an M10 x 55mm Bolt (89) with grease. Attach the Pivot Bracket (48) to the Right Butterfly Arm (1 1) with the Bolt and an M10 Nylon Locknut (70). Do not overtighten the Locknut; the Pivot Bracket must be able to pivot easily . Press a 38mm x 50mm Inner Cap (23) into the indicated end of the Right Butterfly Arm (1 1).
10 16. Press a 50mm x 63mm Inner Cap (22) into the top of the Leg Press Frame (30). Lubricate an M10 x 80mm Bolt (61) with grease. Attach the Leg Press Frame (30) to the Left Base (2) with the Bolt and an M10 Nylon Locknut (70). Do not overtighten the Locknut; the Leg Press Frame must be able to pivot easily .
1 1 20. Note: The following drawings are shown from the left side of the weight system, with the Left T op Frame (3) removed for clarity . W rap the High Cable (45) around a 90mm Pulley (38). Attach the Pulley at the rear hole, inside of the bracket on the Center T op Frame (14) with an M10 x 45mm Bolt (66) and an M10 Nylon Locknut (70).
12 23. Locate the Leg Press Cable (95). Attach the Cable inside the Left Leg (36) with an M10 x 70mm Bolt (100), two M10 W ashers (50), two Long Spacers (80), and an M10 Nylon Locknut (70).
13 27. Attach the end of the Leg Press Cable (95) to the “U”-Bracket (85) with an M6 Nylon Locknut (26). Note: Do not completely tighten the Locknut; it should be threaded only two turns onto the end of the Cable, as shown in the inset draw- ing. 28.
14 31. Wrap the Butterfly Cable (46) around a “V”-Pulley (39). Attach the Pulley and a Long Cable T rap (40) to the bracket on the Right Upright (6) with an M10 x 60mm Bolt (65) and an M10 Nylon Locknut (70). Be sure the Cable T rap is turned to hold the Cable in the groove of the Pulley .
15 35. Route the Leg Lever Cable (96) through the Right Upright (6) and under a 90mm Pulley (38). Attach the Pulley inside the Upright with an M10 x 70mm Bolt (100), two M10 W ashers (50), two 13mm Spacers (34), and an M10 Nylon Locknut (70). 36. Wrap the Leg Lever Cable (96) around a 90mm Pulley (38).
16 39. Route the Low Cable (47) through the Left Leg (36) and the Left Upright (7). Attach a 90mm Pulley (38) inside the Upright with an M10 x 70mm Bolt (100), two M10 W ashers (50), two 13mm Spacers (34), and an M10 Nylon Locknut (70). 40. Wrap the Low Cable (47) around a 90mm Pulley (38).
17 41. Wrap the Low Cable (47) around a 90mm Pulley (38). Attach the Pulley to the indicated bracket on the Left Base (2) with an M10 x 45mm Bolt (66) and an M10 Nylon Locknut (70).
18 45. Wrap the Low Cable (47) around a 90mm Pulley (38). Attach the Pulley to the indicated bracket on the Right Base (1) with an M10 x 45mm Bolt (66) and an M10 Nylon Locknut (70).
19 50. Attach a Backrest (15) to the Right Upright (6) with four M6 x 16mm Bolts (13) and four M6 W ashers (35). Repeat this step with the other Backrest (15) and the Left Upright (not shown). 51. Slide the Long Pad T ube (17) through the hole in the Right Leg (73).
20 54. Make sure that all parts have been properly tightened. The use of all remaining parts will be explained in ADJUSTMENTS, starting on the following page. Before using the weight system, pull each cable a few times to make sure that the cables move smoothly over the pulleys.
21 This section explains how to adjust the weight system. See the EXERCISE GUIDELINES on page 26 for impor- tant information about how to get the most benefit from your exercise program. Also, refer to the accompanying exercise guide to see the correct form for each exercise.
22 TIGHTENING THE CABLES W oven cable, the type of cable used on the weight system, can stretch slightly when it is first used. If there is slack in the cables before resistance is felt, the cables should be tightened.
23 WEIGHT RESIST ANCE CHART The chart below shows the approximate weight resistance at each exercise station. “T op” refers to the 6 lb. top weight. The other numbers refer to the 12.5 lb. weight plates. W eight resistance shown for the butterfly arm sta- tion is for each butterfly arm.
High Cable (45) CABLE DIAGRAMS The cable diagrams below show the proper routing of the High Cable (45), the Butterfly Cable (46), the Low Cable (47), the Leg Press Cable (95), and the Leg Lever Cable (96). Use the diagrams to make sure that the cables and the cable traps have been assembled correctly .
25 4 1 2 5 2 1 3 5 Leg Lever Cable (96) Leg Press Cable (95) 3 4 CABLE ID CHART — (46) 47 3/7” — (96) 95 1/2” — (95) 148 1/4” — (47) 276 3/4” — (45) 1 16 3/4”.
26 EXERCISE GUIDELINES THE FOUR BASIC TYPES OF WORKOUTS Muscle Building T o increase the size and strength of your muscles, push them close to their maximum capacity . Y our mus- cles will continually adapt and grow as you progres- sively increase the intensity of your exercise.
27 Rest for a short period of time after each set. The ideal resting periods are: • Rest for three minutes after each set for a muscle building workout. • Rest for one minute after each set for a toning work- out. • Rest for 30 seconds after each set for a weight loss workout.
50mm x 63mm Inner Cap (22) 38mm x 50mm Inner Cap (23) 25mm Round Inner Cap (24) 19mm Round Inner Cap (27) 50mm Square Inner Cap (33) 38mm Square Inner Cap (41) M10 Nylon Locknut (70) M8 Nylon Locknut (71) M6 W asher (35) M8 W asher (75) M4 x 10mm Self- tapping Screw (68) M6 Nylon Locknut (26) M10 W asher (50) P ART IDENTIFICA TION CHART—Model No.
M10 x 60mm Bolt (65) M10 x 80mm Bolt (61) M10 x 95mm Bolt (98) M10 x 65mm Bolt (99) M10 x 50mm Bolt (62) M10 x 45mm Bolt (66) M10 x 70mm Bolt (100) M10 x 100mm Bolt (84) M10 x 135mm Bolt (58) M10 x 80.
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. P ART LIST—Model No. 831.159822 R0103A 1 1 Right Base 2 1 Left Base 3 1 Left T op Frame 4 1 Leg L.
2 7 66 71 81 67 5 6 15 16 34 34 38 39 39 40 41 40 100 90 13 71 71 71 71 71 65 65 70 70 70 75 50 50 35 13 1 28 38 71 66 70 57 71 71 63 71 81 38 47 57 70 102 13 71 38 70 66 21 59 8 22 53 54 54 9 97 97 6.
Part No. 190803 R0103A Printed in China © 2002 Sears, Roebuck and Co. FULL 90 DA Y W ARRANTY For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this .
Een belangrijk punt na aankoop van elk apparaat Weider 831.159822 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Weider 831.159822 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Weider 831.159822 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Weider 831.159822 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Weider 831.159822 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Weider 831.159822 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Weider 831.159822 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Weider 831.159822 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
