Gebruiksaanwijzing /service van het product EL25 van de fabrikant Chamberlain
Ga naar pagina of 26
Quickstar t EL25 Keypad Pr ogramming Guide EL25 Keypad Pr ogramming Guide T elephone entr y/access control sy stem wit h a 25 direct ory code capacit y ® ™ © 2005 The Chamberlain Group, Inc. All Rights Reser ved Quickstar t This Quickstart Guide is intended to highlight some applications.
Page 1 Programming Number Factory Setting Description of T ask Programming Procedure *** 12 # Enable/Disable T rue Anti-Passback (0 = disable; 1 = enable) # Enable/Disable Timed Anti-Passback (0 = dis.
Page 2 Programming Number 30 30 # (time zone number , 2-63) # (segment number; 99) # (starting time = hhmm; 99) # (ending time = hhmm) # (day of week, 1-8; 1 = Sunday; 7 = Saturday; 8 = holiday) # Cre.
Page 3 Factory Setting Description of T ask Programming Procedure Programming Number 61 # (door 1-4) # (relays to activate 0000-1111) # Order of relay is: relay 4 – relay 3 – relay 2 – relay 1 f.
Page 4 Factory Setting Description of T ask Programming Procedure Programming Number 86 Verify a Card 85 Replace a Card 88 Delete a Card 90 Add a Basic T ransmitter 90 # (transmitter PIN code) # (faci.
Page 5 Factory Setting Description of T ask Programming Procedure Programming Number Verify Multi-Unit Number 111 # 105 Enable or Disable Anti-Passback Forgiveness at Midnight 105 # (0 = disable; 1 = .
Page 6 Programming Basics Programming Single Unit Over view Programming Single Unit Over view 1 1, 2 or 3 digit Programming Number . (See “ Quick Reference Guide ” T ables for descriptions and procedures) 2 One or more Data Fields . 3 Pound Key ( # ) as a Data Field Separator and at the end of the programming sequence to Save the Data .
Page 7 Enter Programming Mode Exit Programming Mode 1 Press 2 Enter the ( 6 ) six-digit password. The default is six zeroes. If you will be programming the unit via modem, please refer to the V ersa XS online help. After entering programming mode for the first time, we suggest you change the password to maintain the security of your system.
Page 8 System Feedback / Responses (Beeps) 2 Short Beeps: Programming step was valid. 3 Short Beeps: Programming mode was exited. 1 Long Beep: Input was not valid. 2 Long Beeps: Duplicate entry code was entered. 3 Long Beeps: Memory is full. 4 Long Beeps: Unit has reset or is powering up.
Page 9 Programming Multiple Units Over view Note: Yo u cannot program a unit within a multi-unit chain from a local/remote DTMF phone (T ouch-T one) unless you know the unit's ID number . Therefore, you can only verify the unit number while programming from the unit's front keypad.
Page 10 Getting Started EL25 SetUp “Y our Settings” Change the unit password to prevent any tampering with your system's database. When changing the password, save a copy of it in a secure location. If you lose the password, you will not be able to enter into programming mode.
Page 11 A relay is a device that reacts to an electric current to activate other devices. Allowing the EL25 to lock or unlock a door/gate, shunt (bypass) alarm contacts, signal an alarm, or turn on a camera wired to a closed-circuit television (CCTV).
Page 12 T o perform these 4 steps you MUST know EXACTL Y where the External Access Control Device(s) were wired in “Y our” EL25! When the table on page 14 is completed by you or your installer , this will help you understand “Y our” personal layout.
Page 13 1 Press 2 Enter the Relay Number (1-4). Then ( # ) 3 Enter Activation Time (1-300 Seconds). Then ( # ) Then 1 Press 2 Enter Door Number (1-4). Then ( # ) 3 Enter Relays to be Activated (0000-1111).
Page 14 Sample: EL25 Controlling 1 Door (Page 16) EL25 SetUp “Y our Settings” EL25 SetUp “Y our Settings” When “ Y our Door Settings ” or “ Door 1,2,3 or 4 ” are referenced throughout this guide, this completed chart will outline how your EL25 system will function.
Page 15 How your system has been wired is an important part of programming it. Write down your configuration. T o help visualize it, draw a map of it below .
Page 16 EL25 SetUp “Y our Settings” EL25 SetUp “Y our Settings” Relay 1 - Strike Mode Unlocks Door for 10 sec. Relay 2 - Control Mode T urns on Security Light for 60 sec. Relay 3 - Alarm Mode Sounds Siren for 10 sec. Relay 2 - Shunt Mode Bypasses/Signals Alarm for Maglock for 40 sec.
Page 17 EL25 SetUp “Y our Settings” EL25 SetUp “Y our Settings” EL25 Main Keypad (Front Door) Wiegand Keypad (Exit) Card Reader (Back Door) Card Reader (Manager's Door) EL25 Controlling 4 Doors Relay 1 - Strike Mode Unlocks Door for 10 sec.
Page 18 Location Door No. Relay Relay Mode Relay Function Relay Activation Time (Seconds) Driveway Pedestrian Gate In EL25 1 Strike Opens Vehicular Gate 10 sec. 2 Control T urns on Security Light 10 sec. Device Main Keypad and (REX) Exit Request CCTV Wiegand Card Reader Door 1 Door 2 Door 3 3 Strike Unlocks Pedestrian Gate 10 sec.
Page 19 Location Relay Relay Mode Relay Function Relay Activation Time (Seconds) Front Door (Entrance) Vehicular Gate Pool Gate Front Door (Entrance) 1 Strike Unlocks Door 10 sec. 2 Strike Unlocks Door 10 sec. Device Main Keypad T ransmitter and REX Exit Device Wiegand Card Reader Siren Door 1 Door 2 Door 3 Door 4 3 Strike Unlocks Door 10 sec.
Page 20 Entr y Codes Access Cards 1 Press 2 Enter Entry Code (3-9 digits). Then ( # ) Factory Setting for Entr y Code Length is 4 digits See “Entry Code Length” above. Add an Entr y Code ONL Y . For adding or editing full function Entry Codes (i.e.
Page 21 Transmitters 1 Press 2 Enter T ransmitter Number (1-65534). Then ( # ) Add a Basic transmitter to the system's database. A basic transmitter will be active, unlock all doors/gates assigned to the RF module with no time constraints (i.e., can be used 24 hours a day , 7 days a week.
Page 22 Appendix Appendix Quick Reference Guide Glossary Appendix Glossar y Glossar y Glossar y Glossar y Glossar y Glossar y Access Device (RF Receiver , Card Reader , or Keypad) - A device that reads transmitter , card or entry codes, allowing the system to allow or reject entry based on the code's validity .
Page 23 Appendix Appendix Quick Reference Guide Glossary Appendix Gate or Door - Used synonymously throughout the manual, these terms refer to controllable entry/exit areas of the complex, normally a gate or door . Holiday Schedules - Holiday schedules will modify fixed schedules for selected holiday dates.
Page 24 Appendix Appendix Appendix Appendix Access Cards Direct Commands Entry Codes Programming – Enter Program Mode – Exit Program Mode – Multiple Units – Single Unit Quick Reference Guide Q.
© 2005 The Chamberlain Group, Inc. All Rights Reser ved 114A3042 845 Lar ch Avenue Elmhurst, Illinois 60125-1196 ® ™.
Een belangrijk punt na aankoop van elk apparaat Chamberlain EL25 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Chamberlain EL25 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Chamberlain EL25 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Chamberlain EL25 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Chamberlain EL25 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Chamberlain EL25 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Chamberlain EL25 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Chamberlain EL25 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
