Gebruiksaanwijzing /service van het product WESY38321 van de fabrikant Weider
Ga naar pagina of 33
USER'S MANUAL QUESTIONS? As a manufacturer , we are committed to providing complete customer satisfaction. If you have questions, or if parts are missing, we will guarantee com- plete satisfaction through assis- tance from our factory . TO A VOID DELA YS, PLEASE CALL DIRECT TO OUR T OLL- FREE CUSTOMER HOT LINE.
2 T ABLE OF CONTENTS IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORT ANT PRECAUTIONS 3 1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions.
4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 77 in. Width: 81 in. Length: 59 in. Squat Knee Rest Low Pulley Station Lat Bar VKR* Arm *V ertical Knee Raise W eight Pin Adjustment Handle Butterfly A.
5 ASSEMBL Y Make sure that you have the following tools: • T wo adjustable wrenches • One standard screwdriver • One phillips screwdriver • One rubber mallet •Y ou will also need grease or petroleum jelly , a small amount of soapy water , and masking tape.
1. Locate and open the parts bags labeled “FRAME ASSEMBL Y 1” and “FRAME ASSEMBL Y 2.” Press a 2” Square Inner Cap (105) into the open end of the Long Base (120). Insert eight 5/16” x 2 1/2” Carriage Bolts (1 10) up through the Long Base (120) and the Short Base (2) as shown.
4. Press a 1 1/2” Square Inner Cap (67) into the square tube on the Butterfly Upright (3). Slide the Butterfly Upright onto the two indicated 5/16” x 2 1/2” Carriage Bolts (1 10) in the Short Base (2). Finger tighten a 5/16” Nylon Locknut (86) onto each Carriage Bolt.
8 7. Press a 2” x 3” Inner Cap (58) into the top of the Squat Upright (4). Sli de the Squat Upright onto the two indicated 5/16” x 2 1/2” Carriage Bolts (1 10) in the Long Base (120). Finger tighten a 5/16” Nylon Locknut (86) onto each Carriage Bolt.
9 9. Slide the Squat Slider (38) down onto the Squat Upright (4). 10. Insert the ends of two Weight Guides (42) into the indicated bracket on the Long Base (120). Slide two W eight Bumpers (49) onto the Weight Guides. Next, slide ten Weights (44) onto the W eight Guides.
10 14. Press a 2” x 2 1/2” Inner Cap (125) into the Butterfly Frame (47). Attach the tethers on the two “L”-pins (60) to the Butterfly Frame with a #8 x 3/4” Screw (98). Lubricate a 3/8” x 3” Bolt (107) with grease. Attach the Butterfly Frame (47) to the Butterfly T op Frame (7) with the Bolt and a 3/8” Nylon Locknut (87).
19. Locate and open the parts bags labeled “CABLE ASSEMBL Y” and “PULLEYS.” Locate the VKR High Cable (74), which is 82 1/4” long and has an eyelet on one end and a thread- ed bolt on the other end.
12 20. Remove the preattached 3 1/2” Pulleys (78 [only one is shown]) from the Offset Double “U”- bracket (61). W rap the VKR High Cable (74) under a 3 1/2” Pulley (78). Attach the Pulley to the Offset Double “U”-bracket (61) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Locknut (87).
13 24. Route the Lat Cable (88) over a 3 1/2” Pulley (78). Slide a plastic Long Cable T rap (102) onto a 3/8” x 1 3/4” Bolt (93). Attach the Pulley to the indicated bracket on the T op Frame (6) with the Bolt and a 3/8” Nylon Locknut (1 13). Make sure that the Long Cable T rap is turned to hold the Cable in the groove of the Pulley .
14 28. Wrap the Butterfly Cable (69) over a “V”-pulley (55). Attach the Pulley and a Long Cable T rap (102) to the indicated bracket on the Butterfly Upright (3) with a 3/8” x 2 1/2” Bolt (18) and a 3/8” Nylon Locknut (87). Make sure that the Long Cable T rap is turned to hold the Cable in the groove of the Pulley .
15 33 34 35 32. Locate the Leg Lever Cable (75), which is 98 1/2” long and has an eyelet on one end and a thread- ed pin on the other end. Route the eyelet end of the Cable through the Seat Upright (9) and attach it to the tab on the Leg Lever (10) with a 5/16” x 1” Shoulder Bolt (103) and a 5/16” Nylon Locknut (86).
16 36. Remove the preattached 3 1/2” Pulley (not shown) from the “U”-bracket (64). Attach the end of the Leg Lever Cable (75) to the “U”-bracket (64) with a 1/4” W asher (97) and a 1/4” Nylon Locknut (34). Note: Do not completely tighten the Nylon Locknut; it should be thread- ed only two turns onto the end of the Cable.
17 40. Wrap the VKR Low Cable (72) under a 3 1/2” Pulley (78). Attach the Pulley to the indicated brack- et on the Long Base (120) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Locknut (87). 41. Route the VKR Low Cable (72) under the indicated stack of Weights (44).
18 44. Wrap the VKR Low Cable (72) over a 3 1/2” Pulley (78). Attach the Pulley and a Cable T rap (68) between the lower set of holes in the “U”-bracket (64) with a 3/8” x 2” Bolt (100) and a 3/8” Nylon Locknut (87). Make sure that the Cable T rap is turned to hold the Cable in the groove of the Pulley .
19 48. Wrap the Squat Cable (73) under a 3 1/2” Pulley (78). Attach the Pulley to the indicated bracket on the Long Base (120) with a 3/8” x 1 3/4” Bolt (93) and a 3/8” Nylon Locknut (87). 49. Wrap the Squat Cable (73) over a 4 1/2” Pulley (1 19).
20 52. Press two 3/4” x 1 1/2” Inner Caps (1 16) and a 1 1/4” Square Inner Cap (1 17) into the Seat Bracket (1 1). Attach the Seat (16) to the Seat Bracket (1 1) with two 1/4” x 3/4” Screws (1 14), a 1/4” x 1 1/2” Screw (99), and a 1/4” W asher (97).
21 56 57 58 11 4 11 4 12 17 56. Attach the Squat Arm (32) to the Squat Bracket (37) with two 3/8” x 2 1/2” Carriage Bolts (106), two 3/8” W ashers (91), and two 3/8” Nylon Locknuts (87).
22 ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for various exercises.
23 ADJUSTING THE SQUA T ARM, SEA T , OR BUTTERFL Y BACKREST To adjust the height of the Squat Arm (32), first turn the Adjustment Handle (65) on the Squat Bracket (37) counterclockwise several turns to loosen it. Next, pull the Handle and slide the Squat Bracket up or down to the desired position.
24 WEIGHT RESIST ANCE CHART The chart below shows the approximate weight resistance at each weight station. “T op” refers to the 10-pound top weight. The other numbers refer to the 10-pound weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm.
25 TROUBLESHOOTING Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immedi- ately . The weight system can be cleaned using a damp cloth and mild non-abrasive detergent.
26 CABLE DIAGRAMS The cable identification chart below shows the ends of each cable and the lengths of the cables. The cable dia- grams on this page and the following page show the proper routing of the cables. The numbers in the diagrams show the routes of the cables.
27 Leg Lever Cable (75) VKR Low Cable (72) 1 1 3 2 4 5 6 7 9 2 3 4 8.
Cable Clip (83) 3 1/2" Pulley (78) (Not shown to scale) "V" Pulley (55) (Not shown to scale) 4 1/2" Pulley (1 19) (Not shown to scale) 3/8" x 3 3/4" Bolt (122) 3/8" .
3/8" x 2" Bolt (100) 3/8" x 1 3/4" Bolt (93) #10 x 1" Screw (14) 3/8" x 2 1/2" Bolt (18) 5/16" x 2 3/4" Bolt (85) 3/8" x 2 3/4" Bolt (101) 3/8&qu.
1 1/4" Square Inner Cap (1 17) 1" Round Inner Cap (29) 1 1/2" x 2” Inner Cap (21 2" Square Inner Cap (105) 1 1/2" Square Inner Cap (67) 2" x 3” Inner Cap (58) 3/4” .
P ART LIST—Model No. WESY38321 R1 102A Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. 12 1/2” W asher 21 Short Base 31 Butterfly Upright 41 Sq.
4 6 5 7 3 2 8 9 10 11 12 13 15 16 17 109 109 19 19 20 20 21 21 20 20 20 22 21 23 24 25 26 27 27 28 29 29 28 36 36 36 36 30 31 32 33 33 111 111 111 111 35 37 38 39 39 40 40 40 42 42 43 43 46 47 45 44 4.
ORDERING REPLACEMENT P ARTS To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.
Een belangrijk punt na aankoop van elk apparaat Weider WESY38321 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Weider WESY38321 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Weider WESY38321 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Weider WESY38321 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Weider WESY38321 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Weider WESY38321 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Weider WESY38321 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Weider WESY38321 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
