Gebruiksaanwijzing /service van het product 68887 van de fabrikant Chicago Electric
Ga naar pagina of 28
.
Page 2 For technical questions, please call 1-800-444-3353. SKU 68887 T able of Contents Safety ......................................................... 2 Specifications ............................................. 7 Setup ..........................
Page 3 For technical questions, please call 1-800-444-3353. SKU 68887 Fume and Gas Safety FUMES AND GASES can be hazardous to your health. 1. Exposure to welding or cutting exhaust fumes can increase the risk of developing certain cancers, such as cancer of the larynx and lung cancer .
Page 4 For technical questions, please call 1-800-444-3353. SKU 68887 Electrical Safety ELECTRIC SHOCK can KILL. 1. T urn off, disconnect power , and discharge electrode to ground before setting down torch/electrode holder and before service. 2. Do not touch energized electrical parts.
Page 5 For technical questions, please call 1-800-444-3353. SKU 68887 W elder use and care 1. Do not use the welder if the switch does not turn it on and off.
Page 6 For technical questions, please call 1-800-444-3353. SKU 68887 Grounding TO PREVENT ELECTRIC SHOCK AND DEA TH FROM INCORRECT GROUNDING WIRE CONNECTION: Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded.
Page 7 For technical questions, please call 1-800-444-3353. SKU 68887 Specifications Electrical Rating 120V~ / 20A Welding Output 60 ~ 120 A, AC Capacity 18 gauge (0.048″) to 3/16″ (0.19″) mild steel only Not for welding aluminum or stainless steel Duty Cycle 20% @ 90A (See explanation on page 14) Open Circuit V oltage 27 K VA 2.
Page 8 For technical questions, please call 1-800-444-3353. SKU 68887 1. T urn the Welder to OFF and unplug it before proceeding. 2. Press in the pin at the top center of the control panel and open the cover . 3. Remove the Knob, Spring and the T op Plate.
Page 9 For technical questions, please call 1-800-444-3353. SKU 68887 6. T urn the Feed T ensioner counterclockwise to loosen it enough to pull it up, releasing tension. Swing the Feed Swing Arm out. (Note: Do not loosen the Feed T ensioner too much, or it will come apart.
Page 10 For technical questions, please call 1-800-444-3353. SKU 68887 W ARNING The following steps require applying power to the welder with the cover open. T o prevent serious injury from fire or electric shock: 1. Do not touch anything, especially not the Ground Clamp, with the Gun or welding wire or an arc will be ignited.
Page 1 1 For technical questions, please call 1-800-444-3353. SKU 68887 16. T o check the wire’s drive tension, feed the wire against a piece of wood from 2 to 3 inches away . If the wire stops instead of bending, turn the welder to OFF , unplug it, slightly tighten the Feed T ensioner clockwise , and try again.
Page 12 For technical questions, please call 1-800-444-3353. SKU 68887 Basic Welding Read the ENTIRE IMPORT ANT SAFETY INFORMA TION section at the beginning of this manual including all text under subheadings therein before welding.
Page 13 For technical questions, please call 1-800-444-3353. SKU 68887 Control Panel Layout ON MIN OFF MAX WIRE FEED SPEED GUN GROUND 120V~ 60Hz 20A 90 AMP FLUX WIRE WELDER I T EM 68887 Wire .
Page 14 For technical questions, please call 1-800-444-3353. SKU 68887 W eld Settings Chart NOTE: The numbers within the spaces are the approximate wire feed settings recommended* for this wire size and material thickness. Material Thickness (Steel) 18 Gauge 16 Gauge 14 Gauge 1 / 8 ″ 3 / 16 ″ MIN current MAX current .
Page 15 For technical questions, please call 1-800-444-3353. SKU 68887 1. Make practice welds on pieces of scrap the same thickness as your intended workpiece to practice technique before welding anything of value.
Page 16 For technical questions, please call 1-800-444-3353. SKU 68887 1. Press (and hold) T rigger and contact area to be welded with electrode wire to ignite arc. 2. For a narrow weld, you can usually draw the wire in a steady straight line, this is called a stringer bead .
Page 17 For technical questions, please call 1-800-444-3353. SKU 68887 Note: If Welder is used too long, the amber Overload Indicator will light and the Welder Gun will shut of f until the welder cools. If this happens, rest the Gun on an electrically non-conductive, heat-resistant surface, such as a concrete slab, well clear of the ground clamp.
Page 18 For technical questions, please call 1-800-444-3353. SKU 68887 A good way to test welding technique is to examine a weld’s appearance after it has cooled and the slag has been removed. Then, better welding can be learned by adjusting your weld technique to remedy any problems found.
Page 19 For technical questions, please call 1-800-444-3353. SKU 68887 Weld Diagnosis W orkpiece Heat Control / W eld Penetration EXCESS PENETRA TION OR BURN-THROUGH PROPER PENETRA TION INADEQUA TE PE.
Page 20 For technical questions, please call 1-800-444-3353. SKU 68887 W eld Not Adhering Properly Gaps present between weld and previous bead or between weld and workpiece. See areas below . POSSIBLE CAUSES AND SOLUTIONS 1. Incorrect welding technique: Place stringer bead at correct place in joint.
Page 21 For technical questions, please call 1-800-444-3353. SKU 68887 Coat of Slag Over W eld Slag is a necessary part of a flux- core wire weld. It shields the weld from impurities. Clean off the slag with the Chipping Hammer and Wire Brush after welding.
Page 22 For technical questions, please call 1-800-444-3353. SKU 68887 Maintenance TO PREVENT SERIOUS INJUR Y , FIRE AND BURNS: Unplug the Welder , rest the Gun on a heat-proof, electrically non-conductive surface, and allow all parts of the Welder to cool thoroughly before service.
Page 23 For technical questions, please call 1-800-444-3353. SKU 68887 Contact T ip Inspection, Cleaning, and Replacement 1. Make sure that the entire Gun is completely cool and that the Power Cord is unplugged from the electrical outlet before proceeding.
Page 24 For technical questions, please call 1-800-444-3353. SKU 68887 T roubleshooting IMPORT ANT! Be CERT AIN to shut off the Welder , disconnect it from power , and discharge the Gun to ground before adjusting, cleaning, or repairing the unit. Wire Feed Motor Runs But W ire Does Not Feed Properly POSSIBLE CAUSES AND SOLUTIONS 1.
Page 25 For technical questions, please call 1-800-444-3353. SKU 68887 TROUBLESHOOTING (continued) IMPORT ANT! Be CERT AIN to shut off the Welder , disconnect it from power , and discharge the Gun to ground before adjusting, cleaning, or repairing the unit.
Page 26 For technical questions, please call 1-800-444-3353. SKU 68887 Parts Lists and Diagrams Wiring Schematic R MAX S2 S1 T1 MIN B b Q A C 1 1 2 3 2 3 4 J G 1 2 3 4 24V Parts List 1 Grounding Cable.
Page 27 For technical questions, please call 1-800-444-3353. SKU 68887 Part 9 Detail .030″ 9a 9d 9f (hidden by part 9e) 9e 9b 9c Record Product’ s Serial Number Here: Note: If product has no serial number , record month and year of purchase instead.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 9301 1 • (800) 444-3353 Limited 90 Day W arranty Harbor Freight T ools Co. makes every effort to assure that its products meet high quality .
Een belangrijk punt na aankoop van elk apparaat Chicago Electric 68887 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Chicago Electric 68887 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Chicago Electric 68887 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Chicago Electric 68887 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Chicago Electric 68887 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Chicago Electric 68887 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Chicago Electric 68887 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Chicago Electric 68887 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
