Gebruiksaanwijzing /service van het product 8200 1/2 HP van de fabrikant Chamberlain
Ga naar pagina of 40
Garage Door Opener Model 8200 Series 1/2 HP For Residential Use Only Owner's Manual ■ Please read this manual and t he enclosed safety materials carefully! ■ Fasten t he manual near the garage door aft er installation. ■ The door WILL NOT CLOSE unless the Prot ector System ® is connected and properly aligned.
Start by reviewing t hese important safety alert symbols 2 Contents Page A review of safety alert symbols ..................................2 You'll need tools ...........................................................3 Safety information regarding garage door locks and ropes .
Pliers Wire Cutters Claw Hammer Hack Saw Screwdriver Adjustable End Wrench 1/2" and 7/16" Sockets and Wrench Drill Tape Measure 2 1 Stepladder Pencil 3/16", 5/16" and 5/32" Dr.
4 Safety Reversing Sensor Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.). See page 24 for details. Support bracket & fastening hardware is required. See page 17.
Safety Reversing Sensor FINISHED CEILING Support bracket & fastening hardware is required. See page 17. Safety Reversing Sensor Header Wall Access Door Gap between floor and bottom of door must not exceed 1/4".
Trolley Header Bracket Hanging Brackets Belt Curved Door Arm Section Straight Door Arm Section Safety Labels and Literature Light Lens (2) Rail Brace (3) T-rail Center Section (each) (2) T-rail End Se.
Lock Washer 5/16" (4) Nut 5/16"-18 (6) Clevis Pin 5/16"x2-3/4" (1) NOTICE Handle Insulated Staples (10) ASSEMBLY INSTALLATION Dry Wall Anchors (2) Clevis Pin 5/16"x1" (1).
8 Assembly St ep 1 Assemble the T -rail & Attach the Belt Pulley Bracket T-RAIL BACK (TO OPENER) T-RAIL FRONT (TO DOOR) Belt pulley bracket attaches to FRONT END of T-rail T-rail (End Section) T-r.
Assembly St ep 2 Install the Trolley on the T -rail 9 • As a temporary stop, insert a screwdriver into the hole in the front end of the T-rail. • Slide the trolley assembly along the rail to the screwdriver stop. If trolley hits against any nuts on the T-rail, the bolts and nuts were attached from the wrong side and must be repositioned.
Assembly St ep 4 Install the Belt & Set the Belt T ension Serious injury can result if fingers become entangled in moving opener sprocket. Attach belt cap retainer securely.
Hex Screws # 8 x 3/8" Belt Cap Retainer Opener Sprocket Mounting Plate Assembly St ep 5 Attach the Belt Cap Retainer IMPORT ANT INST ALLA TION INSTRUCTIONS T o reduce the risk of severe injury or deat h to persons: 1. READ AND FOLLOW ALL INST ALLA TION INSTRUCTIONS.
• Open your door to the highest point of travel as shown. Draw an intersecting horizontal line on the header wall 2" above the high point. This height will provide travel clearance for the top edge of the door. Header Wall Ceiling Track Highest Point of Travel Door 2" 12 Proceed to Step 2, page 14.
Header Wall Vertical Centerline Vertical Centerline of Garage Door 2x4 Unfinished Ceiling Structural Supports 2x4 OPTIONAL CEILING MOUNT FOR HEADER BRACKET • Close the door and mark the inside vertical centerline of your garage door. Extend the line onto the header wall above door.
Lag Screws 5/16"x9x1-5/8" Highest Point of Travel (of Garage Door) Vertical Center Line Header Wall Garage Door UP CEILING MOUNT ONLY Wall Mounting Holes Optional Wall Mounting Holes The nail hole is for positioning only. You must use lag screws to mount the header bracket.
Header Bracket Belt Pulley Bracket Temporary Support Header Wall Garage Door , Liftmaster Synchro Drive Tee Rail to Header Bracket 5/16/92 T-rail Clevis Pin 5/16"x2-3/4 " Ring Fastener Header Bracket Belt Pulley Bracket T-rail • Position the opener on the garage floor below the header bracket.
Installation St ep 4 Position the Opener Follow instructions which apply to your door type as illustrated. To prevent damage to steel, aluminum, fiberglass or glass panel doors, do not rest the opener on the door without using a 2x4.
Installation St ep 5 Hang the Opener Two representative installations are shown. Yours may be different. Hanging brackets should be angled, Figure 1, to provide rigid support. On finished ceilings, Figure 2, attach a sturdy metal bracket to structural supports before installing the opener.
18 Installation St ep 6 Install the Multi-Function Door Control Panel 6ABx1-1/4" Screw Multi-Function Door Control Insulated Staples Dry Wall Anchors Screw 6-32x1" Hardware Shown Actual Size.
• Install a 75 watt maximum light bulb in each socket. The lights will turn ON and remain lit for approximately 4-1/2 minutes when power is connected. Then the lights will turn OFF. • If the bulbs burn out prematurely due to vibration, replace them with "Garage Door Opener" bulbs.
To prevent electrocution, remove power from the garage door opener and from the circuit you plan to use for the permanent connection. To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet.
Without a properly working safety reversing sensor, persons (particularly children) could be injured or killed by a closing garage door. Read and follow all instructions. To protect small children, install the safety reversing sensor so that the beam will be no higher than 4"-6" above the garage floor.
Installation St ep 10 Install the Safety Reversing Sensor 22 FLOOR MOUNT (Right Side) WALL MOUNT (Right Side) DOOR TRACK MOUNT (Right Side) Indicator light Lens Lip Sensor Brack et Door T rac k Sensor.
23 Invisible Light Beam Protection Area Sensor Sensor Connect Wire to Opener Terminals Bell Wire Bell Wire Finished Ceiling OPENER TERMINAL SCREWS Sensor Connections Door Control Connections (dotted l.
Installation St ep 1 1 Fasten Door Bracket Follow instructions which apply to your door type as illustrated below or on page 25. To prevent damage to steel, aluminum, fiberglass or glass panel doors, always reinforce the inside of the door both vertically and horizontally with an angle iron.
Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, aluminum, steel, door with glass panel, etc.). (Not Provided) Header Wall Vertical Centerline of Garage Door .
Ring Fastener Door Bracket Clevis Pin 5/16"x1-1/4" Curved Door Arm Straight Door Arm Clevis Pin 5/16"x1" Lock Washers 5/16" Nuts 5/16"-18 Door Bracket Screws 5/16"-1.
Nuts 5/16"-18 Lock Washers 5/16" Ring Fastener Straight Arm Screws 5/16"-18x7/8 Door Bracket Clevis Pin 5/16"x1-1/4" Curved Door Arm Door Arm Fully Open Trolley Door Arm Conne.
Ad justment Step 1 Adjust the UP and DOWN Limits Do not make any limit adjustments until the Safety Reversing Sensors are completely installed. 28 Limit adjustment settings regulate the points at which the door will stop when moving up or down. The door will stop in the up direction if anything interferes with door travel.
Ad justment Step 2 Adjust the Force Too much force on the door will interfere with the proper operation of the safety reverse system. The door might not reverse properly when required and could seriously injure or kill someone under it. Do not increase the force beyond the minimum amount required to close the door.
Ad justment Step 4 T est the Safety Reverse System Test: • With the door fully open, place a one-inch board (or a 2x4 laid flat) on the floor, centered under the garage door. • Operate the door in the down direction. The door must reverse on striking the obstruction.
Once a Month Manually operate door. If it is unbalanced or binding, call for professional garage door service. Check to be sure door opens and closes fully. Adjust limits and/or force if necessary. (See pages 28 and 29.) Repeat the safety reverse test.
To open the door manually: The door should be fully closed if possible. Pull down on the manual release handle and lift the door manually. To reconnect the door to the opener, press the Door Control push bar.
KG KG 1 3 9 7 5 1 3 9 7 5 1 2 3 Smart (learn) Button SECURITY ✚ Garage Door Opener Indicator Light RIGHT SIDE PANEL KG KG 1 3 9 7 5 1 3 9 7 5 1 2 3 33 Figure 2 SECURITY ✚ Multi-Function Remote Con.
1. Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light, check the fuse box or the circuit breaker. (Some outlets are controlled by a wall switch.) 2. Have you disabled all door locks? Review installation instruction warnings on Page 11.
Having a Problem? (continued) Situation Probable Cause & Solution The opener strains or maximum force is needed to operate the door: The door may be out of balance or the springs are broken. Close the door and use the manual release rope and handle to disconnect the trolley.
9 10 11 NOTICE 5 6 UP CEILING MOUNT ONLY 8 7 4 3 2 1 LOCK LIGHT 13 12 2 1 3 3 4 5 10 5 RAIL GREASE NO. 83A4 8 9 7 6 Repair Parts Rail Assembly Parts Installation Parts 36 KEY PART NO.
Repair Parts Opener Assembly Parts 2 12 10 15 4 3 DN UP Brown Wire (Down) Contact LIMIT SWITCH ASSY. Grey Wire Yellow Wire (Up) Contact Center Limit Contact Drive Gear 11 5 6 7 9 8 9 8 20 14 13 16 1 3 18 19 17 5 KEY PART NO. NO. DESCRIPTION 1 41A4371 Belt cap retainer 2 41A4885-2 Gear and sprocket assy.
Accessories A vailable for your Opener 38 Outside Keylock: Opens the garage door automatically from outside when remote control is not handy. To Add the Keyless Entry We recommend that you program your password before you install the Keyless Entry.
Index Access Door/Outside Quick Release Accessory ............................................................................................4, 5 Electrical Safety Warnings .............................................................................
CHAMBERLAIN SER VICE IS ON CALL OUR LARGE SERVICE ORGANIZATION SPANS AMERICA INSTALLATION AND SERVICE INFORMATION IS AS NEAR AS YOUR TELEPHONE SIX DAYS A WEEK. SIMPLY DIAL OUR TOLL FREE NUMBER: 1-800-528-9131 HOURS: (Central Std. Time) 6 A.M. to 7 P.M.
Een belangrijk punt na aankoop van elk apparaat Chamberlain 8200 1/2 HP (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Chamberlain 8200 1/2 HP heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Chamberlain 8200 1/2 HP vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Chamberlain 8200 1/2 HP leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Chamberlain 8200 1/2 HP krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Chamberlain 8200 1/2 HP bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Chamberlain 8200 1/2 HP kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Chamberlain 8200 1/2 HP . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
