Gebruiksaanwijzing /service van het product 2010 Avalanche van de fabrikant Chevrolet
Ga naar pagina of 582
2010 Chevrolet A valanche Owner Manual M In Brief ................ .......... ........... ....... 1 - 1 I n s t r u m e n t P a n e l ... .............................. 1 - 2 Initial Drive Information . . . . . . . . . . . . . . . . . . . . . . . . . .
2010 Chevrolet A valanche Owner Manual M F r o n t A x l e ....................................... 6 - 4 7 H e a d l a m p A i m i n g ............................... 6 - 4 8 B u l b R e p l a c e m e n t ... ........................... 6 - 5 0 Windshield Wiper Blade Replacement .
GENERAL MOTORS, GM, the GM Emblem, CHEVROLET , the CHEVROLET Emblem, and the names A V ALANCHE and Z71 are registered trademarks of General Motors. This manual describes features that may or may not be on your specific vehicle either because they are options that you did not purchase or due to changes subsequent to the printing of this owner manual.
Safety W arnings and Symbols W arning messages found on vehicle labels and in this manual describe hazards and what to do to avoid or reduce them. Danger indicates a hazard with a high level of risk which will result in serious injury or death. W arning or Caution indicates a hazard that could result in injury or death.
V ehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index. 0 : Adjustable Pedals 9 : Airbag Readiness Light # : Air Conditioning ! : Antilock Brake System (ABS) g : Audio Steering Wheel Controls or OnStar ® $ : Brake System Warning Light " : Charging System I : Cruise Control B : Engine Coolant T emperature O : Exterior Lamps # : Fog Lamps .
2 NOTES vi.
Section 1 In Brief Instrument Panel .................................. . 1-2 Initial Drive Information .. ................ ......... 1-4 Remote Keyless Entry (RKE) System . . . . . . . . . . . 1-4 Remote V ehicle Start . . . . . . . . . . . . . . . . .
Instrument Panel 1-2.
A. Outlet Adjustment on page 4 ‑ 25 . B. T urn Signal/Multifunction Lever on page 4 ‑ 4 . C. Instrument Panel Cluster on page 4 ‑ 26 . D. Hazard Warning Flashers on page 4 ‑ 3 . E. Shift Lever . See Automatic T ransmission Operation on page 3 ‑ 37 .
Initial Drive Information This section provides a brief overview about some of the important features that may or may not be on your specific vehicle. For more detailed information, refer to each of the features which can be found later in this owner manual.
Remote V ehicle Start With this feature the engine can be started from outside of the vehicle. Starting the V ehicle 1. Aim the RKE transmitter at the vehicle. 2. Press Q . 3. Immediately after completing Step 2, press and hold / until the turn signal lamps flash.
Midgate ® This vehicle is equipped with a Midgate ® and a removable rear glass panel. The Midgate allows you to extend the length of the vehicle's cargo area. For more information see Midgate ® on page 3 ‑ 13 . T ailgate Use the Remote Keyless Entry (RKE) transmitter or power door lock switch to lock and unlock the tailgate.
Seat Adjustment Front Seats Manual Seats If the vehicle has a manual seat, it can be moved forward or rearward. 1. Lift the bar to unlock the seat. 2. Slide the seat to the desired position and release the bar . T ry to move the seat with your body to be sure the seat is locked in place.
Manual Lumbar If equipped, this control is located on the outboard side of the seat. Increase or decrease lumbar support by turning the knob forward or rearward. Power Lumbar If equipped, this control is located on the outboard side of the seat. On vehicles with two-way lumbar , press and hold the top of the control to increase lumbar support.
Manual Reclining Seatbacks If equipped, this control is located on the outboard side of the seat. T o recline the seatback: 1. Lift the recline lever . 2. Move the seatback to the desired position, then release the lever to lock the seatback in place.
Memory Features This vehicle may have the memory package. The controls for this feature are located on the driver door , and are used to program and recall memory settings for the driver seat, outside mirrors, and the adjustable throttle and brake pedal feature.
Safety Belt Refer to the following sections for important information on how to use safety belts properly . . Safety Belts: They Are for Everyone on page 2 ‑ 15 . . How to Wear Safety Belts Properly on page 2 ‑ 20 . . Lap-Shoulder Belt on page 2 ‑ 29 .
Mirror Adjustment Exterior Mirrors V ehicles with outside power mirrors and foldaway mirrors have controls located on the driver door . 1. Press (A) or (B) to select the driver or passenger side mirror . 2. Press one of the four arrows located on the control pad to adjust the mirror .
Steering Wheel Adjustment The tilt lever is located on the lower left side of the steering column. T o adjust the steering wheel: 1. Hold the steering wheel and pull the lever . 2. Move the steering wheel to a comfortable position. 3. Release the lever to lock the wheel in place.
Interior Lighting Dome Lamps The dome lamps come on when any door is opened. They turn off after all the doors are closed. The dome lamps can also be turned on by turning the instrument panel brightness knob, located on the instrument panel to the left of the steering column, clockwise to the farthest position.
Exterior Lighting The exterior lamps control is located on the instrument panel to the left of the steering wheel. 9 (Off): Turns off the automatic headlamps and daytime running lamps (DRL). Turn the headlamp control to the off position again to turn the automatic headlamps or DRL back on.
Climate Controls The heating, cooling, defrost, defog and ventilation of the vehicle can be controlled with these systems. A. Fan Control B. Outside Air C. Air Recirculation D. Air Delivery Mode Control E. Air Conditioning F . Driver and Passenger T emperature Controls G.
V ehicle Features Radio(s) Radio with CD, DVD, and USB Port O : Press to turn the system on and off. Turn to increase or decrease the volume. BAND : Press to choose between FM, AM, or XM ™ , if equipped. f : Select radio stations. © ¨ : Seek or scan stations.
Setting the Clock T o set the time and date for the radio with CD, DVD, and USB Port: 1. T urn the ignition key to ACC/ACCESSORY or ON/RUN, then press O , to turn the radio on. 2. Press G to display HR, MIN, MM, DD, YYYY (hour , minute, month, day , and year).
Steering Wheel Controls For vehicles with audio steering wheel controls, some audio controls can be adjusted at the steering wheel. w / x : Press to change favorite radio stations, select tracks on a CD/DVD, or to navigate tracks or folders on an iPod ® or USB device.
Driver Information Center (DIC) The DIC display is located at the bottom of the instrument panel cluster . It shows the status of many vehicle systems and enables access to the personalization menu. The DIC buttons are located on the instrument panel, next to the steering wheel.
V ehicle Customization Some vehicle features can be programmed by using the DIC buttons next to the steering wheel. These features include: . Language . Door Lock and Unlock Settings . RKE Lock and Unlock Feedback . Lighting . Chime V olume . Memory Features .
Rear Vision Camera (RVC) The rear vision camera displays a view of the area behind the vehicle when the vehicle is shifted into R (Reverse) on the inside rear view mirror or the navigation screen, if equipped. T o clean the camera lense, located below the tailgate handle, rinse it with water and wipe it with a soft cloth.
Performance and Maintenance StabiliT rak ® The vehicle may have a traction control system that limits wheel spin and the StabiliT rak system that assists with directional control of the vehicle in difficult driving conditions. Both systems turn on automatically every time the vehicle is started.
Y ou may notice during cooler conditions that the low tire pressure warning light will appear when the vehicle is first started and then turn off as you drive. This may be an early indicator that your tire pressures are getting low and the tires need to be inflated to the proper pressure.
Fuel E85 (85% Ethanol) This vehicle has a yellow fuel cap and can use either unleaded gasoline or ethanol fuel containing up to 85% ethanol (E85). See Gasoline Octane on page 6 ‑ 6 and Fuel E85 (85% Ethanol) on page 6 ‑ 8 . Driving for Better Fuel Economy Driving habits can affect fuel mileage.
OnStar ® OnStar ® uses several innovative technologies and live advisors to provide a wide range of safety , security , navigation, diagnostics, and calling services. Automatic Crash Response In a crash, built in sensors can automatically alert an OnStar advisor who is immediately connected to the vehicle to see if you need help.
The OnStar system can record and transmit vehicle information. This information is automatically sent to an OnStar call center when Q is pressed, ] is pressed, or if the airbags or ACR system deploy . This information usually includes the vehicle's GPS location and, in the event of a crash, additional information regarding the crash that the vehicle was involved in (e.
2 NOTES 1-28.
Section 2 Seats and Restraint System Head Restraints ............................... ..... 2-2 Front Seats ......................................... 2-4 Manual Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Power Seats .
Head Restraints The front seats have adjustable head restraints in the outboard seating positions. { W ARNING: With head restraints that are not installed and adjusted properly , there is a greater chance that occupants will suffer a neck/spinal injury in a crash.
Pull the head restraint up to raise it. T o lower the head restraint, press the button, located on the top of the seatback, and push the restraint down. Push down on the head restraint after the button is released to make sure that it is locked in place.
Front Seats Manual Seats { W ARNING: Y ou can lose control of the vehicle if you try to adjust a manual driver's seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Power Seats Driver's Seat with Power Seat Control, Power Recline, and Power Lumbar shown On a vehicle with power seats, the controls used to operate them are located on the outboard side of the seats. Move the seat forward or rearward by sliding the control forward or rearward.
Manual Lumbar On vehicles with this feature the control is located on the outboard side of the seat. Increase or decrease lumbar support by turning the knob forward or rearward. Power Lumbar On seats with power lumbar , the controls used to operate this feature are located on the outboard side of the seats.
The vehicle may have 4 – way lumbar . . T o increase lumbar support, press and hold the front of the control. . T o decrease lumbar support, press and hold the rear of the control. . T o raise the height of the lumbar support, press and hold the top of the control.
Heated and Cooled Seats If the front seats have the heated and cooled seat feature, the buttons used to control this feature are located on the front doors near the door handle. { (Cooled Seat): T o cool the entire seat, press the button with the cooled seat symbol.
T o save seating positions in memory: 1. Adjust the driver's seatback recliner , both outside mirrors, and the throttle and brake pedals to a comfortable position. See Outside Power Mirrors on page 3 ‑ 57 and Adjustable Throttle and Brake Pedal on page 3 ‑ 35 for more information.
Easy Exit Seat The control for this feature is located on the driver ’ s door panel between buttons 1 and 2. With the vehicle in P (Park), the driver's seat exit position can be recalled by pressing the exit button. Y ou will hear a single beep, and the driver ’ s seat will move back.
{ W ARNING: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts cannot do their job when you are reclined like this. The shoulder belt cannot do its job. In a crash, you could go into it, receiving neck or other injuries.
Manual Reclining Seatbacks On seats with manual reclining seatbacks, the lever used to operate them is located on the outboard side of the seat(s). T o recline the seatback: 1. Lift the recline lever . 2. Move the seatback to the desired position, then release the lever to lock the seatback in place.
Power Reclining Seatbacks If the seats have power reclining seatbacks, the control used to recline them is located on the outboard side of the seat behind the power seat control. . T o recline the seatback, tilt the top of the control rearward. . T o bring the seatback forward, tilt the top of the control forward.
T o fold either side of the seat do the following: 1. Push the rear seat head restraints all the way down. 2. Pull the seat loop located where the seatback and seat cushion meet. The seat cushion will release and allow you to tilt it toward the front of the vehicle.
{ W ARNING: A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash. The person wearing the belt could be seriously injured. After raising the rear seatback, always check to be sure that the safety belts are properly routed and attached, and are not twisted.
{ W ARNING: People riding on the tailgate (if equipped) can easily lose their balance and fall even when the vehicle is operated at low speeds. Falling from a moving vehicle may result in serious injuries or death. { W ARNING: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.
Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. T ake the simplest vehicle. Suppose it is just a seat on wheels. Put someone on it.
Get it up to speed. Then stop the vehicle. The rider does not stop. The person keeps going until stopped by something. In a real vehicle, it could be the windshield.
or the instrument panel... or the safety belts! With safety belts, you slow down as the vehicle does. Y ou get more time to stop. Y ou stop over more distance, and your strongest bones take the forces.
Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt? A: Y ou could be — whether you are wearing a safety belt or not. But your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted.
Occupants who are not buckled up can be thrown out of the vehicle in a crash. And they can strike others in the vehicle who are wearing safety belts. First, before you or your passenger(s) wear a safety belt, there is important information you should know .
Q: What is wrong with this? A: The shoulder belt is too loose. It will not give as much protection this way . { W ARNING: Y ou can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury .
Q: What is wrong with this? A: The lap belt is too loose. It will not give nearly as much protection this way . { W ARNING: Y ou can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen.
Q: What is wrong with this? A: The belt is buckled in the wrong buckle. { W ARNING: Y ou can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones.
Q: What is wrong with this? A: The belt is over an armrest. { W ARNING: Y ou can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries.
Q: What is wrong with this? A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. { W ARNING: Y ou can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury .
Q: What is wrong with this? A: The belt is behind the body . { W ARNING: Y ou can be seriously injured by not wearing the lap-shoulder belt properly . In a crash, you would not be restrained by the shoulder belt. Y our body could move too far forward increasing the chance of head and neck injury .
Q: What is wrong with this? A: The belt is twisted across the body . { W ARNING: Y ou can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly , or ask your dealer/retailer to fix it.
Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt except for the center front passenger position, if the vehicle has one, which has a lap belt. See Lap Belt on page 2 ‑ 35 for more information. The following instructions explain how to wear a lap-shoulder belt properly .
3. Push the latch plate into the buckle until it clicks. If you find that the latch plate will not go fully into the buckle, see if you are using the correct buckle. Pull up on the latch plate to make sure it is secure. If the belt is not long enough, see Safety Belt Extender on page 2 ‑ 36 .
T o unlatch the belt, push the button on the buckle. The belt should return to its stowed position. Before a door is closed, be sure the safety belt is out of the way . If a door is slammed against a safety belt, damage can occur to both the belt and the vehicle.
Safety Belt Pretensioners This vehicle has safety belt pretensioners for front outboard occupants. Although the safety belt pretensioners cannot be seen, they are part of the safety belt assembly . They can help tighten the safety belts during the early stages of a moderate to severe frontal, near frontal, or rear crash if the threshold conditions for pretensioner activation are met.
2. Place the guide over the belt, and insert the two edges of the belt into the slots of the guide. 3. Be sure that the belt is not twisted and it lies flat.
{ W ARNING: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces.
Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. A pregnant woman should wear a lap-shoulder belt, and the lap portion should be worn as low as possible, below the rounding, throughout the pregnancy .
T o make the belt shorter , pull its free end as shown until the belt is snug. If the belt is not long enough, see Safety Belt Extender on page 2 ‑ 36 . Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if necessary .
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle's safety belts. The manufacturer's instructions that come with the booster seat, state the weight and height limitations for that booster .
Q: What is the proper way to wear safety belts? A: An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should fit snugly below the hips, just touching the top of the thighs.
{ W ARNING: Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly . In a crash, the child would not be restrained by the shoulder belt.
Infants and Y oung Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
{ W ARNING: Never do this. Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child (Continued) W ARNING: (Continued) restraint in a rear seat.
Q: What are the different types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle's owner , are available in four basic types. Selection of a particular restraint should take into consideration not only the child's weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
{ W ARNING: A young child's hip bones are still so small that the vehicle's regular safety belt may not remain low on the hip bones, as it should. Instead, it may settle up around the child's abdomen. In a crash, the belt would apply force on a body area that is unprotected by any bony structure.
A booster seat (C-D) is a child restraint designed to improve the fit of the vehicle's safety belt system. A booster seat can also help a child to see out the window . Securing an Add-On Child Restraint in the V ehicle { W ARNING: A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle.
T o help reduce the chance of injury , the child restraint must be secured in the vehicle. Child restraint systems must be secured in vehicle seats by lap belts or the lap belt portion of a lap-shoulder belt, or by the LA TCH system. See Lower Anchors and T ethers for Children (LA TCH) on page 2 ‑ 47 for more information.
A label on your sun visor says, “ Never put a rear-facing child seat in the front. ” This is because the risk to the rear-facing child is so great, if the airbag deploys. { W ARNING: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates.
{ W ARNING: A child in a child restraint in the center front seat can be badly injured or killed by the frontal airbags if they inflate. Never secure a child restraint in the center front seat. It is always better to secure a child restraint in a rear seat.
Lower Anchors Lower anchors (A) are metal bars built into the vehicle. There are two lower anchors for each LA TCH seating position that will accommodate a child restraint with lower attachments (B). T op T ether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle.
In Canada, the law requires that forward-facing child restraints have a top tether , and that the tether be attached. Be sure to read and follow the instructions for your child restraint. If the child restraint does not have a top tether , one can be obtained, in kit form, for many child restraints.
The top tether anchors are located on the back of the rear seat frame above the floor for each rear seating position. Fold down the rear seatback(s) to access the anchors. See Rear Seat Operation on page 2 ‑ 13 . Be sure to use an anchor located on the same side of the vehicle as the seating position where the child restraint will be placed.
{ W ARNING: Do not attach more than one child restraint to a single anchor . Attaching more than one child restraint to a single anchor could cause the anchor or attachment to come loose or even break during a crash. A child or others could be injured.
1. 3. Route the top tether according to your child restraint instructions and the following instructions: If the position you are using does not have a headrest or head restraint and you are using a single tether , route the tether over the seatback. If the position you are using does not have a headrest or head restraint and you are using a dual tether , route the tether over the seatback.
{ W ARNING: If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked. 1. 5. Lift the seatback up and push it rearward.
Securing a Child Restraint in a Rear Seat Position When securing a child restraint in a rear seating position, study the instructions that came with the child restraint to make sure it is compatible with this vehicle. If the child restraint has the LA TCH system, see Lower Anchors and T ethers for Children (LA TCH) on page 2 ‑ 47 for how and where to install the child restraint using LA TCH.
3. Push the latch plate into the buckle until it clicks. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary . 4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock.
5. T o tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt, and feed the shoulder belt back into the retractor . When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt.
Securing a Child Restraint in the Right Front Seat Position This vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint on page 2 ‑ 45 . In addition, the vehicle may have a passenger sensing system which is designed to turn off the right front passenger frontal airbag under certain conditions.
If the child restraint has the LA TCH system, see Lower Anchors and T ethers for Children (LA TCH) on page 2 ‑ 47 for how and where to install the child restraint using LA TCH. If a child restraint is secured using a safety belt and it uses a top tether , see Lower Anchors and T ethers for Children (LA TCH) on page 2 ‑ 47 for top tether anchor locations.
4. Push the latch plate into the buckle until it clicks. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary . 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock.
6. T o tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor . When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt.
Airbag System The vehicle has the following airbags: . A frontal airbag for the driver . . A frontal airbag for the right front passenger . . A seat ‐ mounted side impact airbag for the driver . . A seat ‐ mounted side impact airbag for the right front passenger .
Here are the most important things to know about the airbag system: { W ARNING: Y ou can be severely injured or killed in a crash if you are not wearing your safety belt — even if you have airbags. Airbags are designed to work with safety belts, but do not replace them.
{ W ARNING: Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle's safety belt system nor its airbag system is designed for them.
The right front passenger frontal airbag is in the instrument panel on the passenger's side. Driver Side Shown, Passenger Side Similar The seat ‐ mounted side impact airbags for the driver and right front passenger are in the side of the seatbacks closest to the door .
Driver Side shown, Passenger Side similar The roof-rail airbags for the driver , right front passenger , and second row outboard passengers are in the ceiling above the side windows. { W ARNING: If something is between an occupant and an airbag, the airbag might not inflate properly or it might force the object into that person causing severe injury or even death.
When Should an Airbag Inflate? Frontal airbags are designed to inflate in moderate to severe frontal or near-frontal crashes to help reduce the potential for severe injuries mainly to the driver's or right front passenger's head and chest. However , they are only designed to inflate if the impact exceeds a predetermined deployment threshold.
In addition, the vehicle has dual-stage frontal airbags. Dual-stage airbags adjust the restraint according to crash severity . The vehicle has electronic frontal sensors, which help the sensing system distinguish between a moderate frontal impact and a more severe frontal impact.
What Makes an Airbag Inflate? In a deployment event, the sensing system sends an electrical signal triggering a release of gas from the inflator . Gas from the inflator fills the airbag causing the bag to break out of the cover and deploy . The inflator , the airbag, and related hardware are all part of the airbag module.
What Will Y ou See After an Airbag Inflates? After the frontal airbags and seat-mounted side impact airbags inflate, they quickly deflate, so quickly that some people may not even realize an airbag inflated. Roof-rail airbags may still be at least partially inflated for some time after they deploy .
The vehicle has a feature that may automatically unlock the doors, turn on the interior lamps and hazard warning flashers, and shut off the fuel system after the airbags inflate. Y ou can lock the doors, turn off the interior lamps and hazard warning flashers by using the controls for those features.
Passenger Sensing System If the vehicle has the passenger airbag status indicator pictured in the following illustration, then the vehicle has a passenger sensing system for the right front passenger position. The passenger airbag status indicator , if equipped, is visible on the overhead console when the vehicle is started.
A label on the sun visor says, “ Never put a rear-facing child seat in the front. ” This is because the risk to the rear-facing child is so great, if the airbag deploys. { W ARNING: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates.
When the passenger sensing system has turned off the right front passenger frontal airbag, the off indicator will light and stay lit to remind you that the airbag is off. See Passenger Airbag Status Indicator on page 4 ‑ 29 . The passenger sensing system is designed to turn on (may inflate) the right front passenger frontal airbag anytime the system senses that a person of adult size is sitting properly in the right front passenger seat.
4. Reinstall the child restraint following the directions provided by the child restraint manufacturer and refer to Securing a Child Restraint in the Right Front Seat Position on page 2 ‑ 57 . 5. If, after reinstalling the child restraint and restarting the vehicle, the on indicator is still lit, turn the vehicle off.
If this happens, use the following steps to allow the system to detect that person and enable the right front passenger frontal airbag: 1. T urn the vehicle off. 2. Remove any additional material from the seat, such as blankets, cushions, seat covers, seat heaters, or seat massagers.
Servicing Y our Airbag-Equipped V ehicle Airbags affect how the vehicle should be serviced. There are parts of the airbag system in several places around the vehicle. Y our dealer/retailer and the service manual have information about servicing the vehicle and the airbag system.
or with GM covers, upholstery or trim designed for a different vehicle. Any object, such as an aftermarket seat heater or a comfort enhancing pad or device, installed under or on top of the seat fabric, could also interfere with the operation of the passenger sensing system.
Restraint System Check Checking the Restraint Systems Safety Belts Now and then, check that the safety belt reminder light, safety belts, buckles, latch plates, retractors, and anchorages are all working properly . Look for any other loose or damaged safety belt system parts that might keep a safety belt system from doing its job.
Replacing Restraint System Parts After a Crash { W ARNING: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. T o help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.
2 NOTES 2-80.
Section 3 Features and Controls Keys ........................... ..................... 3-3 Remote Keyless Entry (RKE) System . . . . . . . . . . . 3-4 Remote Keyless Entry (RKE) System O p e r a t i o n ................... ............... ... 3 - 4 Remote Vehicle Start .
Section 3 Features and Controls Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-50 Shifting Into Park . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-51 Shifting Out of Park . . . . . . . . . . . . . . .
Keys { W ARNING: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and children could be seriously injured or killed if caught in the path of a closing window .
Remote Keyless Entry (RKE) System See Radio Frequency Statement on page 8 ‑ 19 for information regarding Part 15 of the Federal Communications Commission (FCC) Rules and RSS-210/21 1 of Industry and Science Canada. Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment.
/ (Remote V ehicle Start): For vehicles with this feature, press / to start the engine from outside the vehicle using the RKE transmitter . See Remote V ehicle Start on page 3 ‑ 7 for additional information. Q (Lock): Press to lock all the doors, including the tailgate.
Programming T ransmitters to the V ehicle Only RKE transmitters programmed to this vehicle will work. If a transmitter is lost or stolen, a replacement can be purchased and programmed through your dealer/retailer . When the replacement transmitter is programmed to this vehicle, all remaining transmitters must also be reprogrammed.
Remote V ehicle Start Y our vehicle may have a remote starting feature. This feature allows you to start the engine from outside of the vehicle. It may also start up the vehicle's heating or air conditioning systems and rear window defogger . Normal operation of the system will return after the key is turned to the ON/RUN position.
/ (Remote Start) : This button will be on the RKE transmitter if you have remote start. T o start the vehicle using the remote start feature: 1. Aim the transmitter at the vehicle. 2. Press and release the transmitter's lock button. The vehicle's doors will lock.
For example, if the lock button and then the remote start buttons are pressed again after the vehicle has been running for five minutes, 10 minutes are added, allowing the engine to run for 15 minutes. The additional ten minutes are considered a second remote vehicle start.
Doors and Locks Door Locks { W ARNING: Unlocked doors can be dangerous. . Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. The chance of being thrown out of the vehicle in a crash is increased if the doors are not locked.
Power Door Locks With power door locks, the switches on the front doors can be used to lock and unlock the vehicle. " (Unlock): Press to unlock the doors. Q (Lock): Remove the key from the ignition and press to lock the doors. Delayed Locking When locking the doors with the power lock switch and a door is open, the doors will lock five seconds after the last door is closed.
Rear Door Security Locks Y our vehicle has rear door security locks. These prevent passengers from opening the rear doors from the inside. The rear door security locks are located on the inside edge of each rear door . The rear doors must be open to access them.
Lockout Protection This feature protects you from locking your key in the vehicle when the key is in the ignition and a door is open. If the power lock switch is pressed when a door is open and the key is in the ignition, all of the doors will lock and then the driver's door will unlock.
The following are the main components of the Midgate ® system: A. Latch Levers B. Grab Handles C. Glass-Catch Release Button D. Glass Lock Knobs E. Window Retaining T abs F . Midgate ® Release Handle G. Window Alignment Arrows Rear Glass Removal and Storage { W ARNING: If the removable rear glass is not stored properly , it could be thrown about the vehicle in a crash or sudden maneuver .
2. Squeeze and pull down the latch levers (A), located near the upper corners of the rear glass, to unlatch. Once unlatched, the glass-catch release button (C) will catch the rear glass and prevent it from falling forward. 3. While holding the rear glass in place, press the glass-catch release button (C) and pull the top of the rear glass toward you using the grab handle(s) (B) located at the top of the rear glass.
4. With the rear glass tilted toward you, lift it out from the lower window frame channel. Use the grab handles to assist you in removing the rear glass. 5. Load the rear glass into the storage pocket in the Midgate ® , guiding the lower edge of the rear glass behind the three rear glass retaining tabs (E).
6. T urn both glass lock knobs (D), located at both top corners of the storage pocket, to the locked position. Push in on the corner of the rear glass to allow the lock knob to engage more easily . Once both glass lock knobs are in the locked position, the rear glass is securely stored.
Reinstalling the Rear Glass T o reinstall the rear glass, do the following: 1. Squeeze and pull down the latch levers (A), located near the upper corners of the rear glass, to unlatch. 2. Hold the rear glass in place with one hand and turn the glass lock knobs, located at both top corners of the glass storage pocket, to the unlocked position.
Be sure to align the rear glass side-to-side using the alignment arrows (G). 5. Apply a firm downward pressure and then push the rear glass flat against the window frame. Use the grab handles at the top of the rear glass to assist you. 6. Push the rear glass flat against the window frame and push each latch lever up until it locks.
Lowering the Midgate ® with the Rear Glass in Place The Midgate ® can be lowered to allow the cargo area of your vehicle to extend into the cab. The rear glass can be either installed in its normal position, or it can be removed and stored in the rear glass storage pocket.
3. Lower the Midgate ® until it is flat. Lowering the Midgate ® with the Rear Glass in the Storage Pocket Rear Glass Stored in Glass Storage Pocket 3-21.
Midgate ® Lowered with Crossbar Attached This procedure works the same as the procedure described previously , but when you lower the Midgate ® with the rear glass in the stored position, you will notice that the entire crossbar will lower with the Midgate ® .
W ARNING: (Continued) Do not allow people to ride on the tailgate. Be sure everyone in your vehicle is in a seat and using a safety belt properly . Use the Remote Keyless Entry (RKE) transmitter or power door lock switch to lock and unlock the tailgate.
Windows { W ARNING: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Power Windows { W ARNING: Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function and they could be seriously injured or killed if caught in the path of a closing window .
Express-Down Windows Windows with an express ‐ down feature allow the windows to be lowered without holding the switch. Press down fully on the window switch, then release, to activate the express ‐ down mode. The express ‐ down mode can be canceled at any time by pulling up on the front edge of the switch.
Theft-Deterrent Systems V ehicle theft is big business, especially in some cities. This vehicle has theft-deterrent features, however, they do not make it impossible to steal. Content Theft-Deterrent Y our vehicle has a content theft-deterrent alarm system.
If a locked driver door is opened without using the RKE transmitter , a ten second pre-alarm will occur . The horn will chirp and the lights will flash. If the key is not placed in the ignition and turned to ST ART or the door is not unlocked by pressing the unlock button on the RKE transmitter during the ten second pre-alarm, the alarm will go off.
P ASS-Key ® III+ Electronic Immobilizer See Radio Frequency Statement on page 8 ‑ 19 for information regarding Part 15 of the Federal Communications Commission (FCC) Rules and RSS-210/21 1 of Industry and Science Canada. P ASS-Key ® III+ Electronic Immobilizer Operation Y our vehicle has P ASS-Key ® III+ (Personalized Automotive Security System) theft-deterrent system.
It is possible for the P ASS-Key ® III+ decoder to learn the transponder value of a new or replacement key . Up to 10 keys may be programmed for the vehicle. The following procedure is for programming additional keys only . If all the currently programmed keys are lost or do not operate, you must see your dealer/retailer or a locksmith who can service P ASS-Key ® III+ to have keys made and programmed to the system.
Starting and Operating Y our V ehicle New V ehicle Break-In Notice: The vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: . Keep your speed at 55 mph (88 km/h) or less for the first 500 miles (805 km).
Ignition Positions The ignition switch has four different positions. T o shift out of P (Park), the ignition must be in ON/RUN or ACC/ACCESSORY and the regular brake pedal must be applied. A (LOCK/OFF) : This position locks the ignition. It also locks the transmission on automatic transmission vehicles.
C (ON/RUN) : This position can be used to operate the electrical accessories and to display some instrument panel cluster warning and indicator lights. The swi tch stays in this position when the engine is running. The transmission is also unlocked in this position on automatic transmission vehicles.
Starting the Engine Move the shift lever to P (Park) or N (Neutral). The engine will not start in any other position. T o restart the engine when the vehicle is already moving, use N (Neutral) only . Notice: Do not try to shift to P (Park) if the vehicle is moving.
2. If the engine does not start after 5 ‐ 10 seconds, especially in very cold weather (below 0°F or − 18°C), it could be flooded with too much gasoline. T ry pushing the accelerator pedal all the way to the floor and holding it there as you hold the key in ST ART for up to a maximum of 15 seconds.
The vehicle may have a memory function which lets pedal settings be saved and recalled. See Memory Seat, Mirrors, and Pedals on page 2 ‑ 8 for more information. Engine Coolant Heater The engine coolant heater can provide easier starting and better fuel economy during engine warm-up in cold weather conditions at or below − 18°C (0°F).
Active Fuel Management ™ V ehicles with V8 engines may have Active Fuel Management ™ . This system allows the engine to operate on either all or half of its cylinders, depending on the driving conditions. When less power is required, such as cruising at a constant vehicle speed, the system will operate in the half cylinder mode, allowing the vehicle to achieve better fuel economy .
When parked on a hill, especially when the vehicle has a heavy load, you may notice an increase in the effort to shift out of P (Park). See T orque Lock (Automatic T ransmission) under Shifting Into Park on page 3 ‑ 51 for more information. { W ARNING: It is dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set.
N (Neutral) : In this position, the engine does not connect with the wheels. T o restart the engine when the vehicle is already moving, use N (Neutral) only . Also, use N (Neutral) when the vehicle is being towed. { W ARNING: Shifting into a drive gear while the engine is running at high speed is dangerous.
M (Manual Mode) : This position lets drivers select the range of gears appropriate for current driving conditions. See Range Selection Mode later in this section. Notice: Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transmission.
Range Selection Mode On vehicles with a Range Selection Mode, this feature may be used to control the vehicle's transmission. T o use this feature, do the following: 1. Move the shift lever to the M (Manual Mode). 2. Press the plus/minus button, to upshift or downshift selecting the desired range of gears for current driving conditions.
T ow/Haul Mode The vehicle has a tow/haul mode. The tow/haul mode adjusts the transmission shift pattern to reduce shift cycling, providing increased performance, vehicle control, and transmission cooling while towing or hauling heavy loads. Press the button located on the end of the shift lever to turn the tow/haul on or off.
Cruise Grade Braking Cruise Grade Braking assists when driving on a downhill grade. It maintains vehicle speed by automatically implementing a shift schedule that uses the engine and the transmission to slow the vehicle. Cruise Grade Braking operates while Cruise Control is engaged in T ow/Haul mode to assist in maintaining vehicle speed under loaded vehicle conditions.
Front Axle The front axle engages and disengages automatically when you shift the transfer case. Some delay for the axle to engage or disengage is normal. Automatic T ransfer Case The transfer case knob is located to the left of the instrument panel cluster .
4 m (Four-Wheel Drive High): Use the four-wheel high position when you need extra traction, such as on snowy or icy roads or in most off-road situations. This setting also engages your front axle to help drive the vehicle. This is the best setting to use when plowing snow .
Shifting Into Four-Wheel Drive Low When Four-Wheel Low is engaged, vehicle speed should be kept below 45 mph (72 km/h). Extended high-speed operation in 4L may damage or shorten the life of the drivetrain. T o shift to the Four-Wheel Drive Low position, the ignition must be in ON/RUN and the vehicle must be stopped or moving less than 3 mph (5 km/h) with the transmission in N (Neutral).
The vehicle may have significant engagement noise and bump when shifting between Four-Wheel Drive Low and Four-Wheel Drive High ranges or from N (Neutral) while the engine is running. If the knob is turned to the Four-Wheel Drive High, AUTO, or T wo-Wheel Drive High switch position when the vehicle is in gear and/or moving, the Four-Wheel Drive High, AUTO or T wo-Wheel Drive High indicator light will flash for 30 seconds but will not complete the shift unless the vehicle is moving less than 3 mph (5 km/h) and the transmission is in N (Neutral).
Shifting Out of Neutral T o shift out of N Neutral do the following: 1. Set the parking brake and apply the regular brake pedal. 2. T urn the ignition to ON/RUN with the engine off, and shift the transmission to N (Neutral). 3. T urn the transfer case dial to the desired transfer case shift position (T wo-Wheel Drive High, Four-Wheel Drive High, AUTO).
Automatic T ransfer Case The transfer case knob is located to the left of the instrument panel cluster . Use this dial to shift into and out of four-wheel drive. The vehicle has Four-Wheel-Drive with StabiliTrak ® . For information on StabiliTrak ® , see StabiliT rak ® System on page 5 ‑ 6 .
Service Four Wheel Drive If the SERVICE 4 WHEEL DRIVE message stays on, you should take the vehicle to your dealer/retailer for service. See “ SERVICE 4 WHEEL DRIVE message ” under DIC Warnings and Messages on page 4 ‑ 57 . Shifting Into Four-Wheel Drive High or AUTO (Automatic Four-Wheel Drive) T urn the knob to the Four-Wheel High or AUTO position.
T o release the parking brake, hold the regular brake pedal down, then push down momentarily on the parking brake pedal until you feel the pedal release. Slowly pull your foot up off the park brake pedal. If the parking brake is not released when you begin to drive, the brake system warning light will flash and a chime will sound warning you that the parking brake is still on.
Leaving the V ehicle With the Engine Running { W ARNING: It can be dangerous to leave the vehicle with the engine running. The vehicle could move suddenly if the shift lever is not fully in P (Park) with the parking brake firmly set. If you have four-wheel drive and the transfer case is in N (Neutral), the vehicle will be free to roll, even if the shift lever is in P (Park).
Shifting Out of Park This vehicle is equipped with an electronic shift lock release system. The shift lock release is designed to: . Prevent ignition key removal unless the shift lever is in P (Park) with the shift lever button fully released, and . Prevent movement of the shift lever out of P (Park), unless the ignition is in ON/RUN or ACC/ACCESSORY and the regular brake pedal is applied.
Engine Exhaust { W ARNING: Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death. Exhaust may enter the vehicle if: . The vehicle idles in areas with poor ventilation (parking garages, tunnels, deep snow that may block underbody airflow or tail pipes).
Running the V ehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know . { W ARNING: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle.
Mirrors Manual Rearview Mirror Hold the inside rearview mirror in the center to move it for a clearer view behind your vehicle. Adjust the mirror to avoid glare from the headlamps behind you. Push the tab forward for daytime use and pull it for nighttime use.
Outside Power Mirrors V ehicles with outside power mirrors have controls located on the driver door . T o adjust each mirror: 1. Press (A) or (B) to select the driver or passenger side mirror . 2. Press one of the four arrows located on the control pad to adjust the mirror .
Resetting the Power Foldaway Mirrors Reset the power foldaway mirrors if: . The mirrors are accidentally obstructed while folding. . They are accidentally manually folded/unfolded. . The mirrors will not stay in the unfolded position. . The mirrors vibrate at normal driving speeds.
Outside Heated Mirrors < (Rear Window Defogger): Press to heat the mirrors. See “ Rear Window Defogger ” under Dual Automatic Climate Control System on page 4 ‑ 19 for more information. Object Detection Systems Ultrasonic Rear Parking Assist (URP A) For vehicles with the Ultrasonic Rear Parking Assist (URP A) system, it operates at speeds less than 8 km/h (5 mph), and assists the driver with parking and avoiding objects while in R (Reverse).
How the System Works URP A comes on automatically when the shift lever is moved into R (Reverse). A single tone sounds to indicate the system is working. URP A operates only at speeds less than 5 mph (8 km/h). An obstacle is indicated by audible beeps.
When the System Does Not Seem to Work Properly If the URP A system will not activate due to a temporary condition, the messages P ARK ASSIST OFF or P ARK ASST BLOCKED SEE OWNERS MANUAL will be displayed on the DIC. SERVICE P ARK ASSIST : If this message occurs, take the vehicle to your dealer/retailer to repair the system.
Rear Vision Camera (RVC) This vehicle may have a Rear Vision Camera system. Read this entire section before using it. { W ARNING: The Rear Vision Camera (RVC) system does not replace driver vision. RVC does not: . Detect objects that are outside the camera's field of view , below the bumper , or underneath the vehicle.
V ehicles With Navigation System The rear vision camera system is designed to help the driver when backing up by displaying a view of the area behind the vehicle. When the driver shifts the vehicle into R (Reverse), the video image automatically appears on the navigation screen.
Adjusting the Brightness and Contrast of the Screen T o adjust the brightness and contrast of the screen, press the MENU button while the rear vision camera image is on the display . Any adjustments made will only affect the rear vision camera screen.
Rear Vision Camera Location The image is provided by the camera located under the liftgate handle. The camera uses a special lens. The distance of the image that appears on the screen differs from the actual distance. The area displayed by the camera is limited.
When the System Does Not Seem T o Work Properly The rear vision camera system might not work properly or display a clear image if: . The RVC is turned off. See “ Turning the Rear Camera System On or Off ” earlier in this section. . It is dark. . The sun or the beam of headlights is shining directly into the camera lens.
Universal Home Remote System See Radio Frequency Statement on page 8 ‑ 19 for information regarding Part 15 of the Federal Communications Commission (FCC) Rules and RSS-210/21 1 of Industry and Science Canada. Universal Home Remote System Operation (With Three Round LED) This vehicle may have the Universal Home Remote System.
Programming Universal Home Remote — Rolling Code For questions or help programming the Universal Home Remote System, call 1-866-572-2728 or go to learcar2u.com. Most garage door openers sold after 1996 are Rolling Code units. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting.
3. Immediately return to the vehicle. Press and hold the Universal Home Remote button that will be used to control the garage door until the garage door moves. The indicator light, above the selected button, should slowly blink. This button may need to be held for up to 20 seconds.
T o program up to three devices: 1. T o verify that the garage door opener is a Fixed Code unit, remove the battery cover on the hand held transmitter supplied by the manufacturer of the garage door opener motor . If there are a row of dip switches similar to the graphic above, the garage door opener is a Fixed Code unit.
Example of Eight Dip Switches with T wo Positions Example of Eight Dip Switches with Three Positions The panel of switches might not appear exactly as they do in the examples above, but they should be similar . The switch positions on the hand-held transmitter could be labeled, as follows: .
2. Write down the eight to 12 switch settings from left to right as follows: . When a switch is in the up position, write “ Left. ” . When a switch is in the down position, write “ Right. ” . If a switch is set between the up and down position, write “ Middle.
5. After entering all of the switch positions, again, firmly press and release all three buttons at the same time. The indicator lights will turn on. 6. Press and hold the button that will be used to control the garage door until the garage door moves.
Storage Areas Glove Box Lift up on the glove box lever to open it. Cupholders For vehicles with cupholders for front and rear passengers, the cupholders are located in the center console and on the back of the center console. Press down and release the access door to open and use the front cupholders.
Roof Rack System { W ARNING: If something is carried on top of the vehicle that is longer or wider than the roof rack — like paneling, plywood, or a mattress — the wind can catch it while the vehicle is being driven. The item being carried could be violently torn off, and this could cause a collision, and damage the vehicle.
Do not exceed the maximum vehicle capacity when loading the vehicle. For more information on vehicle capacity and loading, see Loading the Vehicle on page 5 ‑ 32 . . If small heavy objects are placed on the roof, cut a piece of 3/8 inch plywood to fit inside the crossrails and siderails to spread the load.
T o remove a cargo panel(s): 1. Lower the tailgate. See T ailgate on page 3 ‑ 22 for more information on the tailgate. The panels are embossed on the upper center portion with the numbers 1, 2 and 3. There are also numbered labels on the bottom of the panels.
After each cargo panel has been removed, store them within the cargo storage area using the cargo panel storage system. Cargo Panel Storage System The three cargo panels can be stored in the cargo area using the storage strap system. Always use the storage strap system to store the cargo panels while driving.
Use the following instructions for the proper storage sequence and location for each panel: A. Secure clip A on the storage strap. B. Secure clip B on the storage strap. C. Place the remaining primary straps on top of the lid and tray at the top of the cargo area.
3. Place the primary straps over the three cargo covers (A). Fasten the four strap clips (B). 4. T ighten all straps by pulling on the free end of each strap.
5. Close both cross locks at the center of the strap system to tightly secure. Panels 3, 2, 1 Loaded 3-81.
Reinstalling the Cargo Cover Panels The strap system can remain attached to the side of the cargo area while it is not in use, or it can be stored inside the top box storage compartment. See T op-Box Storage on page 3 ‑ 91 for more information. T o reinstall a cargo panel: 1.
2. The driver side cargo cover panel latch must lock in place before the passenger side latch can be locked. If this procedure is not followed exactly , the cargo cover panels might not correctly lock in place. Push the driver side latch toward the front of the vehicle to lock the cover in position.
Driver Side Shown, Passenger Side Similar Push the panel forward until it is snug against the other panel and then let the back of the panel down making sure that the pegs (A) align with the receivers (B). 4. Push the latches toward the front of the vehicle, starting with the driver side latch, to lock the panel in place.
2. Fold the four primary strap ends toward the center as shown. 3. T ake the short strap and wrap it around the folded webbing, forming a package. 3-85.
4. T ake the storage strap and wrap it around the package. Finally , attach the hooks to the webbing and place the straps inside the top box storage compartment. Cargo Tie Downs The vehicle has cargo tie downs, located in the rear cargo area. These can be used to secure cargo.
Even when all of these things are working properly and the cover system is on, there may be some instances (heavy rains, automated car washes, etc.) when water can collect the following areas: A. T op drain grates B. Removable front drain grate (Midgate ® drain gate) C.
T op Drain Grates – Removal and Cleaning The top drain grates are located near the rear window on both sides of the vehicle. Clean the grates and drains if there is a blockage. T o remove each drain grate, do the following: 1. Remove the cargo panels.
T o replace the drain grate: 1. Line up the clips on the vehicle with the slots in the grate and firmly push the grate down. Do not force the grate. If it does not clip into place, realign the clips with the holes and try again. Side Rail Channels The side rail channels are located on top of both sides of the cargo area.
Midgate ® Drain Grate Removal and Cleaning The removable Midgate drain grate is located near the base of the Midgate. After hauling dirt, wood chips, pebbles etc. the Midgate drain should be flushed with water . First remove the drain grate: 1. Lower the Midgate ® .
Cargo Area Floor Drains The cargo net has cut outs for the four cargo-area floor drains located under the cargo mat near the sides of the cargo area. Periodically flush the drains through the cut outs to clear debris and allow water to drain from the cargo area.
Sunroof Y our vehicle may be equipped with a power sliding sunroof. T o open or close the sunroof, the ignition needs to be turned to ON/RUN, or Retained Accessory Power (RAP) must be active. When RAP is active, the sunroof will work for 10 minutes after the ignition is turned off, or until a front door is opened.
Express-Open/Express-Close : T o express-open the sunroof, fully press and release the rear of the driver's side switch. The sunroof will open automatically . T o stop the sunroof partway , press the switch a second time. T o express-close the sunroof, fully press and release the front of the driver's side switch.
2 NOTES 3-94.
Section 4 Instrument Panel Instrument Panel Overview ............... ......... 4-3 Hazard W arning Flashers . . . . . . . . . . . . . . . . . . . . . . . 4-3 Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 T ilt Wheel .
Section 4 Instrument Panel T ow/Haul Mode Light . . . . . . . . . . . . . . . . . . . . . . . . . . 4-41 Fuel Gage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-41 Low Fuel W arning Light . . . . . . . . . . . . . . . . .
Instrument Panel Overview Hazard W arning Flashers | (Hazard W arning Flasher): Press this button located on top of the steering column, to make the front and rear turn signal lamps flash on and off. This warns others that you are having trouble. Press again to turn the flashers off.
T urn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: G : T urn and Lane Change Signals 5 3 : Headlamp High/Low-Beam Changer N : Windshield Wipers L : Windshield W asher Flash-to-Pass. Exterior Lamps.
T urn Signal On Chime If the turn signal is left on for more than 3/4 of a mile (1.2 km), a chime sounds at each flash of the turn signal and the message TURN SIGNAL ON also appears in the DIC. See DIC Warnings and Messages on page 4 ‑ 57 . T o turn the chime and message off, move the turn signal lever to the off position.
Windshield Wipers T urn the band with the wiper symbol to control the windshield wipers. 8 (Mist): Single wipe, turn to 8 , then release. Several wipes, hold the band on 8 longer . 9 (Off): Turns the windshield wipers of f. 6 (Adjustable Interval Wipes): T urn the band up for more frequent wipes or down for less frequent wipes.
Cruise Control { W ARNING: Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use the cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control.
Setting Cruise Control Cruise control will not work if the parking brake is set, or if the master cylinder brake fluid level is low . The cruise control light on the instrument panel cluster will come on after the cruise control has been set to the desired speed.
Reducing Speed While Using Cruise Control T o reduce your speed while using cruise control: . Press and hold the SET – button on the steering wheel until the desired lower speed is reached, then release it. . T o slow down in small amounts, press the SET – button on the steering wheel briefly .
Exterior Lamps The exterior lamps control is located on the instrument panel to the left of the steering wheel. It controls the following systems: . Headlamps . T aillamps . Parking Lamps . License Plate Lamps . Instrument Panel Lights The exterior lamps control has four positions: 9 (Off): Turns off the automatic headlamps and daytime running lamps (DRL).
When the headlamps are turned on while the vehicle is on, the headlamps turn off automatically 10 minutes after the ignition is turned off. When the headlamps are turned on while the vehicle is off, the headlamps will stay on for 10 minutes before automatically turning off to prevent the battery from being drained.
Automatic Headlamp System When it is dark enough outside and the headlamp switch is in AUTO, the automatic headlamp system turns on the headlamps along with other lamps such as the taillamps, sidemarker , parking lamps, roof marker lamps, and the instrument panel lights.
Fog Lamps If your vehicle has fog lamps you can use them for better vision in foggy or misty conditions. Y our parking lamps and/or low-beam headlamps must be on for your fog lamps to work. The fog lamp button is located on the left side of your instrument panel.
Dome Lamps The dome lamps come on when any door is opened. They turn off after all the doors are closed. The dome lamps can also be turned on by turning the instrument panel brightness knob, located on the instrument panel to the left of the steering column, clockwise to the farthest position.
A high electrical load occurs when several of the following are on, such as: headlamps, high beams, fog lamps, rear window defogger , climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets.
Ashtray(s) and Cigarette Lighter For vehicles with an ashtray it is located in the center console or on the instrument panel. Pull up on the ashtray door to open it if it is in the console or pull the door open it if it is on the instrument panel. Notice: If papers, pins, or other flammable items are put in the ashtray , hot cigarettes or other smoking materials could ignite them and possibly damage the vehicle.
9 (Fan Control): Turn clockwise or counterclockwise to increase or decrease the fan speed. T urn the knob all the way counterclockwise to turn the front system off. Air Delivery Mode Control : Turn clockwise or counterclockwise to change the direction of the airflow inside the vehicle.
: (Outside Air): Press to turn the outside air mode on. An indicator light comes on to show that outside air is on. Air from outside the vehicle is circulated throughout the vehicle. The outside air mode can be used with all modes, but it cannot be used with the recirculation mode.
Dual Automatic Climate Control System The heating, cooling, and ventilation in the vehicle can be controlled with this system. The vehicle also has a flow-through ventilation system described later in this section. A. Driver and Passenger T emperature Controls B.
Driver and Passenger Side T emperature Controls The driver and passenger side temperature buttons are used to adjust the temperature of the air coming through the system on the driver or passenger's side of the vehicle. The temperature can be adjusted even if the system is turned off.
2. Set the driver and passenger temperature. T o find your comfort setting, start with a 23°C (74°F) temperature setting and allow about 20 minutes for the system to regulate. Use the driver or passenger temperature buttons to adjust the temperature setting as necessary .
6 (Floor): Air is directed to the floor outlets, with some to the windshield, side window outlets, and second row floor outlets. In this mode, the system automatically selects outside air . - (Defog): This mode clears the windows of fog or moisture. Air is directed to the windshield, floor outlets, and side window vents.
@ (Recirculation): Press to turn the recirculation mode on. An indicator light comes on to show that the recirculation is on. This mode recirculates and helps to quickly cool the air inside the vehicle. It can be used to help prevent outside air and odors from entering the vehicle.
Sensors The solar sensor , located in the defrost grille, middle of the instrument panel, monitors the solar heat. Do not cover the solar sensor or the system will not work properly . There is also an interior temperature sensor located next to the steering wheel that measures the temperature of the air inside your vehicle.
Outlet Adjustment Y our vehicle has air outlets located in the center and on the side of your instrument panel that allow you to adjust the direction and amount of airflow inside the vehicle. Move the louvers up or down. Use the thumbwheel next to or underneath the outlet to close the louvers.
Instrument Panel Cluster United States version shown. Canada similar 4-26.
Speedometer and Odometer The speedometer shows the vehicle's speed in both kilometers per hour (km/h) and miles per hour (mph). The odometer shows how far the vehicle has been driven, in either kilometers (used in Canada) or miles (used in the United States).
Passenger Safety Belt Reminder Light For vehicles equipped with the passenger safety belt reminder light, several seconds after the engine is started, a chime sounds for several seconds to remind the front passenger to buckle their safety belt. The passenger safety belt light, located on the overhead console, comes on and stays on for several seconds, flashes for several more seconds and then comes on solid for several more.
If there is a problem with the airbag system, an airbag Driver Information Center (DIC) message can also come on. See DIC Warnings and Messages on page 4 ‑ 57 for more information. Passenger Airbag Status Indicator If the vehicle has the airbag status indicator pictured in the following illustration, then the vehicle has a passenger sensing system for the right front passenger position.
If the word ON or the on symbol is lit on the passenger airbag status indicator , it means that the right front passenger frontal airbag is enabled (may inflate). If the word OFF or the off symbol is lit on the airbag status indicator , it means that the passenger sensing system has turned off the right front passenger frontal airbag.
V oltmeter Gage When the engine is not running, but the ignition is on, this gage shows the battery's state of charge in DC volts. When the engine is running, the gage shows the condition of the charging system. The charging system regulates voltage based on the state of the battery for improved fuel economy and battery life.
If the warning light comes on and a chime sounds there could be a brake problem. Have the brake system inspected right away . This light can also come on due to low brake fluid. See Brakes on page 6 ‑ 36 for more information. United States Canada This light comes on briefly when the ignition key is turned to ON/RUN.
Antilock Brake System (ABS) W arning Light For vehicles with the Antilock Brake System (ABS), this light comes on briefly when the engine is started. If it does not, have the vehicle serviced by your dealer/ retailer . If the system is working normally the indicator light then goes off.
Engine Coolant T emperature Gage United States Canada This gage shows the engine coolant temperature. It also provides an indicator of how hard the vehicle is working. During a majority of the operation, the gage will read 210°F (100°C) or less. If the vehicle is pulling a load or going up hills, it is normal for the temperature to fluctuate and approach the 250°F (122°C) mark.
When the Light is On Steady This indicates that one or more of the tires is significantly underinflated. A tire pressure message in the Driver Information Center (DIC), can accompany the light. See Driver Information Center (DIC) on page 4 ‑ 43 for more information.
Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle. This system assists the service technician in correctly diagnosing any malfunction. Notice: If the vehicle is continually driven with this light on, after a while, the emission controls might not work as well, the vehicle's fuel economy might not be as good, and the engine might not run as smoothly .
Light On Steady : An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. An emission system malfunction might be corrected by doing the following: . Make sure the fuel cap is fully installed. See Filling the T ank on page 6 ‑ 10 .
Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration.
This light comes on briefly while starting the engine. If it does not, have the vehicle serviced by your dealer/retailer . If the system is working normally the indicator light then goes off. If the light comes on and stays on, it means that oil is not flowing through the engine properly .
Security Light For information regarding this light and the vehicle's security system, see Content Theft-Deterrent on page 3 ‑ 27 . Fog Lamp Light The fog lamp light comes on when the fog lamps are in use. The light goes out when the fog lamps are turned off.
T ow/Haul Mode Light For vehicles with the tow/haul mode feature, this light comes on when the T ow/Haul mode has been activated. For more information, see T ow/Haul Mode on page 3 ‑ 42 . Fuel Gage United States Canada When the ignition is on, the fuel gage shows how much fuel the vehicle has left in the tank.
The gage first indicates empty before the vehicle is out of fuel, and the fuel tank should be filled soon. When the fuel tank is low , the FUEL LEVEL LOW message appears in the Driver Information Center (DIC). See DIC Warnings and Messages on page 4 ‑ 57 for more information.
Driver Information Center (DIC) Y our vehicle has a Driver Information Center (DIC). The DIC displays information about your vehicle. It also displays warning messages if a system problem is detected. All messages will appear in the DIC display located below the tachometer in the instrument panel cluster .
DIC Buttons The buttons are the trip/fuel, vehicle information, customization, and set/reset buttons. The button functions are detailed in the following pages. 3 (T rip/Fuel): Press this button to display the odometer , trip odometer , fuel range, average economy , fuel used, timer , instantaneous economy and Active Fuel Management ™ indicator , and transmission temperature.
T rip/Fuel Menu Items 3 (T rip/Fuel): Press this button to scroll through the following menu items: Odometer Press the trip/fuel button until ODOMETER displays. This display shows the distance the vehicle has been driven in either miles (mi) or kilometers (km).
Fuel Range Press the trip/fuel button until FUEL RANGE displays. This display shows the approximate number of remaining miles (mi) or kilometers (km) the vehicle can be driven without refueling. The display will show LOW if the fuel level is low. The fuel range estimate is based on an average of the vehicle's fuel economy over recent driving history and the amount of fuel remaining in the fuel tank.
T ransmission T emperature Press the trip/fuel button until TRANS TEMP displays. This display shows the temperature of the automatic transmission fluid in either degrees Fahrenheit (°F) or degrees Celsius (°C). Instantaneous Economy and Active Fuel Management ™ Indicator If your vehicle has this display , press the trip/fuel button until INST ECON V8 displays.
Remember , you must reset the OIL LIFE display yourself after each oil change. It will not reset itself. Also, be careful not to reset the OIL LIFE display accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change.
Relearn Remote Key This display allows you to match Remote Keyless Entry (RKE) transmitters to your vehicle. This procedure will erase all previously learned transmitters. Therefore, they must be relearned as additional transmitters. T o match an RKE transmitter to your vehicle: 1.
T rip Odometer Press the trip odometer reset stem until TRIP displays. This display shows the current distance traveled in either miles (mi) or kilometers (km) since the last reset for the trip odometer . The trip odometer can be reset to zero by pressing and holding the trip odometer reset stem while the trip odometer is displayed.
DIC Operation and Displays (Without DIC Buttons) If your vehicle does not have DIC buttons, the information below explains the operation of this system. The DIC has different displays which can be accessed by pressing the trip odometer reset stem located on the instrument panel cluster .
T rip Odometer Press the trip odometer reset stem until TRIP displays. This display shows the current distance traveled in either miles (mi) or kilometers (km) since the last reset for the trip odometer . The trip odometer can be reset to zero by pressing and holding the trip odometer reset stem while the trip odometer is displayed.
Compass Zone Setting This display allows for setting the compass zone. See DIC Compass on page 4 ‑ 55 for more information. Compass Recalibration This display allows for calibrating the compass. See DIC Compass on page 4 ‑ 55 for more information.
Relearn Remote Key T o access this display , the vehicle must be in P (Park). This display allows you to match Remote Keyless Entry (RKE) transmitters to your vehicle. This procedure will erase all previously learned transmitters. Therefore, they must be relearned as additional transmitters.
DIC Compass Y our vehicle may have a compass in the Driver Information Center (DIC). Compass Zone The zone is set to zone eight upon leaving the factory . Y our dealer/retailer will set the correct zone for your location. Under certain circumstances, such as during a long distance cross-country trip or moving to a new state or province, it will be necessary to compensate for compass variance by resetting the zone through the DIC if the zone is not set correctly .
2. Find the vehicle's current location and variance zone number on the map. Zones 1 through 15 are available. 3. Press the set/reset button to scroll through and select the appropriate variance zone. 4. Press the trip/fuel button until the vehicle heading, for example, N for North, is displayed in the DIC.
T o calibrate the compass, use the following procedure: Compass Calibration Procedure 1. Before calibrating the compass, make sure the compass zone is set to the variance zone in which the vehicle is located. See “ Compass V ariance (Zone) Procedure ” earlier in this section.
BA TTERY LOW ST ART VEHICLE When the vehicle ’ s battery is severely discharged, this message will display and four chimes will sound. Start the vehicle immediately . If the vehicle is not started and the battery continues to discharge, the climate controls, heated seats, and audio systems will shut off and the vehicle may require a jump start.
As soon as it is safe to do so, carefully pull your vehicle over to the side of the road and turn the ignition off. Check the wiring connection to the trailer and turn the ignition back on. This message clears if the trailer is reconnected. This message also clears if you acknowledge it.
ENGINE OVERHEA TED IDLE ENGINE Notice: If you drive your vehicle while the engine is overheating, severe engine damage may occur . If an overheat warning appears on the instrument panel cluster and/or DIC, stop the vehicle as soon as possible. See Engine Overheating on page 6 ‑ 31 for more information.
ICE POSSIBLE DRIVE WITH CARE This message displays when ice conditions are possible. LEFT REAR DOOR OPEN This message displays and a chime sounds if the driver side rear door is not fully closed and the vehicle is shifted out of P (Park). Stop and turn off the vehicle, check the door for obstructions, and close the door again.
REMOTE KEY LEARNING ACTIVE This message displays while you are matching a Remote Keyless Entry (RKE) transmitter to your vehicle. See “ Matching Transmitter(s) to Y our Vehicle ” under Remote Keyless Entry (RKE) System Operation on page 3 ‑ 4 and DIC Operation and Displays (With DIC Buttons) on page 4 ‑ 43 or DIC Operation and Displays (Without DIC Buttons) on page 4 ‑ 51 for more information.
SERVICE BRAKE SYSTEM This message displays along with the brake system warning light if there is a problem with the brake system. See Brake System Warning Light on page 4 ‑ 31 . If this message appears, stop as soon as possible and turn off the vehicle.
SERVICE TIRE MONITOR SYSTEM On vehicles with the Tire Pressure Monitor System (TPMS), this message displays if a part on the TPMS is not working properly . The tire pressure light also flashes and then remains on during the same ignition cycle. See Tire Pressure Light on page 4 ‑ 34 .
There are several conditions that can cause this message to appear . . One condition is overheating, which could occur if StabiliT rak activates continuously for an extended period of time. . The message also displays if the brake system warning light is on.
TIRE LOW ADD AIR TO TIRE On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the pressure in one or more of the vehicle's tires needs to be checked. This message also displays LEFT FRT (left front), RIGHT FRT (right front), LEFT RR (left rear), or RIGHT RR (right rear) to indicate the location of the low tire.
TRANSMISSION HOT IDLE ENGINE Notice: If you drive your vehicle while the transmission fluid is overheating and the transmission temperature warning is displayed on the instrument panel cluster and/or DIC, you can damage the transmission. This could lead to costly repairs that would not be covered by your warranty .
DIC V ehicle Customization (With DIC Buttons) Y our vehicle may have customization capabilities that allow you to program certain features to one preferred setting. Customization features can only be programmed to one setting on the vehicle and cannot be programmed to a preferred setting for two different drivers.
DISPLA Y LANGUAGE This feature allows you to select the language in which the DIC messages will appear . Press the customization button until the DISPLA Y LANGUAGE screen appears on the DIC display . Press the set/reset button once to access the settings for this feature.
AUTO DOOR UNLOCK This feature allows you to select whether or not to turn off the automatic door unlocking feature. It also allows you to select which doors and when the doors will automatically unlock. See Programmable Automatic Door Locks on page 3 ‑ 1 1 for more information.
NO CHANGE : No change will be made to this feature. The current setting will remain. T o select a setting, press the set/reset button while the desired setting is displayed on the DIC. REMOTE DOOR UNLOCK This feature allows you to select the type of feedback you will receive when unlocking the vehicle with the Remote Keyless Entry (RKE) transmitter .
EXIT LIGHTING This feature allows you to select the amount of time you want the exterior lamps to remain on when it is dark enough outside. This happens after the key is turned from ON/RUN to LOCK/OFF . Press the customization button until EXIT LIGHTING appears on the DIC display .
CHIME VOLUME This feature allows you to select the volume level of the chime. Press the customization button until CHIME VOLUME appears on the DIC display . Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: NORMAL : The chime volume will be set to a normal level.
EASY EXIT RECALL If your vehicle has this feature, it allows you to select your preference for the automatic easy exit seat feature. See Memory Seat, Mirrors, and Pedals on page 2 ‑ 8 for more information. Press the customization button until EASY EXIT RECALL appears on the DIC display .
MEMOR Y SEA T RECALL If your vehicle has this feature, it allows you to select your preference for the remote memory seat recall feature. See Memory Seat, Mirrors, and Pedals on page 2 ‑ 8 for more information. Press the customization button until MEMORY SEA T RECALL appears on the DIC display .
F ACTOR Y SETTINGS This feature allows you to set all of the customization features back to their factory default settings. Press the customization button until F ACTORY SETTINGS appears on the DIC display . Press the set/ reset button once to access the settings for this feature.
Audio System(s) Determine which radio the vehicle has and read the following pages to become familiar with its features. { W ARNING: T aking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others.
Setting the Clock T o set the time and date: 1. T urn the ignition key to ACC/ACCESSORY or ON/RUN, then press the O button to turn the radio on. 2. Press the H button to display HR, MIN, MM, DD, YYYY (hour , minute, month, day , and year). 3. Press the softkey located under any one of the tabs to change that setting.
Radio(s) Radio with CD/MP3 shown, Radio with CD/MP3/USB similar Radio with CD/MP3/DVD and USB The vehicle has one of these radios as its audio system. 4-79.
Radios with CD and DVD Radios with CD/MP3/DVD and USB may have a Bose ® Surround Sound System. Some of its features are explained later in this section under , “ Adjusting the Speakers (Balance/Fade) ” . If the vehicle has a Rear Seat Entertainment (RSE) system, it has a CD/MP3/DVD and USB radio.
Noise Compensation T echnology : V ehicles with the L TZ package and a Bose ® Audio System include the Bose AudioPilot ® noise compensation technology . When turned on, AudioPilot ® continuously adjusts the audio system equalization, to compensate for background noise, so that music always sounds the same at the set volume level.
Storing a Radio Station as a Favorite Drivers are encouraged to set up their radio station favorites while the vehicle is stopped. T une to favorite stations using the softkeys, favorites button, and steering wheel controls, if the vehicle has this feature.
Setting the T one (Bass/Midrange/T reble) BASS/MID/TREB (Bass, Midrange, or Treble) : T o adjust bass, midrange, or treble, press the f knob until the tone control tabs display . Continue pressing to highlight the desired tab, or press the softkey below the tab.
Adjusting the Speakers (Balance/Fade) BAL/F ADE (Balance/Fade) : T o adjust balance or fade, press the f knob until the speaker control tabs display . Continue pressing to highlight the desired tab, or press the softkey under the tab. T urn the f knob clockwise or counterclockwise to adjust the highlighted setting.
Undesired XM categories can be removed through the setup menu. T o remove an undesired category: 1. Press the MENU button. 2. Press the softkey below the XM CA T tab. 3. T urn the f knob to display the category to be removed. 4. Press the softkey under the Remove tab until the category name along with the word Removed displays.
Radio Messages for XM Only See XM Radio Messages on page 4 ‑ 1 12 later in this section for further detail. Care of the CD and DVD Player Do not add any label to a CD. It could get caught in the CD or DVD player . If a CD is recorded on a personal computer and a description label is needed, try labeling the top of the recorded CD with a marking pen.
Using the CD Player Inserting a Disc (Single CD Player) Insert a CD partway into the slot, label side up. The player pulls it in and the CD should begin playing. Inserting a Disc (In Either the DVD or CD Slot) Insert a CD partway into the slot, label side up.
Playing a CD f (T une): Turn to select tracks on the CD that is currently playing. © SEEK ¨ : Press the left arrow to go to the start of the current track, if more than ten seconds on the CD have played. Press the right arrow to go to the next track.
DVD/CD AUX (Auxiliary) : Press this button to cycle through DVD, CD, or Auxiliary when listening to the radio. The DVD/CD text label and a message showing the track or chapter number displays when a disc is in either slot. Press this button again and the system automatically searches for an auxiliary input device, such as a portable audio player .
Playing an MP3 CD-R or CD-RW Disc Radios with a Single CD player have the capability of playing an MP3 CD-R or CD-RW disc. For more information on how to play an MP3 CD-R or CD-RW disc, see “ Using an MP3 ” in the index. Playing an MP3/WMA CD-R or CD-RW Disc Radios with a CD and DVD player have the capability of playing an MP3/WMA CD-R or CD-RW disc.
Using the DVD Player The DVD player is controlled by the buttons on the remote control, or by the RSA system, or by the buttons on the radio faceplate. See “ Remote Control ” , under Rear Seat Entertainment (RSE) System on page 4 ‑ 125 and Rear Seat Audio (RSA) on page 4 ‑ 134 for more information.
Ejecting a Disc Press the Z button on the radio to eject the disc. If a disc is ejected from the radio, but not removed, the radio reloads the disc after a short period of time. The disc is stored in the radio. The radio does not resume play of the disc automatically .
f (T une): Turn to change tracks on a CD or DVD. © SEEK (Previous T rack/Chapter): Press the left arrow to return to the start of the current track or chapter . Press the left arrow again to go to the previous track or chapter . This button might not work when the DVD is playing the copyright information or the previews.
Some DVDs begin playing after the previews have finished, although there could be a delay of up to 30 seconds. If the DVD does not begin playing the movie automatically , press the softkey under the play/pause tab on the radio. If the DVD still does not play , refer to the on-screen instructions, if available.
Stopping and Resuming Playback T o stop playing a DVD without turning off the system, press the c button on the remote control, or press the softkey under the stop or the play/pause tab displayed on the radio. If the radio head is sourced to something other than DVD-V , press the DVD/CD AUX button to make DVD-V the active source.
Drivers are encouraged to set up any auxiliary device while the vehicle is in P (Park). See Defensive Driving on page 5 ‑ 2 for more information on driver distraction. T o use a portable audio player , connect a 3.5 mm (1/8 in) cable to the radio's front auxiliary input jack.
Using the USB Port Radios with a USB port can control a USB storage device or an iPod ® using the radio buttons and knobs. See Using an MP3 (Radios with CD) on page 4 ‑ 97 or Using an MP3 (Radios with CD and DVD) on page 4 ‑ 105 for information about how to connect and control a USB storage device or an iPod.
Compressed Audio or Mixed Mode Discs The radio can play discs that contain both uncompressed CD audio and MP3 files. If both formats are on the disc, the radio reads all MP3 files first, then the uncompressed CD audio files. CD ‐ R or CD ‐ RW Supported File and Folder Structure The radio supports: .
Empty Folder Folders that do not contain files are skipped, and the player advances to the next folder that contains files. Order of Play Compressed audio files are accessed in the following order: . Playlists (Px). . Files stored in the root directory .
Playlists can be changed by using the S c (previous) and c T (next) folder buttons, the f knob, or the © SEEK ¨ arrows. MP3 CD-R or CD-RW that have been recorded without using file folders can be played. If a CD-R or CD-RW contains more than the maximum of 50 folders, 15 playlists, and 512 folders and files, the player allows access and navigates up to the maximum, but all items over the maximum are not accessible.
T o listen to files by another artist, press the softkey located below either arrow tab. The disc goes to the next or previous artist in alphabetical order . Continue pressing either softkey below the arrow tab until the desired artist displays. T o change from playback by artist to playback by album: 1.
Using the Radio to Control a USB Storage Device or iPod The radio can control a USB storage device or an iPod using the radio buttons and knobs and display song information on the radio ’ s display . f (T une): Turn to select files. © SEEK: Press to go to the start of the track, if more than ten seconds have played.
c (Folder View): Press the softkey below c to view the contents of the current folder on the USB drive. T o browse and select files: 1. Press the softkey below c . 2. T urn f to scroll through the list of folders. 3. Press f to select the desired folder.
T o skip through large lists, the five softkeys can be used to navigate in the following order: . First softkey , first item in the list. . Second softkey , 1% through the list each time the softkey is pressed. . Third softkey , 5% through the list each time the softkey is pressed.
Using an MP3 (Radios with CD and DVD) Format The radio can play .mp3 or .wma files that were recorded onto a CD-R or CD-RW disc. The USB port can play .mp3 and .wma files that are stored on a USB storage device as well as AAC files that are stored on an iPod ® .
USB Supported File and Folder Structure The radio supports: . Up to 700 folders. . Up to 8 folders in depth. . Up to 65,535 files. . Folder and file names up to 64 bytes. . Files with an .mp3 or .wma file extension. . AAC files stored on an iPod. . F A T16 .
Order of Play Compressed audio files are accessed in the following order: . Playlists. . Files stored in the root directory . . Files stored in folders in the root directory . T racks are played in the following order: . Play begins from the first track in the first playlist and continues sequentially through all tracks in each playlist.
Playing an MP3/WMA File From a Disc (In Either the DVD or CD Slot) If a disc is inserted into the top DVD slot, the rear seat operator can turn on the video screen and use the remote control to navigate the CD (tracks only). f (T une): Turn to select MP3/WMA files.
When the scan is finished, the disc begins playing files in order by artist. The current artist playing is shown on the second line of the display . Once all songs by that artist are played, the player moves to the next artist in alphabetical order and begins playing files by that artist.
Using the Radio to Control a USB Storage Device or iPod The radio can control a USB storage device or an iPod using the radio buttons and knobs and display song information on the radio ’ s display . f (T une): Turn to select files. © SEEK: Press to go to the start of the track, if more than ten seconds have played.
c (Folder View): Press the softkey below c to view the contents of the current folder on the USB drive. T o browse and select files: 1. Press the softkey below c . 2. T urn f to scroll through the list of folders. 3. Press f to select the folder . If there is more than one folder , repeat Steps 1 and 2 until the folder is reached.
T o skip through large lists, the five softkeys can be used to navigate in the following order: . First softkey , first item in the list. . Second softkey , 1% through the list each time the softkey is pressed. . Third softkey , 5% through the list each time the softkey is pressed.
No XM Signal : The system is functioning correctly , but the vehicle is in a location that is blocking the XM ™ signal. When the vehicle is moved into an open area, the signal should return. Loading XM : The audio system is acquiring and processing audio and text data.
Navigation/Radio System For vehicles with a navigation radio system, see the separate Navigation System manual. Bluetooth ® V ehicles with a Bluetooth system can use a Bluetooth capable cell phone with a Hands Free Profile to make and receive phone calls.
Pairing A Bluetooth enabled cell phone must be paired to the in ‐ vehicle Bluetooth system first and then connected to the vehicle before it can be used. See the cell phone manufacturers user guide for Bluetooth functions before pairing the cell phone.
Listing All Paired and Connected Phones 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. Say “ Bluetooth ” . The system responds with “ Bluetooth ready ” followed by a tone. 3. Say “ List ” .
Using the Store Command The store command allows a phone number to be stored without entering the digits individually . 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. Say “ Store ” . The system responds with “ Store, number please ” followed by a tone.
3. Say the first digit to be stored. The system will repeat back the digit it heard followed by a tone. Continue entering digits until the number to be stored is complete. . If an unwanted number is recognized by the system, say “ Clear ” at any time to clear the last number .
Using the Delete Command The delete command allows specific name tags to be deleted. T o use the delete command: 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. Say “ Delete ” . The system responds with “ Delete, please say the name tag ” followed by a tone.
Using the Dial Command 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. Say “ Dial ” . The system responds with “ Dial using <phone name> ” . “ Number please ” followed by a tone. 3.
Using the Call Command 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. Say “ Call ” . The system responds with “ Call using <phone name>. Please say the name tag ” followed by a tone. 3.
Call W aiting Call waiting must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. . Press b g to answer an incoming call when another call is active. The original call is placed on hold. . Press b g again to return to the original call.
T ransferring a Call Audio can be transferred between the in ‐ vehicle Bluetooth system and the cell phone. T o T ransfer Audio to the Cell Phone During a call with the audio in the vehicle: 1. Press b g . The system responds with “ Ready ” followed by a tone.
Sending a Number During a Call 1. Press b g . The system responds with “ Ready ” followed by a tone. 2. Say “ Dial ” . The system responds with “ Say a number to send tones ” followed by a tone. 3. Say the number to send. . If the system clearly recognizes the number it responds with “ OK, Sending Number ” and the dial tones are sent and the call continues.
Clearing the System Unless information is deleted out of the in ‐ vehicle Bluetooth system, it will be retained indefinitely . This includes all saved name tags in the phonebook and phone pairing information. For information on how to delete this information, see the above sections on Deleting a Paired Phone and Deleting Name T ags.
Parental Control can also be turned off by inserting or ejecting any disc, pressing the play icon on the radio DVD display menu, or changing an ignition position. Headphones The RSE includes two 2-channel wireless headphones that are dedicated to this system.
Battery Replacement T o change the batteries on the headphones, do the following: 1. T urn the screw to loosen the battery door located on the left side of the headphones. Slide the battery door open. 2. Replace the two batteries in the compartment. Make sure that they are installed correctly , using the diagram on the inside of the battery compartment.
T o use the auxiliary inputs of the RSE system, connect an external auxiliary device to the color-coded A/V jacks and turn both the auxiliary device and the video screen power on. If the video screen is in the DVD player mode, pressing the AUX (auxiliary) button on the remote control switches the video screen from the DVD player mode to the auxiliary device.
Video Screen The video screen is located in the overhead console. T o use the video screen, do the following: 1. Push the release button located on the overhead console. 2. Move the screen to the desired position. When the video screen is not in use, push it up into its locked position.
Remote Control Buttons O (Power): Press this button to turn the video screen on and off. P (Illumination): Press this button to turn the remote control backlight on. The backlight automatically turns off after seven to ten seconds if no other button is pressed while the backlight is on.
u (Next T rack/Chapter): Press this button to go to the beginning of the next chapter or track. This button might not work when the DVD is playing the copyright information or the previews. r (Fast Reverse): Press this button to fast reverse the DVD or CD.
Battery Replacement T o change the remote control batteries, do the following: 1. Slide the rear cover back on to the remote control. 2. Replace the two batteries in the compartment. Make sure that they are installed correctly , using the diagram on the inside of the battery compartment.
Tips and T roubleshoo ting Chart (cont'd) Problem Recommended Action The auxiliary source is running but there is no picture or sound. Check that the RSE video screen is in the auxiliary source mode. Check the auxiliary input connections at both devices.
Cleaning the RSE Overhead Console When cleaning the RSE overhead console surface, use only a clean cloth dampened with clean water . Cleaning the Video Screen When cleaning the video screen, use only a clean cloth dampened with clean water . Use care when directly touching or cleaning the screen, as damage could result.
P (Power): Press this button to turn RSA on and off. V olume : Turn this knob to increase or to decrease the volume of the wired headphones. The left knob controls the left wired headphones and the right knob controls the right wired headphones. SRCE (Source) : Press this button to switch between the radio FM, AM, or XM ™ (if equipped), CD, and if the vehicle has these features, DVD, front auxiliary , and rear auxiliary .
PROG (Program) : Press this button to go to the next preset radio station or channel set on the main radio. This function is inactive, with some radios, if the front seat passengers are listening to the radio. When a CD or DVD audio disc is playing, press this button to go to the beginning of the CD or DVD audio.
Radio T o select preset or favorite radio stations: Press and release w or x to go to the next or previous radio station stored as a preset or favorite. CD/DVD T o select tracks on a CD/DVD: Press and release w or x to go to the next or previous track.
Navigating an iPod or USB Device on the Main Audio Screen (V ehicles with a Navigation System) Press and release w or x to select the next or previous track within the selected category . Press and hold w or x to move quickly through the tracks. Press and release ¨ to move up one track within the selected category .
For vehicles with a navigation system: 1. Press and hold ¨ until a beep is heard, to place the radio into SCAN mode, a station will play for five seconds before moving to the next station. 2. T o stop the SCAN function, press ¨ again. While listening to a CD/DVD, press and hold ¨ to quickly move forward through the tracks.
XM ™ Satellite Radio Service XM Satellite Radio Service gives digital radio reception from coast-to-coast in the 48 contiguous United States, and in Canada. Just as with FM, tall buildings or hills can interfere with satellite radio signals, causing the sound to fade in and out.
Section 5 Driving Y our V ehicle Y our Driving, the Road, and the Vehicle . . . . . . . . . . 5-2 Defensive Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 D r u n k D r i v i n g ... ................................ 5 - 2 Control of a V ehicle .
Y our Driving, the Road, and the V ehicle Defensive Driving Defensive driving means “ always expect the unexpected. ” The first step in driving defensively is to wear your safety belt — See Safety Belts: They Are for Everyone on page 2 ‑ 15 . { W ARNING: Assume that other road users (pedestrians, bicyclists, and other drivers) are going to be careless and make mistakes.
For persons under 21, it is against the law in every U.S. state to drink alcohol. There are good medical, psychological, and developmental reasons for these laws. The obvious way to eliminate the leading highway safety problem is for people never to drink alcohol and then drive.
Avoid needless heavy braking. Some people drive in spurts, heavy acceleration followed by heavy braking, rather than keeping pace with traffic. This is a mistake. The brakes might not have time to cool between hard stops. The brakes will wear out much faster with a lot of heavy braking.
Let us say the road is wet and you are driving safely . Suddenly , an animal jumps out in front of you. Y ou slam on the brakes and continue braking. Here is what happens with ABS: A computer senses that the wheels are slowing down. If one of the wheels is about to stop rolling, the computer will separately work the brakes at each front wheel and at both rear wheels.
StabiliT rak ® System The vehicle has a vehicle stability enhancement system called StabiliT rak. It is an advanced computer controlled system that assists the driver with directional control of the vehicle in difficult driving conditions. StabiliT rak activates when the computer senses a discrepancy between the intended path and the direction the vehicle is actually traveling.
The StabiliT rak light will flash on the instrument panel cluster when the system is both on and activated. The system may be heard or felt while it is working; this is normal. The traction control disable button is located on the instrument panel below the climate controls.
T raction Control Operation The traction control system is part of the StabiliTrak system. T raction control limits wheel spin by reducing engine power to the wheels (engine speed management) and by applying brakes to each individual wheel (brake-traction control) as necessary .
Steering Power Steering If power steering assist is lost because the engine stops or the system is not functioning, the vehicle can be steered but it will take more effort. Steering Tips It is important to take curves at a reasonable speed. T raction in a curve depends on the condition of the tires and the road surface, the angle at which the curve is banked, and vehicle speed.
An emergency like this requires close attention and a quick decision. If holding the steering wheel at the recommended 9 and 3 o'clock positions, it can be turned a full 180 degrees very quickly without removing either hand. But you have to act fast, steer quickly , and just as quickly straighten the wheel once you have avoided the object.
Passing Passing another vehicle on a two-lane road can be dangerous. T o reduce the risk of danger while passing: . Look down the road, to the sides, and to crossroads for situations that might affect a successful pass. If in doubt, wait. . W atch for traffic signs, pavement markings, and lines that could indicate a turn or an intersection.
While driving on a surface with reduced traction, try your best to avoid sudden steering, acceleration, or braking, including reducing vehicle speed by shifting to a lower gear . Any sudden changes could cause the tires to slide. Y ou may not realize the surface is slippery until the vehicle is skidding.
Before Y ou Go Off-Roading . Have all necessary maintenance and service work done. . Make sure there is enough fuel, that fluid levels are where they should be, and that the spare tire is fully inflated. . Be sure to read all the information about four-wheel-drive vehicles in this manual.
Loading Y our V ehicle for Off-Road Driving { W ARNING: . Cargo on the load floor piled higher than the seatbacks can be thrown forward during a sudden stop. Y ou or your passengers could be injured. Keep cargo below the top of the seatbacks. . Unsecured cargo on the load floor can be tossed about when driving over rough terrain.
Environmental Concerns Off-road driving can provide wholesome and satisfying recreation. However , it also raises environmental concerns. We recognize these concerns and urge every off-roader to follow these basic rules for protecting the environment: .
Controlling the vehicle is the key to successful off-r oad driving. One of the best ways to control the vehicle is to control the speed. At higher speeds: . Y ou approach things faster and have less time to react. . There is less time to scan the terrain for obstacles.
When driving over bumps, rocks, or other obstacles, the wheels can leave the ground. If this happens, even with one or two wheels, you cannot control the vehicle as well or at all. Because you will be on an unpaved surface, it is especially important to avoid sudden acceleration, sudden turns, or sudden braking.
Driving Uphill Once you decide it is safe to drive up the hill: . Use a low gear and get a firm grip on the steering wheel. . Get a smooth start up the hill and try to maintain speed. Not using more power than needed can avoid spinning the wheels or sliding.
. If the engine has stopped running, you need to restart it. With the brake pedal pressed and the parking brake still applied, shift the transmission to P (Park) and restart the engine. Then, shift to R (Reverse), release the parking brake, and slowly back down the hill as straight as possible in R (Reverse).
Driving Downhill When off-roading takes you downhill, consider: . How steep is the downhill? Will I be able to maintain vehicle control? . What is the surface like? Smooth? Rough? Slippery? Hard-packed dirt? Gravel? . Are there hidden surface obstacles? Ruts? Logs? Boulders? .
Driving Across an Incline An off-road trail will probably go across the incline of a hill. T o decide whether to try to drive across the incline, consider the following: { W ARNING: Driving across an incline that is too steep will make your vehicle roll over .
Stalling on an Incline { W ARNING: Getting out on the downhill (low) side of a vehicle stopped across an incline is dangerous. If the vehicle rolls over , you could be crushed or killed. Always get out on the uphill (high) side of the vehicle and stay well clear of the rollover path.
{ W ARNING: Driving on frozen lakes, ponds, or rivers can be dangerous. Underwater springs, currents under the ice, or sudden thaws can weaken the ice. Y our vehicle could fall through the ice and you and your passengers could drown. Drive your vehicle on safe surfaces only .
After Off-Road Driving Remove any brush or debris that has collected on the underbody , chassis, or under the hood. These accumulations can be a fire hazard. After operation in mud or sand, have the brake linings cleaned and checked. These substances can cause glazing and uneven braking.
Driving in Rain and on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving through large puddles and deep ‐ standing or flowing water .
Before Leaving on a Long T rip T o prepare your vehicle for a long trip, consider having it serviced by your dealer/retailer before departing. Things to check on your own include: . Windshield Washer Fluid: Reservoir full? Windows clean — inside and outside? .
Hill and Mountain Roads Driving on steep hills or through mountains is different than driving on flat or rolling terrain. Tips for driving in these conditions include: . Keep the vehicle serviced and in good shape. . Check all fluid levels and brakes, tires, cooling system, and transmission.
Winter Driving Driving on Snow or Ice Drive carefully when there is snow or ice between the tires and the road, creating less traction or grip. Wet ice can occur at about 0°C (32°F) when freezing rain begins to fall, resulting in even less traction.
Blizzard Conditions Being stuck in snow can be in a serious situation. Stay with the vehicle unless there is help nearby . If possible, use the Roadside Assistance Program on page 8 ‑ 7 . T o get help and keep everyone in the vehicle safe: . T urn on the Hazard Warning Flashers on page 4 ‑ 3 .
T o save fuel, run the engine for only short periods as needed to warm the vehicle and then shut the engine off and close the window most of the way to save heat. Repeat this until help arrives but only when you feel really uncomfortable from the cold.
gears. Release the accelerator pedal while shifting, and press lightly on the accelerator pedal when the transmission is in gear . Slowly spinning the wheels in the forward and reverse directions causes a rocking motion that could free the vehicle. If that does not get the vehicle out after a few tries, it might need to be towed out.
Loading the V ehicle It is very important to know how much weight your vehicle can carry . This weight is called the vehicle capacity weight and includes the weight of all occupants, cargo, and all nonfactory-i nstalled options. T wo labels on your vehicle show how much weight it was designed to carry , the T ire and Loading Information label and the Certification /T ire label.
The T ire and Loading Information label also shows the size of the original equipment tires (C) and the recommended cold tire inflation pressures (D). For more information on tires and inflation see Tires on page 6 ‑ 54 and Inflation - Tire Pressure on page 6 ‑ 62 .
Example 1 Item Description T otal A V ehicle Capacity Weight for Example 1 = 1,000 lbs (453 kg) B Subtract Occupant Weight @ 150 lbs (68 kg) × 2 = 300 lbs (136 kg) C Available Occupant and Cargo Weig.
Example 3 Item Description T otal A V ehicle Capacity Weight for Example 3 = 1,000 lbs (453 kg) B Subtract Occupant Weight @ 200 lbs (91 kg) × 5 = 1,000 lbs (453 kg) C Available Cargo Weight = 0 lbs (0 kg) Refer to your vehicle's tire and loading information label for specific information about your vehicle's capacity weight and seating positions.
Certification/Tire Label A vehicle specific Certification/T ire label is attached to the rear edge of the driver's door. The label shows the size of your vehicle's original tires and the inflation pressures needed to obtain the gross weight capacity of your vehicle.
{ W ARNING: In the case of a sudden stop or collision, things carried in the bed of your truck could shift forward and come into the passenger area, injuring you and others. If you put things in the bed of your truck, you should make sure they are properly secured.
If you put things inside your vehicle — like suitcases, tools, packages, or anything else — they will go as fast as the vehicle goes. If you have to stop or turn quickly , or if there is a crash, they will keep going. { W ARNING: Things you put inside your vehicle can strike and injure people in a sudden stop or turn, or in a crash.
T owing T owing Y our V ehicle T o avoid damage, the disabled vehicle should be towed with all four wheels off the ground. Consult your dealer/retailer or a professional towing service if the disabled vehicle must be towed. See Roadside Assistance Program on page 8 ‑ 7 .
Dinghy T owing T wo-Wheel-Drive V ehicles and Four-Wheel Drive V ehicles with a Single Speed Automatic T ransfer Case Notice: If the vehicle is towed with all four wheels on the ground, the drivetrain components could be damaged. The repairs would not be covered by the vehicle warranty .
Four-Wheel Drive V ehicles with a T wo Speed Automatic T ransfer Case Use the following procedure to dinghy tow a four-wheel drive vehicle with a two speed automatic transfer case: 1. Position the vehicle being towed behind the tow vehicle and shift the transmission to P (Park).
Dolly T owing Front T owing (Front Wheels Off the Ground) T wo-Wheel-Drive V ehicles and Four-Wheel Drive V ehicles with a Single Speed Automatic T ransfer Case Notice: If a two-wheel drive vehicle or a four-wheel drive vehicle with a single speed automatic transfer case is towed with the rear wheels on the ground, the transmission could be damaged.
Four-Wheel Drive V ehicles with a T wo Speed Automatic T ransfer Case Use the following procedure to dolly tow a four-wheel drive vehicle from the front: 1. Attach the dolly to the tow vehicle following the dolly manufacturer's instructions. 2. Drive the front wheels onto the dolly .
Rear T owing (Rear Wheels Off the Ground) T wo-Wheel-Drive V ehicles and Four-Wheel Drive V ehicles with a Single Speed Automatic T ransfer Case Use the following procedure to dolly tow the vehicle from the rear: 1. Attach the dolly to the tow vehicle following the dolly manufacturer's instructions.
Four-Wheel Drive V ehicles with a T wo Speed Automatic T ransfer Case Use the following procedure to dolly tow a four-wheel drive vehicle from the rear: 1. Attach the dolly to the tow vehicle following the dolly manufacturer's instructions. 2. Drive the rear wheels onto the dolly .
Level Control Automatic Level Control The automatic level control rear suspension is available on light ‐ duty vehicles and comes as a part of the Autoride ® suspension, if equipped. This type of level control is fully automatic and will provide a better leveled riding position as well as better handling under a variety of passenger and loading conditions.
T owing a T railer Do not tow a trailer during break ‐ in. See New Vehicle Break-In on page 3 ‑ 31 for more information. { W ARNING: The driver can lose control when pulling a trailer if the correct equipment is not used or the vehicle is not driven properly .
Pulling A T railer Here are some important points: . There are many different laws, including speed limit restrictions, having to do with trailering. Make sure the rig will be legal, not only where you live but also where you will be driving. A good source for this information can be state or provincial police.
Use the following chart to determine how much the vehicle can weigh, based upon the vehicle model and options. Notice: Using a fifth-wheel or goose-neck hitch device on the vehicle could damage the vehicle. The repairs would not be covered by the vehicle warranty .
Weight of the T railer T ongue The tongue load (A) of any trailer is very important because it is also part of the vehicle weight. The Gross V ehicle Weight (GVW) includes the curb weight of the vehicle, any cargo carried in it, and the people who will be riding in the vehicle as well as trailer tongue weight.
T otal Weight on the V ehicle's Tires Be sure the vehicle's tires are inflated to the inflation pressures found on the Certification label on the drivers door or see Loading the Vehicle on page 5 ‑ 32 for more information. Make sure not to exceed the GVWR limit for the vehicle, or the RGA WR, with the tow vehicle and trailer fully loaded for the trip including the weight of the trailer tongue.
Weight ‐ Distributing Hitch Adjustment A : Body to Ground Distance B : Front of Vehicle When using a weight-distributing hitch, the spring bars should be adjusted so the distance (A) is the same after coupling the trailer to the tow vehicle and adjusting the hitch.
T ow/Haul Mode Pressing this button at the end of the shift lever turns on and off the tow/haul mode. This indicator light on the instrument panel cluster comes on when the tow/haul mode is on. T ow/Haul is a feature that assists when pulling a heavy trailer or a large or heavy load.
T railer Brakes A loaded trailer that weighs more than 2,000 lbs (900 kg) needs to have its own brake system that is adequate for the weight of the trailer . Be sure to read and follow the instructions for the trailer brakes so they are installed, adjusted and maintained properly .
{ W ARNING: Connecting a trailer that is not compatible with the ITBC system may result in reduced or complete loss of trailer braking. There may be an increase in stopping distance or trailer instability which could result in personal injury or damage to the vehicle, trailer , or other property .
T railer Brake Control Panel A. Manual T railer Brake Apply Lever B. T railer Gain Adjustment Buttons The ITBC system has a control panel located on the instrument panel to the left of the steering column. See Instrument Panel on page 1 ‑ 2 . The control panel allows adjustment to the amount of output, referred to as trailer gain, available to the electric trailer brakes and allows manual application the trailer brakes.
All DIC warning and service messages must first be acknowledged by the driver by pressing the odometer trip stem or the DIC V ehicle Information button (if equipped) before the Trailer Brake Display Page can be displayed and T railer Gain can be adjusted.
If the vehicle ’ s service brakes are applied while using the Manual Trailer Brake Apply Lever , the trailer output power will be the greater of the two. The trailer and the vehicle's brake lamps will come on when either vehicle braking or manual trailer brakes are applied.
6. Adjust the Trailer Gain to just below the point of trailer wheel lock-up, indicated by trailer wheel squeal or tire smoke when a trailer wheel locks. T railer wheel lock-up may not occur if towing a heavily loaded trailer . In this case, adjust the T railer Gain to the highest allowable setting for the towing condition.
T o determine if the electrical fault is on the vehicle side or trailer side of the trailer wiring harness connection, do the following: 1. Disconnect the trailer wiring harness from the vehicle. 2. T urn the ignition OFF . 3. W ait ten seconds, then turn the ignition back to RUN.
Driving with a T railer { W ARNING: When towing a trailer , exhaust gases may collect at the rear of the vehicle and enter if the liftgate, trunk/hatch, or rear-most window is open. Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled.
Following Distance Stay at least twice as far behind the vehicle ahead as you would when driving the vehicle without a trailer . This can help to avoid heavy braking and sudden turns. Passing More passing distance is needed when towing a trailer . The combination will not accelerate as quickly and is longer so it is necessary to go much farther beyond the passed vehicle before returning to the lane.
Driving On Grades Reduce speed and shift to a lower gear before starting down a long or steep downgrade. If the transmission is not shifted down, the brakes might get hot and no longer work well. V ehicles can tow in D (Drive). Shift the transmission to a lower gear if the transmission shifts too often under heavy loads and/or hilly conditions.
4. Reapply the brake pedal. Then apply the parking brake and shift into P (Park). 5. If the vehicle is four-wheel-drive and has a two-speed transfer case, be sure the transfer case is in a drive gear and not in N (Neutral). 6. Release the brake pedal.
T railer Wiring Harness Heavy-Duty T railer Wiring Harness Package The vehicle has a seven-pin universal heavy-duty trailer connector attached to the rear bumper beam next to the integrated trailer hitch. The seven-wire harness contains the following trailer circuits: .
Electric Brake Control Wiring Provisions These wiring provisions are included with the vehicle as part of the trailer wiring package. These provisions are for an electric brake controller . The instrument panel contains blunt cut wires near the data link connector for the trailer brake controller .
Section 6 Service and Appearance Care Service ......... ............................... ..... 6-3 Accessories and Modifications . . . . . . . . . . . . . . . . . . 6-3 California Proposition 65 Warning . . . . . . . . . . . . . . . 6-4 California Perchlorate Materials R e q u i r e m e n t s .
Section 6 Service and Appearance Care T ire Pressure Monitor System . . . . . . . . . . . . . . . . . 6-64 T ire Pressure Monitor Operation . . . . . . . . . . . . . . . 6-65 T ire Inspection and Rotation . . . . . . . . . . . . . . . . . . . 6-68 When It Is T ime for New Tires .
Service For service and parts needs, visit your dealer/retailer . Y ou will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories and Modifications When non ‐ dealer/non ‐ retailer accessories are added to the vehicle, they can affect vehicle performance and safety , including such things as airbags, braking, stability , ride and handling, emissions systems, aerodynamics, durability , and electronic systems like antilock brakes, traction control, and stability control.
California Proposition 65 W arning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems, many fluids, and some component wear by-products contain and/or emit these chemicals.
Keep a record with all parts receipts and list the mileage and the date of any service work performed. See Maintenance Record on page 7 ‑ 15 . Adding Equipment to the Outside of the V ehicle Things added to the outside of the vehicle can affect the airflow around it.
Gasoline Octane Use regular unleaded gasoline with a posted octane rating of 87 or higher . If the octane rating is less than 87, an audible knocking noise, commonly referred to as spark knock, might be heard when driving. If this occurs, use a gasoline rated at 87 octane or higher as soon as possible.
Additives T o provide cleaner air , all gasolines in the United States are now required to contain additives that help prevent engine and fuel system deposits from forming, allowing the emission control system to work properly . In most cases, nothing should have to be added to the fuel.
Fuel E85 (85% Ethanol) This vehicle can use either unleaded gasoline or 85% ethanol fuel (E85). We encourage the use of E85 in vehicles that are designed to use it. The ethanol in E85 is a “ renewable ” fuel, meaning it is made from renewable sources such as corn and other crops.
E85 has less energy per gallon than gasoline, so you will need to refill the fuel tank more often when using E85 than when you are using gasoline. See Filling the T ank on page 6 ‑ 10 . Notice: Some additives are not compatible with E85 fuel and can harm the vehicle's fuel system.
Filling the T ank { W ARNING: Fuel vapor burns violently and a fuel fire can cause bad injuries. T o help avoid injuries to you and others, read and follow all the instructions on the fuel pump island. Turn off the engine when refueling. Do not smoke near fuel or when refueling the vehicle.
{ W ARNING: Fuel can spray out on you if you open the fuel cap too quickly . If you spill fuel and then something ignites it, you could be badly burned. This spray can happen if the tank is nearly full, and is more likely in hot weather . Open the fuel cap slowly and wait for any hiss noise to stop.
Filling a Portable Fuel Container { W ARNING: Never fill a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor . Y ou can be badly burned and the vehicle damaged if this occurs.
Hood Release T o open the hood: 1. Pull the handle with this symbol on it. It is located inside the vehicle to the lower left of the steering wheel. 2. Then go to the front of the vehicle and locate the secondary hood release, near the center of the grille.
Engine Compartment Overview When you open the hood on the 5.3L engine (6.0L similar), here is what you will see: 6-14.
A. Engine Air Cleaner/Filter on page 6 ‑ 20 . B. Coolant Surge T ank and Pressure Cap. See Cooling System on page 6 ‑ 26 . C. Remote Positive (+) T erminal. See Jump Starting on page 6 ‑ 40 . D. Battery on page 6 ‑ 39 . E. Engine Oil Fill Cap.
Engine Oil Checking Engine Oil It is a good idea to check the engine oil level at each fuel fill. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground. The engine oil dipstick handle is a yellow loop. See Engine Compartment Overview on page 6 ‑ 14 for the location of the engine oil dipstick.
See Engine Compartment Overview on page 6 ‑ 14 for the location of the engine oil fill cap. Add enough oil to put the level somewhere in the proper operating range. Push the dipstick all the way back in when through. What Kind of Engine Oil to Use Look for three things: .
Engine Oil Additives / Engine Oil Flushes Do not add anything to the oil. The recommended oils with the starburst symbol that meet GM Standard GM6094M are all that is needed for good performance and engine protection. Engine oil system flushes are not recommended and could cause engine damage not covered by the vehicle warranty .
Always reset the engine oil life to 100% after every oil change. It will not reset itself. T o reset the Engine Oil Life System on most vehicles: 1. Display the OIL LIFE REMAINING on the DIC. If the vehicle does not have DIC buttons, the vehicle must be in P (Park) to access this display .
Engine Air Cleaner/Filter See Engine Compartment Overview on page 6 ‑ 14 for the location of the engine air cleaner/filter . Inspect the air cleaner/filter at the Maintenance II intervals and replace it at the first oil change after each 50,000 mile (80 000 km) interval.
3. Remove the engine air cleaner/filter from the housing. Care should be taken to dislodge as little dirt as possible. 4. Clean the engine air cleaner/filter sealing surfaces and the housing. 5. Inspect or replace the engine air cleaner/filter . 6. Reinstall the cover and tighten the screws.
Automatic T ransmission Fluid When to Check and Change Automatic T ransmission Fluid It is usually not necessary to check the transmission fluid level. The only reason for fluid loss is a transmission leak or overheating the transmission. If you suspect a small leak, then use the following checking procedures to check the fluid level.
4. Allow the engine to idle (500 – 800 rpm) for at least one minute. Slowly release the brake pedal. 5. Keep the engine running and press the T rip/Fuel button or trip odometer reset stem until TRANS TEMP (T ransmission T emperature) displays on the Driver Information Center (DIC).
5. If the fluid level is below the COLD check band, add only enough fluid as necessary to bring the level into the COLD band. It does not take much fluid, generally less than one pint (0.5L). Do not overfill. 6. Perform a hot check at the first opportunity after the transmission reaches a normal operating temperature between 160°F to 200°F (71°C to 93°C).
3. Install the dipstick by pushing it back in all the way , wait three seconds, and then pull it back out again. 4. Check both sides of the dipstick and read the lower level. Repeat the check procedure to verify the reading. 5. Safe operating level is within the HOT cross hatch band on the dipstick.
Cooling System The cooling system allows the engine to maintain the correct working temperature. 5.3L Engine shown, 6.0L Engine similar A. Coolant Surge T ank B. Coolant Surge T ank Pressure Cap C. Engine Cooling Fan(s) { W ARNING: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury .
Notice: Using coolant other than DEX-COOL ® can cause premature engine, heater core, or radiator corrosion. In addition, the engine coolant could require changing sooner , at 50 000 km (30,000 miles) or 24 months, whichever occurs first. Any repairs would not be covered by the vehicle warranty .
. Protects against rust and corrosion. . Will not damage aluminum parts. . Helps keep the proper engine temperature. Notice: If an improper coolant mixture is used, the engine could overheat and be badly damaged. The repair cost would not be covered by the vehicle warranty .
How to Add Coolant to the Surge T ank { W ARNING: Y ou can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. Notice: This vehicle has a specific coolant fill procedure.
T urn the pressure cap slowly counterclockwise about one full turn. If you hear a hiss, wait for that to stop. A hiss means there is still some pressure left. 2. Keep turning the pressure cap slowly and remove it. 3. Fill the coolant surge tank with the proper mixture to the FULL COLD mark.
5. Replace the pressure cap. Be sure the pressure cap is hand-tight and fully seated. 6. V erify coolant level after engine is shut off and the coolant is cold. If necessary , repeat coolant fill procedure Steps 1 through 6. Notice: If the pressure cap is not tightly installed, coolant loss and possible engine damage may occur .
If Steam Is Coming From The Engine Compartment { W ARNING: Steam from an overheated engine can burn you badly , even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. T urn it off and get everyone away from the vehicle until it cools down.
If the temperature overheat gage is no longer in the overheat zone or an overheat warning no longer displays, the vehicle can be driven. Continue to drive the vehicle slow for about 10 minutes. Keep a safe vehicle distance from the car in front of you.
Power Steering Fluid See Engine Compartment Overview on page 6 ‑ 14 for reservoir location. When to Check Power Steering Fluid It is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or you hear an unusual noise.
Windshield W asher Fluid What to Use When windshield washer fluid needs to be added, be sure to read the manufacturer's instructions before use. Use a fluid that has sufficient protection against freezing in an area where the temperature may fall below freezing.
Brakes Brake Fluid The brake master cylinder reservoir is filled with DOT 3 brake fluid. See Engine Compartment Overview on page 6 ‑ 14 for the location of the reservoir . There are only two reasons why the brake fluid level in the reservoir might go down: .
Checking Brake Fluid Check brake fluid by looking at the brake fluid reservoir . See Engine Compartment Overview on page 6 ‑ 14 . The fluid level should be above MIN. If it is not, have the brake hydraulic system checked to see if there is a leak. After work is done on the brake hydraulic system, make sure the level is above the MIN but not over the MAX mark.
Brake Wear This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal firmly .
Battery Refer to the replacement number on the original battery label when a new battery is needed. See Engine Compartment Overview on page 6 ‑ 14 for battery location. { DANGER: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm.
Jump Starting If the vehicle's battery (or batteries) has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely . { W ARNING: Batteries can hurt you. They can be dangerous because: .
Notice: If you leave the radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by the warranty . Always turn off the radio and other accessories when jump starting the vehicle. 3. T urn off the ignition on both vehicles.
{ W ARNING: An electric fan can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan. { W ARNING: Using an open flame near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded.
6. Connect the red positive (+) cable to the positive (+) terminal of the vehicle with the dead battery . Use a remote positive (+) terminal if the vehicle has one. 7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery .
Notice: If the jumper cables are connected or removed in the wrong order , electrical shorting may occur and damage the vehicle. The repairs would not be covered by the vehicle warranty . Always connect and remove the jumper cables in the correct order , making sure that the cables do not touch each other or other metal.
Rear Axle When to Check Lubricant It is not necessary to regularly check rear axle fluid unless you suspect there is a leak or you hear an unusual noise. A fluid loss could indicate a problem. Have it inspected and repaired. All axle assemblies are filled by volume of fluid during production.
What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use. See Recommended Fluids and Lubricants on page 7 ‑ 1 1 . Four-Wheel Drive Lubricant checks in this section also apply to these vehicles. There are two additional systems that need lubrication.
When to Change Lubricant Refer to the Maintenance Schedule to determine how often to change the lubricant. See Scheduled Maintenance on page 7 ‑ 3 . What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use. See Recommended Fluids and Lubricants on page 7 ‑ 1 1 .
Headlamp Aiming The vehicle has a visual optical headlamp aiming system. The aim of the headlamps have been preset at the factory and should need no further adjustment. However , if the vehicle is damaged in a crash, the aim of the headlamps can be affected and adjustment can be necessary .
T o adjust the vertical aim: 1. Open the hood. See Hood Release on page 6 ‑ 13 for more information. 2. Locate the aim dot on the lens of the low ‐ beam headlamp. 3. Record the distance from the ground to the aim dot on the low ‐ beam headlamp. 4.
7. Locate the vertical headlamp aiming screws, which are under the hood near each headlamp assembly . The adjustment screw can be turned with a E8 T orx ® socket. 8. T urn the vertical aiming screw until the headlamp beam is aimed to the horizontal tape line.
Halogen Bulbs { W ARNING: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. Y ou or others could be injured. Be sure to read and follow the instructions on the bulb package. T aillamps, T urn Signal, Sidemarker , Stoplamps and Back-up Lamps A.
6. Press a new bulb into the bulb socket and insert the bulb socket into the taillamp assembly . T urn the bulb socket clockwise into the taillamp assembly until it clicks. 7. Reinstall the taillamp assembly making sure to line up the pins with the vehicle.
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear or cracking. See Scheduled Maintenance on page 7 ‑ 3 . Replacement blades come in different types and are removed in different ways. T o replace the wiper blade assembly , do the following: 1.
Tires Y our new vehicle comes with high-quality tires made by a leading tire manufacturer . If you ever have questions about your tire warranty and where to obtain service, see your vehicle W arranty booklet for details. For additional information refer to the tire manufacturer .
Tire Sidewall Labeling Useful information about a tire is molded into the sidewall. The following illustrations are examples of a typical P ‐ Metric and a L T ‐ Metric tire sidewall. Passenger (P ‐ Metric) Tire (A) Tire Size : The tire size code is a combination of letters and numbers used to define a particular tire's width, height, aspect ratio, construction type, and service description.
(F) Uniform Tire Quality Grading (UTQG) : T ire manufacturers are required to grade tires based on three performance factors: treadwear , traction, and temperature resistance . For more information, see Uniform Tire Quality Grading on page 6 ‑ 73 . (G) Maximum Cold Inflation Load Limit : Maximum load that can be carried and the maximum pressure needed to support that load.
(B) TPC Spec (Tire Performanc e Criteria Specification) : Original equipment tires designed to GM's specific tire performance criteria have a TPC specification code molded onto the sidewall. GM's TPC specifications meet or exceed all federal safety guidelines.
Tire Size The following examples show the different parts of a tire size. Passenger (P ‐ Metric) Tire (A) Passenger (P ‐ Metric) Tire : The United States version of a metric tire sizing system. The letter P as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U.
Light T ruck (L T ‐ Metric) Tire (A) Light T ruck (L T ‐ Metric) Tire : The United States version of a metric tire sizing system. The letters L T as the first two characters in the tire size means a light truck tire engineered to standards set by the U.
Tire T erminology and Definitions Air Pressure : The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight : This means the combined weight of optional accessories.
Intended Outboard Sidewall : The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa) : The metric unit for air pressure. Light T ruck (L T ‐ Metric) Tire : A tire used on light duty trucks and some multipurpose passenger vehicles.
Speed Rating : An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. T raction : The friction between the tire and the road surface. The amount of grip provided. T read : The portion of a tire that comes into contact with the road.
If your tires have too much air (over ‐ infla tion), you can get the following: . Unusual wear . Poor handling . Rough ride . Needless damage from road hazards A vehicle specific T ire and Loading Information label is attached to your vehicle. This label shows your vehicle's original equipment tires and the correct inflation pressures for your tires when they are cold.
If you overfill the tire, release air by pushing on the metal stem in the center of the tire valve. Recheck the tire pressure with the tire gage. Be sure to put the valve caps back on the valve stems. They help prevent leaks by keeping out dirt and moisture.
replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly . See Tire Pressure Monitor Operation on page 6 ‑ 65 for additional information. Federal Communications Commission (FCC) and Industry and Science Canada See Radio Frequency Statement on page 8 ‑ 19 for information regarding Part 15 of the Federal Communications Commission (FCC) Rules and RSS-210/21 1 of Industry and Science Canada.
The low tire pressure warning light may come on in cool weather when the vehicle is first started, and then turn off as you start to drive. This could be an early indicator that the air pressure in the tire(s) are getting low and need to be inflated to the proper pressure.
. One or more TPMS sensors are missing or damaged. The DIC message and the TPMS malfunction light should go off when the TPMS sensors are installed and the sensor matching process is performed successfully . See your dealer/retailer for service. . Replacement tires or wheels do not match your vehicle's original equipment tires or wheels.
Y ou have two minutes to match the first tire/wheel position, and five minutes overall to match all four tire/ wheel positions. If it takes longer than two minutes, to match the first tire and wheel, or more than five minutes to match all four tire and wheel positions the matching process stops and you need to start over .
The purpose of a regular tire rotation is to achieve a uniform wear for all tires on the vehicle. This will ensure that your vehicle continues to perform most like it did when the tires were new . Any time you notice unusual wear , rotate your tires as soon as possible and check wheel alignment.
Make sure the spare tire is stored securely . Push, pull, and then try to rotate or turn the tire. If it moves, tighten the cable. See Storing a Flat or Spare Tire and T ools on page 6 ‑ 92 . When It Is Time for New T ires V arious factors, such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions, influence when you need new tires.
Buying New Tires GM has developed and matched specific tires for your vehicle. The original equipment tires installed on your vehicle, when it was new , were designed to meet General Motors Tire Performance Criteria Specification (TPC spec) system rating.
{ W ARNING: If you use bias-ply tires on the vehicle, the wheel rim flanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly , causing a crash. Use only radial-ply tires with the wheels on the vehicle. If you must replace your vehicle's tires with those that do not have a TPC Spec number , make sure they are the same size, load range, speed rating, and construction type (radial and bias ‐ belted tires) as your vehicle's original tires.
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: T readwear 200 T raction AA T emperature A The following information relates to the system developed by the United States National Highway T raffic Safety Administration (NHTSA), which grades tires by treadwear , traction, and temperature performance.
T raction – AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete.
Y our dealer/retailer will know the kind of wheel you need. Each new wheel should have the same load-carrying capacity , diameter , width, offset, and be mounted the same way as the one it replaces. If you need to replace any of your wheels, wheel bolts, wheel nuts, or T ire Pressure Monitor System (TPMS) sensors, replace them only with new GM original equipment parts.
Tire Chains { W ARNING: If your vehicle has P265/65R18 or P275/55R20 size tires, do not use tire chains. They can damage your vehicle because there is not enough clearance. T ire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts.
If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle's tires properly . If air goes out of a tire, it is much more likely to leak out slowly . But if you should ever have a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire creates a drag that pulls the vehicle toward that side.
Changing a Flat Tire If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 4 ‑ 3 . { W ARNING: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people.
A. Wheel Block B. Flat T ire The following information explains how to use the jack and change a tire. Removing the Spare Tire and T ools The jack and the wheel blocks are located under a cover near the passenger side rear seat. Rear Seat (Passenger Side) Jack Cover 1.
A. Wheel Blocks B. Jack Knob C. Wing Nut D. Retaining Hook E. Jack F . Mounting Bracket 2. Release the jack (E) from the mounting bracket (F) by turning the jack knob (B) on the jack counterclockwise to release the jack from the mounting bracket. 3. Remove the wheel blocks (A) attached to the jack (E) by turning the wing nut (C) counterclockwise.
T o access the spare tire: A. Spare T ire (V alve Stem Pointed Down) B. Hoist Assembly C. Hoist Cable D. T ire/Wheel Retainer E. Hoist Shaft F . Hoist End of Extension T ool G. Hoist Shaft Access Hole H. Wheel Wrench I. Jack Handle Extension(s) J. Spare Tire Lock 1.
4. Insert the open end of the extension (F) through the hole in the rear bumper (G) (hoist shaft access hole). Be sure the hoist end (F) of the extension connects to the hoist shaft (E). The ribbed square end of the extension is used to lower the spare tire.
7. T ilt the tire with slack in the cable to access the tire/wheel retainer (D). Separate the retainer from the guide pin by sliding the retainer up the pin while pressing down on the latch. When the retainer is separated from the guide pin, tilt the retainer and pull it through the center of the wheel along with the cable and guide pin.
Removing the Flat Tire and Installing the Spare Tire Use the following pictures and instructions to remove the flat tire and raise the vehicle. The tools needed are the jack (A), the wheel blocks (B), the jack handle (C), the jack handle extensions (D), and the wheel wrench (E).
3. Use the wheel wrench to loosen all the wheel nuts. T urn the wheel wrench counterclockwise to loosen the wheel nuts. Do not remove the wheel nuts yet. Jacking Locations (Overall View) A. Front Position B. Rear Position { W ARNING: Getting under a vehicle when it is jacked up is dangerous.
Front Position Front Tire Flat: If the flat tire is on a front tire of the vehicle, you will need to use the jack handle and only one jack handle extension. Attach the wheel wrench to the jack handle extension. Attach the jack handle to the jack (A). Position the jack on the frame behind the flat tire near the front body mount as shown.
5. Remove all the wheel nuts. 6. T ake off the flat tire. { W ARNING: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
{ W ARNING: Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle's wheel could fall off, causing a crash. 9. Put the wheel nuts back on with the rounded end of the nuts toward the wheel after mounting the spare tire.
When you reinstall the full-size wheel and tire, you must also reinstall the either the center cap or the bolt-on hub cap, depending on what your vehicle has. . If you are reinstalling a center cap, line up the tab on the center cap with the slot on the wheel.
3. Loosen the cable by turning the wrench counterclockwise three or four turns. 4. Repeat this procedure at least two times. If the spare tire lowers to the ground, continue with Step 5 of Removing the Spare Tire and T ools on page 6 ‑ 79 . 5. If the spare does not lower , turn the wrench counterclockwise until approximately 6 inches (15 cm) of cable is exposed.
9. Position the center lift point of the jack under the center of the spare tire. 10. T urn the wrench clockwise to raise the jack until it lifts the end fitting. 1 1. Continue raising the jack until the spare tire stops moving upward and is held firmly in place.
Storing a Flat or Spare Tire and T ools { W ARNING: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury . In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
1. Put the tire (A) on the ground at the rear of the vehicle with the valve stem pointed down, and to the rear . 2. T ilt the tire. Separate the tire/wheel retainer (D) from the guide pin. Pull the pin through the center of the wheel. T ilt the retainer down through the center wheel opening.
3. Assemble the two jack handle extensions (I) and wheel wrench (H) as shown. 4. Insert the open end of the extension (F) through the hole in the rear bumper (G) (hoist shaft access hole). 5. Raise the tire part way upward. Make sure the retainer is fully seated across the underside of the wheel and is centered in the wheel opening.
8. Reinstall the spare tire lock. 9. Close the hoist shaft access cover . T o store the tools, follow these steps: 1. Return the tools to the tool bag and place it back in the top ‐ box storage unit. 2. Assemble the wheel blocks and jack together with the wing nut by reversing Step 2 under Removing the Spare Tire and T ools on page 6 ‑ 79 3.
Appearance Care Interior Cleaning The vehicle's interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on the upholstery . Dirt can damage carpet, fabric, leather , and plastic surfaces.
. Laundry detergents or dishwashing soaps with degreasers can leave residue that streaks and attracts dirt. For liquid cleaners, about 20 drops per gallon (3.78 L) of water is a good guide. Use only mild, neutral-pH soaps. . T oo much cleaner that saturates the upholstery .
Leather A soft cloth dampened with water can be used to remove dust. If a more thorough cleaning is necessary , a soft cloth dampened with a mild soap solution can be used. Allow the leather to dry naturally . Do not use heat to dry . Never use steam to clean leather .
Weatherstrips Silicone grease on weatherstrips will make them last longer , seal better , and not stick or squeak. Apply silicone grease with a clean cloth. During very cold, damp weather frequent application may be required. See Recommended Fluids and Lubricants on page 7 ‑ 1 1 .
Finish Care Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint finish. Approved cleaning products can be obtained from your dealer/retailer . If the vehicle has a basecoat/clearcoat paint finish, the clearcoat gives more depth and gloss to the colored basecoat.
Aluminum or Chrome-Plated Wheels and T rim The vehicle may have either aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water . Rinse with clean water. After rinsing thoroughly , dry with a soft clean towel.
Tires T o clean the tires, use a stiff brush with tire cleaner . Notice: Using petroleum-based tire dressing products on the vehicle may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on the vehicle.
V ehicle Identification V ehicle Identification Number (VIN) This legal identifier is in the front corner of the instrument panel, on the driver side. It can be seen through the windshield from outside. The VIN also appears on the Certification/T ire and Service Parts labels and certificates of title and registration.
Electrical System Add-On Electrical Equipment Notice: Do not add anything electrical to the vehicle unless you check with your dealer/retailer first. Some electrical equipment can damage the vehicle and the damage would not be covered by the vehicle's warranty .
Instrument Panel Fuse Block The instrument panel fuse block access door is located on the driver side edge of the instrument panel. Pull off the cover to access the fuse block.
Fuses Usage 9 Passenger Door Module, Driver Unlock 10 Power Door Lock 2 (Unlock Feature) 1 1 Power Door Lock 2 (Lock Feature) 12 Stoplamps, Center-High Mounted Stoplamp 13 Rear Climate Controls 14 Pow.
Center Instrument Panel Fuse Block The center instrument panel fuse block is located underneath the instrument panel, to the left of the steering column.
Underhood Fuse Block The underhood fuse block is located in the engine compartment, on the driver side of the vehicle. Lift the cover for access to the fuse/relay block. Notice: Spilling liquid on any electrical components on the vehicle may damage it.
Fuses Usage 1 Right T railer Stop/T urn Lamp 2 Electronic Stability Suspension Control, Automatic Level Control Exhaust 3 Left T railer Stop/T urn Lamp 4 Engine Controls 5 Engine Control Module, Throt.
Fuses Usage 30 Passenger Side High-Beam Headlamp 31 Daytime Running Lamps (DRL) 32 Driver Side High-Beam Headlamp 33 Daytime Running Lights 2 34 Sunroof 35 Key Ignition System, Theft Deterrent System .
J-Case Fuses Usage 57 Cooling Fan 1 58 Automatic Level Control Compressor 59 Heavy Duty Antilock Brake System 60 Cooling Fan 2 61 Antilock Brake System 1 62 Starter 63 Stud 2 (Trailer Brakes) 64 Left .
Capacities and Specifications The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 7 ‑ 1 1 for more information. Application Capacities English Metric Air Conditioning Refrigerant R134a For the air conditioning system refrigerant charge amount, see the refrigerant caution label located under the hood.
Engine Specifications Engine VIN Code T ransmission Spark Plug Gap 5.3L V8 Flexible Fuel with Active Fuel Management ™ (Iron) (LMG) 0 Automatic 0.040 in (1.
2 NOTES 6-1 14.
Section 7 Maintenance Schedule Maintenance Schedule .. ............... ........... 7-2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Scheduled Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Owner Checks and Services .
Maintenance Schedule Introduction Notice: Maintenance intervals, checks, inspections, recommended fluids, and lubricants are necessary to keep this vehicle in good working condition. Damage caused by failure to follow scheduled maintenance might not be covered by the vehicle warranty .
At your General Motors dealer/retailer , you can be certain that you will receive the highest level of service available. Y our dealer/retailer has specially trained service technicians, uses genuine GM replacement parts, as well as, up to date tools and equipment to ensure fast and accurate diagnostics.
When the Change Engine Oil Soon message displays, certain services, checks, and inspections are required. The services described for Maintenance I should be performed at every engine oil change. The services described for Maintenance II should be performed when: .
. Body hinges and latches, key lock cylinders, folding seat hardware, midgate hinges, and tailgate hinges, linkage, and handle pivot points lubrication. See Recommended Fluids and Lubricants on page 7 ‑ 1 1 . More frequent lubrication may be required when vehicle is exposed to a corrosive environment.
. Accelerator pedal check for damage, high effort, or binding. Replace if needed. . Hood support gas strut inspection for signs of wear , corrosion, cracks, loss of lubricant, or other damage. Check the hold open ability of the gas strut. If necessary , replace with genuine parts from your dealer/retailer .
First Engine Oil Change After Every 160 000 km/100,000 Miles . Automatic transmission fluid change (normal service). See Automatic T ransmission Fluid on page 6 ‑ 22 . . Four ‐ wheel drive only: Transfer case fluid change (normal service). Check vent hose at transfer case for kinks and proper installation.
Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and filter . Reset oil life system. • • Engine coolant level check. • • Windshield washer fluid level check. • • T ire inflation pressures check. • • T ire wear inspection.
Owner Checks and Services Starter Switch Check { W ARNING: When you are doing this inspection, the vehicle could move suddenly . If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle.
Ignition T ransmission Lock Check While parked, and with the parking brake set, try to turn the ignition to LOCK/OFF in each shift lever position. . The ignition should turn to LOCK/OFF only when the shift lever is in P (Park). . The ignition key should come out only in LOCK/OFF .
Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number , or specification can be obtained from your dealer/retailer . Usage Fluid/Lubricant Engine Oil Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol.
Usage Fluid/Lubricant Front Axle SAE 80W-90 Axle Lubricant (GM Part No. U.S. 89021671, in Canada 89021672). Rear Axle SAE 75W-90 Synthetic Axle Lubricant (GM Part No. U.S. 89021677, in Canada 89021678) meeting GM Specification 99861 15. T ransfer Case DEXRON ® -VI Automatic T ransmission Fluid.
Maintenance Replacement Parts Replacement parts identified below by name, part number , or specification can be obtained from your dealer/retailer . Maintenance Replacement Parts Part GM Part Number ACDelco Part Number Engine Air Cleaner /Filter Standard Filter 15908916* A3086C* High Capacity Filter 15908915 A3085C Oil Filter 5.
Engine Drive Belt Routing 7-14.
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided.
Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed 7-16.
Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed 7-17.
Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed 7-18.
Section 8 Customer Assistance Information Customer Assistance and Information . . . . . . . . . . . 8-2 Customer Satisfaction Procedure . . . . . . . . . . . . . . . 8-2 Online Owner Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Customer Assistance for T ext T elephone (TTY) Users .
Customer Assistance and Information Customer Satisfaction Procedure Y our satisfaction and goodwill are important to your dealer and to Chevrolet. Normally , any concerns with the sales transaction or the operation of the vehicle will be resolved by the dealer's sales or service departments.
STEP THREE — U.S. Owners : Both General Motors and your dealer are committed to making sure you are completely satisfied with your new vehicle. However , if you continue to remain unsatisfied after following the procedure outlined in Steps One and T wo, you can file with the Better Business Bureau (BBB) Auto Line Program to enforce your rights.
STEP THREE — Canadian Owners : In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps 1 and 2, General Motors of Canada Limited wants you to be aware of its participation in a no-charge Mediation/ Arbitration Program.
Online Owner Center Online Owner Center (U.S.) — www .gmownercenter .com/chevrolet Information and services customized for your specific vehicle — all in one convenient place. . Digital owner manual, warranty information, and more . Online service and maintenance records .
Customer Assistance for T ext T elephone (TTY) Users T o assist customers who are deaf, hard of hearing, or speech-impaired and who use T ext T elephones (TTYs), Chevrolet has TTY equipment available at its Customer Assistance Center . Any TTY user in the U.
Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) — Customer Assistance General Motors de Mexico, S. de R.L. de C.V . Customer Assistance Center Paseo de la Reforma # 2740 Col. Lomas de Bezares C.P .
Calling for Assistance When calling Roadside Assistance, have the following information ready: . Y our name, home address, and home telephone number . T elephone number of your location . Location of the vehicle . Model, year , color , and license plate number of the vehicle .
Services Not Included in Roadside Assistance . Impound towing caused by violation of any laws. . Legal fines. . Mounting, dismounting or changing of snow tires, chains, or other traction devices. . T owing or services for vehicles driven on a non-public road or highway .
Scheduling Service Appointments When your vehicle requires warranty service, contact your dealer/retailer and request an appointment. By scheduling a service appointment and advising your service consultant of your transportation needs, your dealer/retailer can help minimize your inconvenience.
Public T ransportation or Fuel Reimbursement If your vehicle requires overnight warranty repairs, and public transportation is used instead of the dealer's shuttle service, the expense must be supported by original receipts and can only be up to the maximum amount allowed by GM for shuttle service.
Collision Parts Genuine GM Collision parts are new parts made with the same materials and construction methods as the parts with which your vehicle was originally built. Genuine GM Collision parts are your best choice to ensure that your vehicle's designed appearance, durability , and safety are preserved.
Insuring Y our V ehicle Protect your investment in your GM vehicle with comprehensive and collision insurance coverage. There are significant differences in the quality of coverage afforded by various insurance policy terms. Many insurance policies provide reduced protection to your GM vehicle by limiting compensation for damage repairs by using aftermarket collision parts.
. Gather the important information you will need from the other driver . Things like name, address, phone number , driver's license number , vehicle license plate, vehicle make, model and model year , V ehicle Identification Number (VIN), insurance company and policy number , and a general description of the damage to the other vehicle.
Reporting Safety Defects Reporting Safety Defects to the United States Government If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying General Motors.
Reporting Safety Defects to General Motors In addition to notifying NHTSA (or T ransport Canada) in a situation like this, please notify General Motors. Call 1-800-222-1020, or write: Chevrolet Motor Division Chevrolet Customer Assistance Center P .O.
Current and Past Model Order Forms T echnical Service Bulletins and Manuals are available for current and past model GM vehicles. T o request an order form, specify year and model name of the vehicle. ORDER TOLL FREE: 1-800-551-4123 Monday-Friday 8:00 AM - 6:00 PM Eastern Time For Credit Card Orders Only (VISA-MasterCard-Discover), visit Helm, Inc.
Event Data Recorders This vehicle has an Event Data Recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an airbag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle's systems performed.
OnStar ® If the vehicle has OnStar and you subscribe to the OnStar services, please refer to the OnStar T erms and Conditions for information on data collection and use. Navigation System If your vehicle has a navigation system, use of the system may result in the storage of destinations, addresses, telephone numbers, and other trip information.
2 NOTES 8-20.
A Accessories and Modifications . . . . . . . . . . . . . . . . . . . . . . . 6-3 Accessory Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33 Accessory Power Outlets . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15 Active Fuel Management ™ .
Appearance Care (cont.) Sheet Metal Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-102 T ires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-102 Underbody Maintenance . . . . . . . . . . .
C Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-55 California Perchlorate Materials Requirements . . . . . . . . . . . . . . . 6-4 W arning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning (cont.) Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-96 Leather . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-98 T ires . . . . . . . . . . . . . .
Door Delayed Locking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 1 Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10 Power Locks . . . . . . . . . . . . . . . . . . . . . .
Engine (cont.) Oil Pressure Gage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-39 Overheated Protection Operating Mode . . . . . . . . . . 6-33 Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuses Center Instrument Panel Fuse Block . . . . . . . . . . . . . 6-107 Fuses and Circuit Breakers . . . . . . . . . . . . . . . . . . . . . . 6-104 Instrument Panel Fuse Block . . . . . . . . . . . . . . . . . . . . 6-105 Underhood Fuse Block . . . .
I Ignition Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32 Infants and Y oung Children, Restraints . . . . . . . . . . . . 2-40 Inflation - T ire Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-62 Instrument Panel Brightness .
Lights (cont.) Fog Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-40 High/Low Beam Changer . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Highbeam On . . . . . . . . . . . . . . . . . . . . . . . . . . .
N Navigation System, Privacy . . . . . . . . . . . . . . . . . . . . . . . . 8-19 Navigation/Radio System, see Navigation Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 14 New V ehicle Break-In . . . . .
Passenger Airbag Status Indicator . . . . . . . . . . . . . . . . . 4-29 Passenger Sensing System . . . . . . . . . . . . . . . . . . . . . . . 2-71 Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 1 Perchlorate Materials Requirements, California .
Recovery Hooks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-31 Recreational V ehicle T owing . . . . . . . . . . . . . . . . . . . . . . . 5-39 Reimbursement Program, GM Mobility . . . . . . . . . . . . . . . 8-7 Remote Keyless Entry (RKE) System .
Seats (cont.) Power Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Rear Seat Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13 Reclining Seatbacks . . . . . . . . . . . . . . . . . . . .
Storage Areas (cont.) Front Armrest Storage Area . . . . . . . . . . . . . . . . . . . . . . 3-74 Glove Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-74 Roof Rack System . . . . . . . . . . . . . . . . . . . . .
T op-Box Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-91 T ow/Haul Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-42 T ow/Haul Mode Light . . . . . . . . . . . . . . . . . . . . . . . .
W W arning Lights, Gages, and Indicators . . . . . . . . . . . . 4-25 W arnings DIC Warnings and Messages . . . . . . . . . . . . . . . . . . . . . 4-57 Hazard Flashers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Safety and Symbols .
Een belangrijk punt na aankoop van elk apparaat Chevrolet 2010 Avalanche (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Chevrolet 2010 Avalanche heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Chevrolet 2010 Avalanche vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Chevrolet 2010 Avalanche leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Chevrolet 2010 Avalanche krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Chevrolet 2010 Avalanche bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Chevrolet 2010 Avalanche kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Chevrolet 2010 Avalanche . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
