Gebruiksaanwijzing /service van het product 3800 van de fabrikant Chamberlain
Ga naar pagina of 32
Owner’ s Manual ■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The door WILL NOT CLOSE unless The Protector System ® and cable tension monitor are connected and properly aligned.
2 INTRODUCTION Safety Symbol Review and Signal Wor d Review When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury or death if you do not comply with the warnings that accompany them.
Safety Reversing Sensor Safety Reversing Sensor T orsion Spring Motor unit W all-mounted Control Console Access Door Gap between floor and bottom of door must not exceed 1/4" (6 mm). Power Door Lock Cable T ension Monitor Remote Light Drum 3 Planning Survey your garage area to see if any of the conditions below apply to your installation.
4 Preparing your Garage Door Before you begin: • Disable locks. • Remove any ropes connected to garage door . • Complete the following test to make sure your garage door is balanced and is not sticking or binding: 1. Lift the door about halfway as shown.
5 2-Cond u ctor Bell W ire W hite & W hite/Red Safety La b els and Literat u re Remote Control V isor Clip Mo u nting Bracket SECURITY ✚ ® 3-B u tton Remote Control (1) (2) Safety Re v ersing S.
ASSEMBL Y STEP 1 Attach the Collar to the Motor Unit T o avoid installation difficulties, do not run the garage door opener until instructed to do so. • Loosen the collar screws. • Attach collar to either the left or the right side of the motor unit.
7 INST ALLA TION INST ALLA TION STEP 1 Position the Opener 1. Close the garage door completely . 2. Slide the opener with collar over the end of the torsion bar . Check to make sure bracket is located on a solid surface such as wood, concrete or door/flag bracket.
8 Staples Lock Scre w 1/4-20 x 1/2" (2) HARDW ARE SHOWN ACTUAL SIZE Approx. 3" (7.6 cm) Lock T emplate Roller Garage Door T rack TOP DRILL 5/16" DRILL 3/4" DRILL 5/16" 132A250.
9 W HT/GR N T o release w ire, p u sh in ta b w ith scre w dri v er tip Ca b le T ension Monitor 7/16" (1 1mm) Strip w ire 7/16" (1 1mm) W HT/GR N Ca b le T ension Monitor Ca b le T ension M.
10 INST ALLA TION STEP 5 Install the Control Console Locate control console within sight of the door at a minimum height of 5 feet (1.5 m) where small children cannot reach, and away from moving parts of the door and door hardware. The installation surface must be smooth and flat.
11 INST ALLA TION STEP 6 Install Remote Light The remote light is designed to plug directly into a standard 120V outlet. 1. Install the hinge and latch clips. Clips slide in between the metal plate and the plastic housing on each side of the light base (Figure 1).
12 INST ALLA TION STEP 7 Electrical Requirements T o avoid installation difficulties, do not run the opener at this time. T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet.
13 INST ALLA TION STEP 8 Mount the Battery Backup Unit (BBU) (not provided) If the optional 475LM battery backup unit is part of this installation it should be installed at this time. • The BBU can be mounted to either the ceiling or a wall within 3' (.
14 In v isi b le Light Beam Protection Area Safety Re v ersing Sensor 6" (15 cm) max. a b o v e floor Safety Re v ersing Sensor 6" (15 cm) max.
15 DOOR TRACK MOUNT (RIGHT SIDE) Indicator Light Lens Lip Sensor Bracket Door Track FLOOR MOUNT (RIGHT SIDE) WALL MOUNT (RIGHT SIDE) Indicator Light Sensor Bracket Lens Extension Bracket (See Accessor.
16 In v isi b le Light Beam Protection Area S enso r Senso r Safety Re v ersing Sensor Bell W ire Bell W ire Motor u nit Safety Re v ersing Sensor Po w er Door Lock Q u ick-Connect Terminals W HT/BLK .
17 T o prevent damage to vehicles, be sure fully open door provides adequate clearance. WARN ING CAUTION WARN ING WARN ING BLACK PURPLE Push and hold until the door is at desired UP position Figure 2 .
18 ADJUSTMENT STEP 2 Setting the Force The force setting button is located on the front panel. The force setting measures the amount of force required to open and close the door . 1. Locate the purple button on the unit (Figure 1). 2. Push the purple button twice to enter unit into Force Adjustment Mode (Figure 2).
19 ADJUSTMENT STEP 3 T est the Safety Reversal System TEST • With the door fully open, place a 1-1/2" (3.8 cm) board (or a 2x4 laid flat) on the floor , centered under the garage door . • Operate the door in the down direction. The door must reverse on striking the obstruction.
20 ADJUSTMENT STEP 5 T est Cable T ension Monitor If your cable tension monitor has been activated the LED will blink 9 times. ADJUSTMENT STEP 6 T est Power Door Lock TEST • With the door fully closed, the power door lock bolt should be protruding through the track.
21 OPERA TION Using Y our Garage Door Opener Y our LiftMaster Security ✚ ® opener and hand-held remote control have been factory programmed to a matching code which changes with each use, randomly accessing over 100 billion new codes.
22 Using the W all-Mounted Control Console THE MOTION DETECTING CONTROL CONSOLE Press the push bar to open or close the door . Press again to reverse the door during the closing cycle or to stop the door while it's opening.
23 CARE OF YOUR OPENER MAINTENANCE SCHEDULE Once a Month • Manually operate door . If it is unbalanced or binding, call a trained door systems technician. • Check to be sure door opens & closes fully . Adjust limits and/or force if necessary (See Adjustment Steps 1 and 2).
24 Having a Problem? (Continued) 5. The garage door opens and closes by itself: • Be sure that all remote control push buttons are off. • Remove the bell wire from the door control terminals and operate from the remote only .
25 Y our garage door opener is programmed with self- diagnostic capabilities. The “Learn” button/diagnostic LED will flash a number of times then pause signifying it has found a potential issue. Consult Diagnostic Chart below . Diagnostic Char t Symptom: One or both of the Indicator lights on the safety reversing sensors do not glow steady .
26 *3-Button Remote If provided with your garage door opener , the large button is factory programmed to operate it. Additional buttons on any Security ✚ ® 3-Button remote or mini-remote can be programmed to operate other Security ✚ ® garage door openers.
27 1. Enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold ENTER. 2. While holding the ENTER button, press and hold the LIGHT button on the Motion Detecting Control Console.
28 1. Press the “learn button” on light until LED comes ON. 2. Activate the garage door using the hand-held remote, wall control or keyless entry .
29 7 10 11 6 5 NO T IC E 8 1 4 2 3 9 12 L O C K L IG H T 13 14 Installation Parts REP AIR P ARTS KEY P ART NO. NO. DESCRIPTION 1 98LM Motion detecting control panel 2 373W 3-Button remote control 3 10.
30 1 2 3 4 5 6 KEY P ART NO. NO. DESCRIPTION 1 41DJ001 Logic board complete with plate 2 41A61 18 Absolute Encoder System 3 41C168 T ransformer KEY P ART NO.
31 L O C K L I G H T CL OS E D O P E N ACCESSORIES 370LM 41A5281 377LM Extension Brackets: (Optional) For safety reversing sensor installation onto the wall or floor . Keyless Entry with Security ✚ ® : Enables homeowner to operate garage door opener from outside by entering a password on a specially designed keyboard.
LIFTMASTER ® SER VICE IS ON CALL OUR LARGE SERVICE ORGANIZA TION SP ANS AMERICA INST ALLA TION AND SERVICE INFORMA TION IS AS NEAR AS YOUR TELEPHONE SEVEN DA YS A WEEK. SIMPL Y DIAL OUR T OLL FREE NUMBER: 1-800-528-2817 HOURS: (Central Standard Time) 6:00 A.
Een belangrijk punt na aankoop van elk apparaat Chamberlain 3800 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Chamberlain 3800 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Chamberlain 3800 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Chamberlain 3800 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Chamberlain 3800 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Chamberlain 3800 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Chamberlain 3800 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Chamberlain 3800 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
