Gebruiksaanwijzing /service van het product 40315 van de fabrikant Chicago Electric
Ga naar pagina of 20
7" PORT ABLE WET CUTTING TILE SA W Model 40315 SET UP AND OPERA TING INSTRUCTIONS Please Note: Diamond Blade not included, sold separately . Visit our website at: http://www .harborfreight.com Read this material before using this product. Failure to do so can result in serious injury .
Page 2 SKU 40315 For technical questions, please call 1-800-444-3353. SA VE THIS MANUAL Keep this manual for the safety warn- ings and precautions, assembly , operat- ing, inspection, maintenance and cleaning procedures.
Page 3 SKU 40315 For technical questions, please call 1-800-444-3353. plugs with grounded power tools. Unmodied plugs and matching out - lets will reduce risk of electric shock. b. A void body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators.
Page 4 SKU 40315 For technical questions, please call 1-800-444-3353. do the job better and safer at the rate for which it was designed. b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be con- trolled with the switch is dangerous and must be repaired.
Page 5 SKU 40315 For technical questions, please call 1-800-444-3353. 4. Use tools with the lowest vibration when there is a choice between dif- ferent processes. 5. Include vibration-free periods each day of work. 6. Grip tool as lightly as possible (while still keeping safe control of it).
Page 6 SKU 40315 For technical questions, please call 1-800-444-3353. 14. POWER CORD 120 VOL T , GROUNDED ELECTRICAL OUTLET TILE SA W DRIP LOOP Figure 1 Always arrange a “drip loop” in the Power Cord/Plug (34) connecting the Tile Saw to a 120 volt, ground- ed, electrical outlet.
Page 7 SKU 40315 For technical questions, please call 1-800-444-3353. 27. Never attempt to remove material stuck in the moving parts of the Tile Saw while it is plugged in and running. 28. When cutting a large work piece make sure its entire length is prop- erly supported.
Page 8 SKU 40315 For technical questions, please call 1-800-444-3353. situations that may occur . It must be understood by the operator that common sense and caution are fac- tors which cannot be built into this product, but must be supplied by the operator .
Page 9 SKU 40315 For technical questions, please call 1-800-444-3353. cause injury beyond immediate area of operation. 1 1. Position the cord clear of the spin- ning blade. If you lose control, the cord may be cut or snagged and your hand or arm may be pulled into the spinning accessory .
Page 10 SKU 40315 For technical questions, please call 1-800-444-3353. GROUNDING TO PREVENT ELECTRIC SHOCK AND DEA TH FROM INCORRECT GROUNDING WIRE CONNECTION: Check with a qualied electrician if you are in doubt as to whether the outlet is properly grounded.
Page 1 1 SKU 40315 For technical questions, please call 1-800-444-3353. 2. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. (See Outlets for 2-Prong Plug.) Extension Cords 1. Grounded tools require a three wire extension cord.
Page 12 SKU 40315 For technical questions, please call 1-800-444-3353. SPECIFICA TIONS Blade Diameter (Blade Not Included, Sold Separately) 7" (67393 7” Continuous Rim Diamond Blade Recommended.
Page 13 SKU 40315 For technical questions, please call 1-800-444-3353. ing sure no hidden electric cords or cables are in the drilling path. 6. Once the mounting holes are drilled, align the four 7/16” wide x 3-1/2” long mounting slots in the base of the Inner Cover (16) with the four pre- drilled mounting holes in the work- bench.
Page 14 SKU 40315 For technical questions, please call 1-800-444-3353. OPERA TING INSTRUCTIONS Read the ENTIRE IMPORT ANT SAFETY INFORMA TION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
Page 15 SKU 40315 For technical questions, please call 1-800-444-3353. General Operating Instructions 1. Fill T ray (17) with water and carefully slide T ray under Blade. Make sure water level is deep enough to cover lower edge of Cutting Wheel Blade, but not so deep as to spill over edge of T ray .
Page 16 SKU 40315 For technical questions, please call 1-800-444-3353. MAINTENANCE AND SER VICING Procedures not specically explained in this manual must be performed only by a qualied technician.
Page 17 SKU 40315 For technical questions, please call 1-800-444-3353. (not included, sold separately), making sure to install Blade according to indicated rotation direction on Blade. F. Replace the Outside Flange (7) and Nut (4). Use the Spanner (59) to hold the Outside Flange (7) while you tighten the Nut (4) securely with the Nut Driver (60).
Page 18 SKU 40315 For technical questions, please call 1-800-444-3353. P ARTS LIST Part Description Part Description Part Description 1 Front Cover 21 Power Switch 41 Motor Lead Wire 2 Screw (M4x10) 2.
Page 19 SKU 40315 For technical questions, please call 1-800-444-3353. ASSEMBL Y DIAGRAM Record Product’ s Serial Number Here: Note: If product has no serial number , record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts .
Page 20 SKU 40315 For technical questions, please call 1-800-444-3353. 90 Day W arranty Harbor Freight T ools Co. makes every effort to assure that its products meet high quality and durability standa.
Een belangrijk punt na aankoop van elk apparaat Chicago Electric 40315 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Chicago Electric 40315 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Chicago Electric 40315 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Chicago Electric 40315 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Chicago Electric 40315 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Chicago Electric 40315 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Chicago Electric 40315 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Chicago Electric 40315 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
