Gebruiksaanwijzing /service van het product Pacifica Touring (2005) van de fabrikant Chrysler
Ga naar pagina of 376
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE .............................. 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ...........
I n f o r m a t i o n P r o v i d e d b y :.
INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 䡵 How T o Use This Manual .................. 4 䡵 W arnings And Cautions ................... 6 䡵 V ehicle Identification Number ............... 6 䡵 V ehicle Modifications / Alterations .
INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a W arranty Information Booklet and various customer oriented documents.
INTRODUCTION 5 1 I n f o r m a t i o n P r o v i d e d b y :.
W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es which could result in an accident or bodily injury . It also contains CAUTIONS against procedur es which could result in damage to your vehicle. If you do not read this entir e manual you may miss important information.
VEHICLE MODIFICA TIONS / AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
I n f o r m a t i o n P r o v i d e d b y :.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys .................. 1 1 ▫ Ignition Key Removal ................... 1 1 ▫ Key-In-Ignition Reminder ................ 1 2 䡵 Sentry Key ............................ 1 2 ▫ Replacement Keys .
▫ T o T urn Off “Flash Lights On Lock/Unlock” . . .22 ▫ General Information .................... 2 3 ▫ T ransmitter Battery Service ............... 2 3 䡵 V ehicle Theft Alarm ...................... 2 4 䡵 Liftgate ........................
A WORD ABOUT YOUR KEYS Y ou can insert the double sided keys into the locks with either side up. The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer .
NOTE: The power window switches, radio, power sunroof, and power outlets will remain active for up to 45 seconds after the ignition switch has been turned off. Opening either front door will cancel this feature. W ARNING! Leaving children in a vehicle unattended is danger- ous for a number of reasons.
chip (transponder) embedded into them. Only keys that have been programmed to the vehicle can be used to start and operate the vehicle. The Sentry Key Immobilizer System does not need to be armed or activated. Operation of the system is automatic regar dless of whether or not the vehicle is locked or unlocked.
All of the keys provided with your new vehicle have been programmed to the vehicle electronics. Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it can not be programmed to any other vehicle.
4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds a single chime will sound. The Theft Alarm Light will stop flashing, turn on for 3 seconds; then turn off. The new Sentry Key has been programmed.
DOOR LOCKS Manual Door Locks Lock the doors by pushing up on the lock knob on each door trim panel. If the lock knob is up when you shut the door , the door will lock. Therefor e, make sure the keys are not inside the vehicle before closing the door .
If you press the power door lock switch while the key is in the ignition, and any front door is open, the power locks will not operate. This prevents you from acciden- tally locking your keys in the vehicle. Removing the key or closing the door will allow the locks to operate.
Auto Unlock The doors will unlock automatically on vehicles with power door locks if: 1. The Auto Unlock feature is enabled, 2. the transmission was in gear and the vehicle speed returned to 0 mph (0 km/h), 3. the transmission is in NEUTRAL or P ARK, 4.
T o activate the system, open the rear door and move the child lock control, located near the door’s rear latch, to the ON position. When the child lock system is engaged the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position.
NOTE: If the key is in the ignition switch, then all buttons on that transmitter will be disabled. The buttons on the remaining transmitters will work.
T o lock the doors and liftgate: Press and release the LOCK button on the transmitter to lock all doors and liftgate. The horn will chirp once to acknowledge the signal.
T o Open/Close Power Liftgate — If Equipped Press the LIFTGA TE button twice within five seconds to open/close the power liftgate. The liftgate will beep for 2 seconds and then open/close. If the button is pushed while the liftgate is being power closed, the liftgate will reverse to the full open position.
General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interfer ence r eceived, including interference that may cause undesired op- eration.
2. Remove and replace the battery . A void touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery , clean it with rubbing alcohol. 3. T o reassemble the transmitter case, snap the two halves together .
T o disarm the system: Press the UNLOCK button on the keyless entry transmitter . Also, using a valid sentry key and moving the ignition switch to the ON/ST AR T posi- tion will disarm the system. If you disarm the system and access the liftgate area, the system must be rearmed, as described previously , when closing the liftgate.
The alarm system will be activated when the battery is connected if the system was previously armed. The exterior lights will flash, the horn will sound, and the ignition will not start the vehicle.
be used to open the liftgate. The emergency liftgate latch release can be accessed through a snap-in cover located on the liftgate trim panel. • If the liftgate is locked and is not equipped with a .
W ARNING! During power operation, personal injury or cargo damage may occur . Ensure the liftgate travel path is clear . Make sure the liftgate is closed and latched before driving away .
• If the power liftgate encounters multiple obstructions within the same cycle, the system will automatically stop and must be opened or closed manually . W ARNING! • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle.
The window controls will operate only when the ignition switch is in the ON or ACCESSORY position. The window lock switch on the driver’s door allows you to disable the window controls on the passenger doors.
belts, your seat belts or the LA TCH feature (refer to the Child Restraint section in this manual), can be used to hold infant and child restraint systems. NOTE: The front airbags have a multi stage inflator design. This allows the airbag to have different rates of inflation that are based on collision severity .
The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. But in a collision, the belt will lock and reduce the risk of your striking the inside of the vehicle or being thrown out.
Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door . Sit back and adjust the seat. 2. The seat belt latch plate is near the seatback of the front seats and next to your arm in the rear seats. Grasp the latch plate and pull out the belt.
3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click”. W ARNING! • A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries.
4. Position the lap belt across your thighs, below your abdomen. T o remove slack in the lap belt portion, pull up on the shoulder belt. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
6. T o release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary , slide the latch plate down the webbing to allow the belt to retract fully . W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position.
2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate. 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate.
Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision.
The Enhanced W arning System (BeltAlert) can be en- abled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or RUN position.
Seat Belts and Pregnant Women W e recommend that pregnant women use the seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible.
Driver and Front Passenger Supplemental Restraint System - Airbag This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel.
NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment. W ARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. Y ou may damage the airbags and you could be injured because the airbags are not there to protect you.
Airbags inflate in moderate to high speed impacts. Along with seat belts, and pretensioners, front airbags work with the instrument panel knee blockers to pr ovide improved protection for the driver and front passenger . Left and right side curtain airbags also work with seat belts to improve occupant protection.
If a child from 1 to 12 years old must ride in the front passenger seat because the vehicle is crowded, move the seat as far back as possible, and use the proper child restraint. Refer to the section on Child Restraint. Y ou should read the instructions provided with your child restraint to make sure that you are using it properly .
“The Front Airbag System” consists of the following: • Airbag Control Module (with integrated impact sen- sor) • AIRBAG Readiness Light • Driver Airbag • Front Passenger Airbag • Seat Be.
The airbag control module sends a message to the instrument cluster to turn on the AIRBAG light in the instrument panel for 6 to 8 seconds when the ignition switch is first turned ON, then turns the light off.
the crash side of the vehicle. A quantity of nontoxic gas is generated to inflate the side curtain airbag. The inflating side curtain airbag pushes the outside edge of the headliner out of the way and inflates (in about the same time it takes to blink your eyes).
• Airbag Control Module • Interconnecting W iring If An Airbag Deployment Occurs The airbag systems are designed to deploy when the airbag control modules detect a moderate-to-severe col- lision, to help restrain the driver and front passenger , and then immediately deflate.
W ARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags and seat belt pretensioners replaced by an autho- rized dealer as soon as possible.
Airbag Light Y ou will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately .
W ARNING! In a collision, an unrestrained child, even a tiny baby , can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured.
The tether anchors are located on the rear surface of the seat. Child restraint systems designed to be compatible with the vehicles LA TCH System are now available. LA TCH child restraints make installation into the vehicle simple and convenient. When using the LA TCH System, always follow the child restraint manufactures installation instructions.
T ether Anchors There are tether strap anchorages behind all second row seating positions and the driver’s side third row seating position. The tether anchors are located in the rear surface of the seat.
Infants and Children There are differ ent sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to ensure you have the right seat for your child.
• The belt-positioning booster seat is for children weigh- ing more than 18 kg (40 lbs), but who are still too small to fit the vehicle’s seat belts properly . If the child can not sit with knees bent over the vehicles seat cushion while the child’s back is against the seat back, they should use a belt-positioning booster seat.
that you can install the child restraint in the vehicle where you will use it, before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • Carefully follow the instructions that come with the restraint.
In general, you will first loosen the adjusters on the lower straps and tether straps so that you can more easily attach the hook or connector to the lower anchorages and tether anchorages. Then tighten all three straps as you push the child restraint rearward and downward into the seat.
Children T oo Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably , and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the lap/shoulder belt in a rear seat.
The engine oil installed in the engine at the factory is a high quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur . The r ecommended viscosity and quality grades are shown in Section 7 of this manual.
W ARNING! If you are required to drive with the deck lid/liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. DO NOT use the recirculation mode. Safety Checks Y ou Should Make Inside The V ehicle Seat Belts Inspect the belt system periodically , checking for cuts, frays and loose parts.
Periodic Safety Checks Y ou Should Make Outside The V ehicle T ires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect tread and sidewall for cuts or cracks. Check wheel nuts for tightness, and tires (includ- ing spare) for proper pressure.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors ............................... 6 7 ▫ Inside Day/Night Mirror ................. 6 7 ▫ Automatic Dimming Mirror — If Equipped .... 6 7 ▫ Driver’s Side Outside Mirror Auto Dimmer — If Equipped .
䡵 Seats ................................. 9 3 ▫ 10–W ay Driver’s Power Seat — If Equipped . . .93 ▫ 8–W ay Driver’s Power Seat — If Equipped .... 9 3 ▫ 4–W ay Passenger’s Power Seat ............. 9 3 ▫ Adjustable Head Restraints .
▫ T urn Signals ......................... 1 1 2 ▫ Highbeam/Lowbeam Select Switch ......... 1 1 3 ▫ Passing Light ........................ 1 1 3 䡵 W indshield W ipers And W ashers ........... 1 1 3 ▫ W indshield W ashers ................... 1 1 3 ▫ Mist Feature .
▫ Erasing Homelink Buttons ............... 1 2 7 ▫ Reprogramming a Single Homelink Button . . . 128 ▫ Security ............................ 1 2 8 䡵 Power Sunroof — If Equipped ............. 1 2 9 ▫ Express Open Feature .................. 1 2 9 ▫ W ind Buffeting .
MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window . A two point pivot system allows for horizontal and vertical adjustment of the mirror . Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle).
CAUTION! T o avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror . Apply the solution onto a clean cloth and wipe the mirror clean. Driver’s Side Outside Mirror Auto Dimmer — If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you.
W ARNING! V ehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in this convex mirror .
Power mirror preselected positions can be controlled by the optional Memory Seat Feature. Refer to “Memory Seat” in section 3 of this manual. Heated Remote Control Mirrors These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the Rear W indow Defrost.
HANDS–FREE COMMUNICA TION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone* using simple voice commands (e.g., ⬙ Call ѧ Mike ѧ W ork ⬙ or ⬙ Dial ѧ 248-555-1212 ⬙ ).
The rearview mirror contains the microphone for the system and the control buttons that will enable you to access the system. The diagram below shows the mirror with the appropriate buttons. Individual button behavior is discussed in the ⬙ Operation ⬙ section.
UConnect™ system prompts. Y ou will be prompted for a specific command and then guided through the available options. • Prior to giving a voice command, one must wait for the voice on beep, which follows the ⬙ Ready ⬙ prompt or another prompt.
Pair (Link) UConnect™ System to a Cellular Phone T o begin using your UConnect™ system, you must pair your compatible Bluetooth™ enabled cellular phone (re- fer to ⬙ Introduction ⬙ section to learn about the phone type). T o complete the pairing process, you will need to refer ence your cellular phone owner’s manual.
only one cellular phone can be in use, connected to your UConnect™ System. The priority allows the UConnect™ system to know which cellular phone to use if multiple cellular phones are in the vehicle at the same time.
• After the ⬙ Ready ⬙ prompt and the following beep, say the name of the person you want to call. For example, you can say ⬙ John Doe, ⬙ where John Doe is a previ- ously stored name entry in the UConnect™ phone- book. Refer to section ⬙ Add Names to Y our UCon- nect™ Phonebook, ⬙ to learn how to store a name in the phonebook.
Edit Entries in the UConnect™ Phonebook NOTE: Adding names to phonebook is recommended when vehicle is not in motion. • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Phonebook Edit. ⬙ • Y ou will then be asked for the name of the phonebook entry that you wish to edit.
• After you enter the name, the UConnect™ system will ask you which designation you wish to delete: home, work, mobile or pager . Say the designation you wish to delete. Delete All Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin.
accessed through the UConnect™ system. Check with your cellular service provider for the features that you have. Answer or Reject an Incoming Call - No Call Currently in Progress When you receive a call on your cellular phone, the UConnect™ system will interrupt the vehicle audio system, if on, and will ask if you would like to answer the call.
T oggling Between Calls If two calls are in progress (one active and one on hold), press the ’Phone’ button until you hear a single beep indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at one time.
Call Continuation Call continuation is progr ession of a phone call on UConnect™ system after the vehicle ignition key has been switched to off. Call continuation functionality can be of three types.
Emergency Assistance If you are in an emergency and the mobile phone is reachable: • Pick up the phone and manually dial the emergency number for your area. If the phone is not reachable and the UConnect™ system is operational, you may reach the emergency number as follows: • Press the ’Phone’ button to begin.
V oice Mail Calling T o learn how to access your voice mail, refer to section ⬙ W orking with Automated Systems. ⬙ W orking with Automated Systems This method is designed to be used in instances where one generally has to press numbers on the cellular phone keypad while navigating through an automated tele- phony system.
• Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Confirmations. ⬙ The UConnect™ system will play the current confirmation prompt status and you will be given the choice to change it.
In order to un-mute the UConnect™ system: • Press the ’V oice Recognition’ button. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Mute-off.
• The UConnect™ system will play the phone names of all paired cellular phones in order from the highest to the lowest priority . Select another Cellular Phone This feature allows you to select and start using another phone with the UConnect™ system.
Things Y ou Should Know About Y our UConnect™ System V oice Recognition (VR) • Always wait for the beep before speaking. • Speak normally , without pausing, just as you would speak to a person sitting approximately eight (8) feet away from you. • Make sure that no one other than you is speaking during a voice recognition period.
• Y ou can say ⬙ O ⬙ (letter ⬙ O ⬙ ) for ⬙ 0 ⬙ (zero). ⬙ 800 ⬙ must be spoken ⬙ eight-zero-zer o. ⬙ • Even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported.
Reset In rare instances, it may be necessary to reset the UCon- nect™ system. The reset feature is exercised by pressing and holding the ’UConnect™ ’ and ’V oice Recognition’ buttons simultaneously for 15 seconds. Normally , you do not need to exercise this feature.
90 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 91 3 I n f o r m a t i o n P r o v i d e d b y :.
92 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
SEA TS 10–W ay Driver’s Power Seat — If Equipped The driver’s power seat switches are located on the driver’s front door trim panel. The bottom switch con- trols up/down, forward/r earward, and tilt adjustment. The top switch controls the seatback recline adjustment and the middle switch controls the lumbar adjustment.
CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear .
Press the switch once to select a heat setting (high or low) and press the switch a second time in the same direction to turn the heated seat off. The indicator light will show when LOW or HIGH heat is ON. The controls for the second row heated seats are located on the center console between the seats.
heated seat is not functioning properly and that ser- vice is requir ed. See your authorized dealer for service. • Once a heat setting is selected, heat will be felt within 2 to 3 minutes. • The heated seats will turn off when the ignition switch is turned to the OFF position.
W ARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or fatally injured. Use the recliner only when the vehicle is parked.
W ARNING! Adjust the seat only while the vehicle is parked. Adjusting a seat while the vehicle is moving is dangerous. The seat belt might not be properly adjusted and you could be injured. Second Row Fold & T umble Seats The second row seats can be folded and tumbled forward for easy access to the third seat or rear cargo area.
5. Pull up on the release handle labeled “2” and lift firmly to tumble the seat fully forward. If the seat contacts the rear of the front seat, move the front seat forward. T o relatch the seat, tilt the seat rearwar d and push down firmly to engage the r ear attachments.
1. Pull up on the seatback release handle “1” located on the back of the seat to fold the seatback down. 2. Pull the release strap “2” located at the bottom of the seat to lift and tumble the seat forward. T o relatch the seat, tilt the seat rearwar d and push down firmly to engage the r ear attachments.
Third Row Seating Flexibility The third row seats may be used with either or both seatbacks folded forward for additional storage space. T o fold the seat, remove any objects from in front of or on the seat. Then pull handle located on the seatback and push it forward.
W ARNING! • Not all head restraints in this vehicle are the same. Head restraints from one seating position should not be removed and installed in any other seating position. In a collision, serious injury or death may result if the proper head restraint is not installed on each seat.
NOTE: Be sure to reattach the strap to secure the load floor panel when not in use. Plastic Grocery Bag Retainer Retainer hooks which will hold plastic grocery bag handles are built into the seatbacks of all front seats. The floor supports the partial weight of the bagged goods.
DRIVER MEMOR Y SYSTEM — IF EQUIPPED If your vehicle is equipped with memory systems, your remote keyless entry transmitter or memory seat buttons on the driver’s door panel can be used to recall the driver’s seat, outside mirrors, adjustable pedals (if equipped) and radio station presets to saved positions.
Y our vehicle has been delivered with two remote keyless entry transmitters. One or both transmitters can be linked to either memory position. Up to eight remote keyless entry transmitters can be used with your vehicle.
Repeat the above steps for the second position using the other driver’s door numbered button and Remote Key- less Entry T ransmitter . Each time the SET (S) button and a numbered button are pressed, you erase the old memory and store a new one. T o Disable A T ransmitter Link, Follow These Steps: 1.
TO OPEN AND CLOSE THE HOOD T o open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel. Next, push to the left the safety catch located under the front edge of the hood, near the center .
W ARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Y ou could have a collision. Be sure all hood latches are fully latched before driving. LIGHTS Overhead Console Map/Reading Lights These lights are mounted between the sun visors on the overhead console.
Interior Lights The interior lights come on when a door is opened. The interior lights will automatically turn off in about 15 minutes if a door is left open or the dimmer control is left in the Dome light position. T urn the ignition switch ON to restor e the interior light operation.
Headlights, Parking Lights, Instrument Panel Lights T urn the end of the Multi-Function Lever to the first detent for parking light and instrument panel light operation. T urn to the second detent for headlight, park light and instrument panel light operation.
Parade Mode (Daytime Brightness Feature) Rotate the dimmer control upward to the first detent. This feature brightens the odometer and radio display when the parking lights or headlights are on during daylight conditions. Automatic Headlights This system automatically turns your headlights ON or OFF based on ambient light levels.
T o activate the delay feature, turn off the ignition switch while the headlights are still on. Then turn off the headlights within 45 seconds. The 90 second delay inter- val begins when headlight switch is turned off. If the headlights or park lights are turned back on or the ignition switch is turned on, the delay will be cancelled.
Highbeam/Lowbeam Select Switch Pull the Multi-Function Lever towards you to switch the headlights to HIGH beam. Pull the Lever a second time to switch the headlights to LOW beam. Passing Light Y ou can signal another vehicle with your headlights by lightly pulling the Multi-Function Lever toward you.
If the lever is pulled while in the OFF position, the wipers will operate for two wipe cycles, then turn OFF . Mist Feature Push down on the wiper lever to activate a single wipe to clear off road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate.
Rotating the center of the switch up to the DEL (Delay) position or the ON position will activate the rear wiper . Push the lever forward to initiate the rear wash function in any of the three positions. The washer pump will continue to operate as long as the lever is pressed.
TIL T STEERING COLUMN T o tilt the column, pull the lever , located behind the turn signal control, toward you and move the steering wheel up or down, as desired. Release the lever to lock the steering wheel firmly in place. W ARNING! T ilting the steering column while the vehicle is moving is dangerous.
T o turn the system back ON, press the switch a second time until the traction control Indicator turns OFF . NOTE: • The traction control Indicator comes on each time the ignition switch is turned ON. This will occur even if you used the switch to turn the system OFF .
ADJUST ABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward or away from the driver to provide improved position with the steering wheel. The adjust- able pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position.
CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path.
W ARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. Y ou could accidently set the system or cause it to go faster than you want. Y ou could lose control and have an accident. Always leave the system OFF when you aren’t using it.
is tapped, speed increases so that tapping the button three times will increase speed by 6 mph (10 km/h), etc. T o decrease speed while speed control is set, press and hold the “COAST” button. Release the button when the desired speed is reached, and the new speed will be set.
OVERHEAD CONSOLE — IF EQUIPPED The overhead console can contain courtesy/reading lights, an optional universal garage door opener (HomeLink 威 ), storage for sunglasses, optional power sunroof switches and an optional power liftgate switch. Courtesy/Reading Lights At the forward end of the console are two courtesy/ reading lights.
GARAGE DOOR OPENER — IF EQUIPPED The HomeLink 威 Universal T ransceiver replaces up to three remote controls (hand held transmitters) that oper- ate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button.
Programming HomeLink NOTE: When programming a garage door opener , it is advised to park outside the garage. Some vehicles may requir e the ignition switch to be turned to the second (or ⬙ accessories ⬙ ) position for programming and/or opera- tion of HomeLink.
W ARNING! Y our motorized door or gate will open and close while you are training the Universal T ransceiver . Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects.
If the indicator light blinks rapidly for two seconds and then turns to a constant light continue with ⴖ Program- ming ⴖ steps 6-8 to complete the programming of a rolling code equipped device (most commonly a garage door opener).
If you live in Canada or you are having difficulties programming a gate operator by using the ⬙ Program- ming ⬙ procedures (regardless of where you live), replace ⴖ Programming HomeLink ⴖ step.
Reprogramming a Single HomeLink Button T o program a device to HomeLink using a HomeLink button previously trained, follow these steps: 1. Press and hold the desired HomeLink button. Do NOT release the button. 2. The indicator light will begin to flash after 20 seconds.
POWER SUNROOF — IF EQUIPPED The power sunroof switches are located between the sun visors on the overhead console. Press and hold the switch rearward to fully open the sunroof. The sunroof can be stopped at any position between closed and full open.
and the glass will automatically stop at the comfort stop position. Pressing the switch rearwar d again will fully open the sunroof. During the Express Open operation, any movement of the switch will stop the sunroof and it will remain in a partial open position.
Wind Buffeting W ind buffeting can be described as the perception of pressur e on the ears or a helicopter type sound in the ears. Y our vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.
A third outlet is located on the back of the front center console near the floor , and is also controlled by the ignition switch. A fourth outlet is located on the driver’s side, in the rear cargo area and is also controlled by the ignition switch. The outlets include tethered caps labeled with a key or battery symbol indicating the power source.
CUPHOLDERS Front Seat Cupholders The cupholders are located in the forward edge of the center console. Push down on the forward edge of the console to release the cupholders.
Rear Cargo Storage Bin The storage bin is located in the floor of the rear cargo area. T o open lift up on the handle. Retractable Cargo Area Cover — If Equipped T o cover the cargo area: 1. Fold down the third row seatbacks. 2. Unfold the cargo cover extensions and lock into place.
W ARNING! In an accident a cargo cover loose in the vehicle could cause injury . It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting.
W ARNING! • Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or colli- sion a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers.
ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. Distribute cargo weight evenly on the roof rack crossbars.
CAUTION! • T o avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appro- priately .
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instruments And Controls ................. 1 4 2 䡵 Instrument Cluster ...................... 1 4 3 䡵 Instrument Cluster Descriptions ............ 1 4 4 䡵 Electronic V ehicle Information Center (EVIC) .
▫ Radio Operation ...................... 1 6 6 ▫ T ape Player Operation .................. 1 7 0 ▫ CD Player Operation ................... 1 7 2 ▫ CD/DVD Changer Operation — If Equipped . 173 䡵 6 Disc CD/DVD Changer (Rdv) — If Equipped .
▫ Satellite Antenna ...................... 1 8 9 ▫ Reception Quality ..................... 1 8 9 䡵 Remote Sound System Controls ............. 1 9 0 ▫ Radio Operation ...................... 1 9 0 ▫ T ape Player ......................... 1 9 0 ▫ CD Player .
INSTRUMENTS AND CONTROLS 142 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i o n P r o v i d e d b y :.
INSTRUMENT CLUSTER UNDERST ANDING YOUR INSTRUMENT P ANEL 143 4 I n f o r m a t i o n P r o v i d e d b y :.
INSTRUMENT CLUSTER DESCRIPTIONS 1. V oltage Light This light monitors the electrical system voltage. The light should turn on momentarily as the engine is started. If the light stays on or turns on while driving, it indicates a problem with the charging system.
W ARNING! A hot engine cooling system is dangerous. Y ou or others could be badly burned by steam or boiling coolant. Y ou may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual.
is not functioning and that service is requir ed. However , the conventional brake system will continue to operate normally if the BRAKE warning light is not on. If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes.
V ehicles equipped with Anti-Lock brakes (ABS), are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake W arning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required.
disabled for about 4 minutes until the brakes have cooled. The system will automatically reactivate and turn off the T raction Control Light. 9. T achometer The red segments indicate the maximum permissible engine revolutions-per -minute (r .p.m. x 1000) for each gear range.
release the T rip Odometer button. T o reset a trip odom- eter , display the desired trip odometer to be reset then push and hold the button until the display resets (ap- proximately 2 seconds). 14. Cruise Indicator This display indicator shows that the Speed Control System is ON.
18. Front Fog Light Indicator — If Equipped This light shows the front fog lights are ON. 19. Oil Pressure W arning Light This light shows low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible.
Driving on a significantly underinflated tire causes the tire to overheat and can lead to tire failure. Underinfla- tion also reduces fuel efficiency and tire tread life, and may af fect the vehicle’s handling and stopping ability .
• Compass display — If Equipped • Mini-T rip functions — If Equipped Pressing the MENU button will change the displayed programming features. Pressing the STEP button will display the available choices. Pressing the MENU button a second time accepts a selected choice.
• UNLOCK TO OPEN LIFTGA TE (with a single chime) • PUT IN P ARK FOR LIFTGA TE (with a single chime) • TOO COLD FOR PWR LIFTGA TE (with a single chime) • TOO HOT FOR PWR LIFTGA TE (with a singl.
• 1,2,3 OR 4 TIRE(S) HIGH PRESSURE (Refer to “Start- ing And Operating, T ire Section”) • SER VICE TIRE SYSTEM SOON (Refer to “Starting And Operating, T ire Section”) • TIRE PRESSURE UNA.
Auto Door Locks? When this feature is selected, all doors and the liftgate lock automatically when the speed of the vehicle reaches 15 mph (25 km/h). Pressing the STEP button when in this display will select “Y es” or “No.
flash lights on lock/unlock feature. Pressing the STEP button when in this display will select “Y es” or “No.” Flash Lights On Lock/Unlock? When this feature is selected, the front and rear turn signals will flash when the doors are locked or unlocked using the remote keyless entry transmitter .
Reset Service Distance (Displays Only if Service Interval was Changed) When this feature is selected the current accumulated service distance can be reset to the newly selected service interval. Pressing the STEP button when in this display will select “Y es” or “No.
Automatic Compass Calibration This compass is self calibrating which eliminates the need to manually set the compass. When the vehicle is new , the compass may appear erratic and the EVIC will display “COMP ASS CALIBRA TING” until the compass is calibrated.
T o set the variance: T urn the ignition switch ON and set the display to Compass. Press the RESET button for approximately 5 seconds but no more than 10 seconds. The “COMP ASS V ARIANCE” message and the last vari- ance zone number will be displayed.
• Of f Mode Shows a blank display . • Step Button Push this button to cycle through all the Mini-trip functions. T o Reset The Display Pressing and releasing the Reset button once will clear the resettable function currently being displayed. The resettable function is average fuel economy .
SALES CODE RAH—AM & FM STEREO RADIO WITH CD PLA YER AND CD/DVD CHANGER CONTROLS Radio Operation Power/V olume Control Press the ON/VOL control to turn the radio on. T urn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch.
top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button in will by- pass stations without stopping until you release it. T uning Press the TUNE control up or down to increase or decrease the frequency .
both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into memory . Y ou can recall the stations stored in SET 2 memory by pressing the push- button twice. T o Change From Clock T o Radio Mode Press the TIME button to change the display between radio frequency and time.
If you insert a disc with the ignition ON and the radio OFF , the display will show the time of day . If you insert a disc with the ignition OFF , the display will show the time of day for about 5 seconds, then go out. If the power is ON, the unit will switch from radio to CD mode and begin to play when you insert the disc.
Press the SEEK button to move to the next randomly selected track. Press TUNE FF to fast forward through the tracks. Press the FF button a second time to stop the fast forward feature. If TUNE RW is pr essed, the current track will reverse to the beginning of the track and begin playing.
Radio Operation Power/V olume Control Press the ON/VOL control to turn the radio on. T urn the volume control to the right to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio.
Program T ype Radio Display Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B Sports Sports T alk T alk T op 40 T op 40 W eather W eather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name.
Scan Press and release the SCAN button to search for the next station in either the AM or FM mode. The radio will pause for 5 seconds at each listenable station before continuing to the next. T o stop the search, press the SCAN button a second time. T une Press the TUNE control up or down to increase or decrease the frequency .
SET 1 will now show in the display window . Select the “1–5” button you wish to lock onto this station and press and release that button. If a button is not selected within 5 seconds after pressing the SET button, the station will continue to play but will not be locked into push-button memory .
T ape Player Operation Insert the cassette with the exposed tape side toward the right and the mechanical action of the player will gently pull the cassette into the play position. NOTE: When subjected to extremely cold temperatures, the tape mechanism may require a few minutes to warm up for proper operation.
Rewind — R W Press the R W button down momentarily to reverse the tape direction. The tape will rewind until the button is pressed again or until the beginning of the tape is reached. At the beginning of the tape, the tape will play in the opposite direction.
CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate. Inserting The Compact Disc Y ou may either insert or eject a disc with the radio OFF .
FF/TUNE/R W Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW (Reverse) button works in a similar manner . Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play .
Disc Up/Program Button 1 Press the DISC (button 1) button to play the next avail- able disc. Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play . This feature plays the selections on the currently playing compact disc in random order to provide an interesting change of pace.
6 DISC CD/DVD CHANGER (RDV) — IF EQUIPPED The Rear Seat Audio/V ideo System allows passengers to listen to a CD or DVD from the 6 disc CD/DVD changer through wireless headphones, while the front seat pas- sengers listen to either AM/FM, Cassette or CDs from the radio speakers.
T o insert disc(s) into the changer , follow the instructions shown: 1. On vehicles equipped with the pr emium version, select and press any numbered button without an illumi- nated light above it. 2. Gently insert the disc with the label facing up while the light below the loading slot is illuminated.
• If you insert a disc with the ignition ON and the radio OFF , the DVD will automatically be pulled into the DVD changer and the display will show the time of day . • It is recommended to label home made burned discs with a permanent marker instead of adhesive labels.
Operating Instructions — Remote Control NOTE: Aim the remote control at the DVD changer located on the center of the instrument panel and press the desired button. Direct sunlight or objects blocking the line of sight may affect the function of the remote control.
1. Headphone T ransmitter 2. Menu Up/Next T rack/Chapter 3. Menu Left/Fast Rewind 4. Return 5. Setup 6. Pause/Play 7. Mute 8. Display 9. Mode 10. Program Down - Previous Disc 1 1. Program Up - Next Disc 12. Slow 13. Stop 14. Menu 15. Menu Down/Previous T rack/Chapter 16.
SETUP Button (5) This button only functions in DVD video mode. Press the button after pressing the STOP button to access the DVD changer set up menu. Use the right and left arrows to move between tabs for language, rating, mark, audio and aspect. Use the up and down arrows to move between options within each tab.
STOP Button (13) This button only functions in DVD video mode. Press this button to stop the DVD. MENU Button (14) This button only functions in DVD video mode. Press this button to select the DVD disc menu. NEXT/PREV Buttons (2, 15) Press the up arrow or the NEXT button for the next chapter or track on the disc.
Operating Instructions — Video Screen Push up on the release button to lower the video screen. 1. Screen W idth Button Changes the width of the screen picture.
3. Brightness Button Changes the brightness of the screen picture. Operating Instructions — Headphones 1. Power Button 2. V olume Control 3. Power Indicator UNDERST ANDING YOUR INSTRUMENT P ANEL 183.
Power Button Pressing the power button will turn the headphones ON/OFF . An indicator light will illuminate on the head- phone earpiece to indicate the headphones are ON.
General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation.
NOTE: MP3 player’s, video game systems, camcorders connected to the RCA jacks and CD’s or DVD’s inserted into the CD/DVD changer can be heard through the headphones. SA TELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to receiver broadcast- ing technology to provide clear digital sound, coast to coast.
ESN/SID mode when any other button is pushed, the ignition is turned OFF , or 5 minutes has passed since any button was pushed. ESN/SID Access W ith RBP , RBU, RAZ, and RBQ Radios W ith the ignition switch in the ACCESSORY position and the radio OFF , press the CD Eject and TIME buttons simultaneously for 3 seconds.
Selecting a Channel Press and release the SEEK or TUNE buttons to search for the next channel. Press the top of the button to search up and the bottom of the button to search down. Holding the TUNE button causes the radio to bypass channels until the button is released.
NOTE: Pr essing the ⬙ SEEK ⬙ or ⬙ SCAN ⬙ button while performing a music type scan will change the channel by one and stop the search. Pressing a pre-set memory button during a music type scan, will call up the memory channel and stop the search.
REMOTE SOUND SYSTEM CONTROLS The remote sound system controls are located on the rear surface of the steering wheel at the 3 and 9 o’clock positions. The right hand rocker switch has a push button in the center and controls the volume and mode of the sound system.
CD Player Pressing the top of the switch once will go to the next track on the CD. Pressing the bottom of the switch once will go to the beginning of the current track or to the beginning of the previous track if it is within one second after the current track begins to play .
AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such things as lightning, power lines and neon signs. FM Reception Because FM transmission is based on frequency v.
Maintain your cassette tape player . The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played. The result of deposits on the capstan shaft may cause the tape to wrap around and become lodged in the tape transport.
RADIO OPERA TION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
T o replace the navigation map DVD lift the storage bin cover and liner in the rear cargo area, press the eject button and the disc will eject. Gently insert the new disc into the DVD unit with the label facing up. The disc will automatically be pulled into the DVD unit.
regulates the heating and air conditioning system includ- ing blower speed, outlet air temperature, and airflow distribution through the various outlets within the in- strument panel. Using the ⬙ TEMP ⬙ buttons, adjust the temperature you would like the system to maintain.
• The “DELA Y” symbol will flash to indicate that the feature as been disabled. This feature may be enabled using the following proce- dure: • Press and hold the Heated Rear W indow and Auto HI buttons for 5 seconds. • The “DELA Y” symbol will flash to indicate that the feature as been enabled.
The front blower control can be set to any fixed blower speed by pressing the rocker switch up or down. This allows the front occupants to control the volume of air circulated in the vehicle and cancel the auto mode.
Bi-Level Mode Air comes fr om both the instrument panel outlets and floor outlets. A slight amount of air is also directed through the defrost and side window demister outlets. NOTE: In many temperatur e positions, the bi-level mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets.
Mix Mode Air comes fr om the floor , defr ost and side window demist outlets. This mode is not used when operating in either ⬙ AUTO HI ⬙ or ⬙ AUTO LO ⬙ . This mode should be used when airflow to the floor and windshield is desired. Defrost Mode Air comes from the windshield and side window demist outlets.
NOTE: While operating in ⬙ AUTO HI ⬙ or ⬙ AUTO LO ⬙ , the system will not automatically sense the presence fog, mist, or ice on the windshield. The defrost button must be pressed to clear the windshield and side glass. Depress the “A/C” button to turn on and off the air conditioning during manual operation only .
key is turned “ON”. The frequent use of outside air will help keep odors fr om building up within the air conditioner-heater housing. It is recommended that the recir culation mode be used as little as possible, especially in humid climates.
When the A TC display reads ⬙ REAR AUTO ⬙ or when the rear fan is off, the switch located in the center console between the second row seats is not functional. When the A TC display reads ⬙ REAR ⬙ , only the rear seat occupants can control the rear fan speed from the rear switch.
W indow Fogging V ehicle windows tend to fog on the inside in mild rainy or humid weather . T o clear the windows, use the A/C button to reduce the humidity inside the vehicle. Fogging on the inside of the windshield can be quickly removed by pressing the defrost button and increasing the blower speed.
Electric Rear Window Defroster Press this button to turn on the rear window defroster and the heated side mirrors. A light in the button will illuminate to indicate the rear window defroster is ON. The defroster automatically turns off after about 10 minutes of operation.
I n f o r m a t i o n P r o v i d e d b y :.
ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es ..................... 2 1 0 ▫ Normal Starting ...................... 2 1 0 䡵 Engine Block Heater — If Equipped ......... 2 1 2 䡵 Automatic T ransmission .................. 2 1 3 ▫ Brake/T ransmission Interlock System .
▫ T ire Markings ........................ 2 2 4 ▫ T ire Identification Number (TIN) .......... 2 2 8 ▫ T ire Loading And T ire Pressure ........... 2 2 9 䡵 T ires—General Information ................ 2 3 3 ▫ T ire Pressur e ...............
▫ Gasoline/Oxygenate Blends .............. 2 4 9 ▫ MMT In Gasoline ..................... 2 4 9 ▫ Sulfur In Gasoline ..................... 2 5 0 ▫ Materials Added T o Fuel ................ 2 5 0 ▫ Fuel System Cautions .................. 2 5 1 ▫ Carbon Monoxide W arnings .
ST ARTING PROCEDURES CAUTION! Long periods of engine idling, especially at high engine speeds, can cause excessive exhaust tempera- tures which can damage your vehicle.
W ARNING! • Do not attempt to push or tow your vehicle to get it started. V ehicles equipped with an automatic transmission cannot be started this way . Un- burned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
If the engine shows no sign of starting after two 15 second periods of cranking with the accelerator pedal held to the floor , the “NORMAL ST AR TING” procedur e should be repeated. After Starting The idle speed will automatically decrease as the engine warms up.
AUTOMA TIC TRANSMISSION CAUTION! Damage to the transmission may occur if the follow- ing precautions are not observed: • Shift into P ARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed.
Automatic T ransmission Ignition Interlock System This system prevents the key from being removed unless the shift lever is in P ARK. It also prevents shifting out of P ARK unless the key is in the ACCESSORY or ON position.
NOTE: Even if the transmission can be reset, it is recommended that you visit a dealer at your earliest possible convenience. Y our dealer has diagnostic equip- ment to determine if the problem could recur . If the transmission cannot be reset, dealer service is requir ed.
AUTOSTICK Autostick is a driver-interactive transmission that offers manual gear shifting capability to provide you with more control. Autostick allows you to maximize engine brak- ing, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance.
• Y ou can start out in first, second, or third gear . Shifting into fourth gear can occur only after vehicle speed reaches 15 mph (24 km/h). • The transmission will automatically downshift to first gear when coming to a stop. • Starting out in third gear is helpful in snowy or icy conditions.
CAUTION! All wheels must have the same size and type tires. Unequal tire sizes must not be used. Unequal tire size may cause failure of the power transfer unit and/or the viscous coupling. P ARKING BRAKE When the parking brake is applied with the ignition switch on, the brake light in the instrument cluster will turn on.
The parking brake should always be applied when the driver is not in the vehicle. W ARNING! • Leaving children in a vehicle unattended is dan- gerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector lever .
Anti-Lock Brake System The Anti-Lock Brake System provides increased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to prevent wheel lock-up.
The ABS light monitors the Anti-Lock Brake System. The light will come on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or comes on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is requir ed.
• and a slight drop or fall away of the brake pedal at the end of the stop. These are all normal characteristics of ABS. W ARNING! The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment.
CAUTION! Prolong operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and should be avoided when possible.
NOTE: • The T raction Control system will make buzzing or clicking sounds when in operation. • Extended heavy use of T raction Control may cause the system to deactivate and turn on the traction control indicator located in the instrument cluster .
NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tire sizing is based on European design standards.
T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ ....blank.... ⴖ = Passenger car tire based on European design standards L T = Light T ruck tire based on U.
EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry . H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Tire Loading and Tire Pressure T ire Placard Location NOTE: Some vehicles have a “T ire and Loading Infor- mation” placard located on the driver’s side “B” pillar .
4) the cold tire inflation pressures for the front, rear and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.
passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lb. (1400–750 (5 x 150) = 650 lb.) 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4.
232 ST ARTING AND OPERA TING I n f o r m a t i o n P r o v i d e d b y :.
W ARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, af fect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
2. Economy— Improper inflation pressur es can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption.
check tire pressur e. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are underinflated. CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped.
T ire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressur e is very important.
Radial-Ply Tires W ARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly . The instability could cause an accident. Al- ways use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels).
Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare.
W ARNING! The limited use spare tires are for emergency use only . Installation of this limited use spare tire af fects vehicle handling. W ith this tire, do not drive more than 60 mph (100 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited use spare tire and wheel assembly .
T read Wear Indicators T read wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm).
W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle.
Improper alignment will not cause vehicle vibration. V ibration may be a r esult of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear . ALL WHEEL DRIVE (A WD) — IF EQUIPPED CAUTION! All Wheel Drive (A WD) vehicles must have the same size and type tires on all wheel positions.
1,2,3, OR 4 TIRE(S) LOW PRESSURE Low tire pressure levels of 25 psi [1.72 bars] (172 kPa) or less detected in one or more tires. Inspect all tir es for proper inflation pressure, once the proper tire .
CAUTION! The TPM system has been optimized for the original equipment tires and wheels. TPM system pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sen- sor damage may result when using replacement equipment that is not of the same size, type, and/or style.
General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interfer ence r eceived, including interference that may cause undesired op- eration.
CAUTION! T o avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious damage.
Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). TIRE ROT A TION RECOMMENDA TIONS T ires on the front and rear axles of vehicles operate at differ ent loads and perform dif ferent steering, driving, and braking functions.
FUEL REQUIREMENTS Y our vehicle is designed to meet all emis- sions regulations and provide satisfactory fuel economy and performance when us- ing high quality unleaded gasoline having an octane range of 87 to 89 or higher . The manufacturer recommends the use of 89 octane for optimum performance.
Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol, MTBE, and ETBE. Oxygen- ates are required in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your vehicle.
MMT is prohibited in Federal and California reformu- lated gasolines. Sulfur In Gasoline Y our vehicle may have been designed to meet California low emission standards when using cleaner burning California reformulated gasoline with low sulfur . This vehicle may be sold nationwide.
Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law . Using leaded gasoline can impair engine performance, damage the emission control system, and could result in loss of warranty coverage.
• Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed ar ea, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
CAUTION! T o avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. When the fuel nozzle “clicks” or shuts off, the fuel tank is full. NOTE: • T ighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is properly tightened.
VEHICLE LOADING The load carrying capacity of your vehicle is shown in the charts that follow . This information should be used for passenger and luggage loading as indicated. If the seatbacks are folded for carrying cargo, do not exceed the specified GVWR and GA WR.
W ARNING! Because the front wheels drive and steer the vehicle, it is important that you do not exceed the maximum front or rear GA WR. A dangerous driving condition can result if either rating is exceeded. Y ou could lose control of the vehicle and have an accident.
A loaded vehicle is shown in the illustration. Note that neither the GVWR or the GA WR capacities have been exceeded. Example Only Front Axle Rear Axle Empty W eight 2538 lbs (1 151 kg) 2076 lbs (942 .
Perform maintenance services as prescribed in the main- tenance schedules manual. When your vehicle is used for trailer towing, never exceed the gross axle weight rating (GA WR) by the addition of: • The tongue weight of the trailer . • The weight of any other type of cargo or equipment put in or on your vehicle.
• The automatic transmission fluid and filter should be changed if you REGULARL Y tow a trailer for more than 45 minutes of continuous operation. See Schedule “B” in section 8 of this manual for transmission fluid change intervals. NOTE: • Check the automatic transmission fluid level before towing.
A load equalizing hitch is r ecommended for loaded trailer weights above 1,000 lbs (454 kg) and required for weights above 2,000 lbs (907 kg). CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity .
I n f o r m a t i o n P r o v i d e d b y :.
WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flasher .................. 2 6 2 䡵 If Y our Engine Overheats ................. 2 6 3 䡵 Jacking And T ire Changing ................ 2 6 4 ▫ Jack Location ........................ 2 6 5 ▫ Spare T ire Stowage .
HAZARD W ARNING FLASHER The hazard flasher switch is located in the center of the instrument panel above the center air outlets. T o engage the Hazard W arning Flashers, depress the switch on the instrument panel.
IF YOUR ENGINE OVERHEA TS In any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- tion. • On the highways — Slow down. • In city traffic — While stopped, put transmission in neutral, but do not increase engine idle speed.
W ARNING! A hot engine cooling system is dangerous. Y ou or others could be badly burned by steam or boiling coolant. Y ou may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7, Maintenance, of this manual.
Jack Location The jack and jack-handle are stowed in the rear storage bin located in the rear cargo floor . Pull up on the storage bin cover and liner to access the jack and jack tools. Spare Tire Stowage The spare tire is stowed under the rear of the vehicle by means of a cable winch mechanism.
Spare T ire Removal Fit the jack-handle over the drive nut. Rotate the nut to the left until the spare is on the ground with enough slack cable to allow you to pull the tire out fr om under the vehicle. CAUTION! The winch mechanism is designed for use with the jack handle only .
• Passengers should not remain in the vehicle when the vehicle is being jacked. Jacking Instructions 1. Remove the spare wheel, scissors jack and jack-handle from stowage. 2. Carefully pry off the wheel center cap using the tip of the jack handle. 3.
location. Do not raise the vehicle until you are sure the jack is securely engaged. Never jack up the vehicle using any suspension components. 6. Raise the vehicle by turning the jack screw to the right, using the swivel wrench.
W ARNING! A loose tire or jack, thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided. 12. Secure the flat or spare tire as follows: • The center cap of a cast aluminum wheel must be removed prior to flat tire stowage.
JUMP-ST ARTING PROCEDURES IF BA TTER Y IS LOW W ARNING! T ake care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on.
W ARNING! • Do not attempt to push or tow your vehicle to get it started. V ehicles equipped with an automatic trans- mission cannot be started this way . Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery . Make sure you have a good contact on the engine.
2. Slow down if road has standing water or puddles. 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain sufficient distance between your vehicle and the vehicle in front to avoid a collision in a sudden stop.
TOWING A DISABLED VEHICLE With Ignition Key Front Wheel Drive Y our vehicle may be towed under the following condi- tions: The gear selector must be in NEUTRAL, the distance to be traveled must not exceed 100 miles (160 km), the towing speed must not exceed 44 mph (72 km/h), and both front and rear wheels must be on the ground.
All T ransmissions CAUTION! • Do not attempt to tow this vehicle from the front with sling type towing equipment. Damage to the front fascia will result. • Always use wheel lift equipment when towing from the front. The only other approved method of towing is with a flat bed truck.
TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE (Flat towing with all four wheels on the ground) Flat towing of vehicles equipped with an automatic transmission, is only permitted within the limitations described in this section.
MAINT AINING YOUR VEHICLE CONTENTS 䡵 3.5L Engine ........................... 2 8 0 䡵 Onboard Diagnostic System — OBD II ........ 2 8 1 䡵 Emissions Inspection And Maintenance Programs ............................ 2 8 2 䡵 Replacement Parts ...
▫ Steering Shaft Seal .................... 2 9 5 ▫ Steering Linkage ...................... 2 9 5 ▫ Drive Shaft Universal Joints .............. 2 9 5 ▫ Body Lubrication ..................... 2 9 6 ▫ W indshield W iper Blades ................ 2 9 6 ▫ W indshield And Rear W indow W ashers .
▫ Front Park/T urn Signal And Sidemarker Lights ............................. 3 2 2 ▫ Front Fog Light ...................... 3 2 3 ▫ Rear T ail, Stop, T urn Signal, Side Marker And Back-Up Lights ....................... 3 2 4 ▫ License Light .
3.5L ENGINE 280 MAINT AINING YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboar d diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems.
EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system.
ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine.
NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment.
The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings.
Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed. Check the following list to see if any apply to you. • Day or night temperatures are below 32°F (0°C). • Stop and Go driving. • Extensive engine idling.
American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API).
Synthetic Engine Oils Y ou may use synthetic engine oils provided that the recommended oil quality requir ements are met and the recommended maintenance intervals for oil and filter changes are followed.
Also check belt routing to make sure there is no interfer- ence between the belts and other engine components. Spark Plugs Spark plugs must fire properly to assure engine perfor- mance and emission control. New plugs should be in- stalled at the specified mileage.
Catalytic Converter The catalytic converter requires the use of unleaded fuel only . Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic con- verter will not require maintenance.
W ARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system. Do not park or operate your vehicle in areas where your exhaust system can contact any- thing that can burn.
W ARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water .
Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a system performance check.
Refrigerant Recovery And Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar - bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product.
W ARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary , add fluid to restore to the proper indicated level.
Continued operation could result in failure of the univer- sal joint due to water and dirt contamination of the grease. This would require complete replacement of the joint assembly .
Windshield and Rear Window W ashers The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the engine compartment and should be checked for fluid level at regular intervals.
damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment.
Coolant Checks Coolant protection checks should be made every 12 months (prior to the onset of freezing weather , where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc.
CAUTION! • Mixing of coolants other than the specified HOA T coolant may result in decreased corrosion protec- tion and engine damage that may not be covered under the new vehicle warranty . If a non-HOA T coolant is introduced into the cooling system in an emergency , it should be replaced with the speci- fied coolant as soon as possible.
Coolant Pressure Cap The coolant pr essure cap must be fully tightened to prevent loss of coolant, and to insure that coolant will return to the coolant bottle from the overflow tank. The coolant pressur e cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.
community . T o prevent ingestion by animals or children do not store ethylene glycol based engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately . Clean up any ground spills immediately .
• Maintain coolant concentration at 50% ethylene glycol antifreeze (minimum) in water for proper corrosion protection of your engine which contains aluminum components. • Make sure that the radiator and coolant bottle hoses are not kinked or obstructed.
Brakes In order to assure brake system performance, all brake system components should be inspected periodically . Suggested service intervals can be found in the Mainte- nance Schedules. W ARNING! Riding the brakes can lead to brake failure and possibly an accident.
NOTE: Inspection of brake hoses should be performed whenever the brake system is serviced and at every engine oil change. Inspect hydraulic brake hoses for surface cracking, scuffing, or worn spots.
Use only manufacturers recommended brake fluid, refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. W ARNING! • Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire.
Care should be taken in installing quick connect fittings to insure they are properly installed and fully connected. See your authorized dealer for service. Automatic T ransmission The automatic transmission and differential assembly are contained within a single housing.
Procedure For Checking Fluid Level The fluid level in the automatic transmission should be checked whenever the vehicle is serviced. Operation with an improper fluid level will greatly reduce the life of the transmission and of the fluid. T o properly check the automatic transmission fluid level, the following procedur e must be used: 1.
b. If the fluid is cold, the fluid level should be between the lower two holes in the area marked “COLD”. If the fluid level indicates low , add sufficient fluid to bring to the proper level. CAUTION! Do not overfill. Dirt and water in the transmission can cause serious damage.
All Wheel Drive (A WD) — If Equipped Under normal operating conditions, periodic fluid level checks and lubricant changes for the Power T ransfer Unit, Overrunning Clutch and Rear Carrier , are not requir ed.
Fluid Changes The fluid should be changed as follows: Normal Usage No Service Required Severe Usage Power T ransfer Unit 15,000 miles (24 000 km) Overrunning Clutch 22,500 miles (36 000 km) Rear Carrier 22,500 miles (36 000 km) Severe Usage is defined as: 1.
The following maintenance recommendations will enable you to obtain maximum benefit fr om the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.
CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder , which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.
• If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use Mopar touch up paint on scratches as soon as possible. Y our dealer has touch up paint to match the color of your vehicle. Interior Care Use Mopar Fabric Cleaner to clean fabric upholstery and carpeting.
Glass Surfaces All glass surfaces should be cleaned on a regular basis with any commer cial household-type glass cleaner . Never use an abrasive type cleaner . Use caution when cleaning the inside rear window equipped with electric defrosters or the right rear quarter window equipped with the radio antenna.
Cleaning The Center Console Cup Holders Removal Grab the center of the rubber portion of the cupholder and lift upward. Cleaning Soak the rubber cupholder liner in a mixture of medium hot tap water and one teaspoon of mild liquid dish soap. Let soak for approximately one hour .
Cavity Maxi Fuse Description 1 40 Amp Green Anti-Lock Brake System (ABS) Pump 2 Spare 3 30 Amp Pink Ignition Off Draw (IOD) 4 40 Amp Green Body Control Module (BCM) Feed 1 5 40 Amp Green Electronic Ba.
Cavity Mini Fuse Description 24 20 Amp Y ellow Power Outlet (Selectable) 25 15 Amp Blue Radio, Amplifier , Navi- gation, Hands-Free Phone (HFM), Electronic V ehicle Information Cen- ter (EVIC), EC, SN.
CAUTION! • When installing the Integrated Power Module cover , it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure.
REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Bulb Number Center & Rear Reading Lights ............... 5 7 8 Front Door Courtesy Light .................. 5 7 8 Liftgate Light(s) .......................... 5 7 8 Overhead Console Reading Lights .
BULB REPLACEMENT Standard Quad Headlights 1. Remove the two screws securing the headlight mod- ule to the vehicle and pull the headlight module forward away from the vehicle, disengaging the assembly from the lower attachment clip. 2. Remove the rubber boot seals.
High Intensity Discharge Headlights (HID) — If Equipped The headlights are a type of high voltage discharge tube. High voltage can remain in the circuit even with the headlight switch of f and the key removed. Because of this, you should not attempt to service a headlight bulb yourself.
2. T wist the bulb socket to remove from the headlight module and pull the bulb from socket. 3. Replace the bulb, reinstall the socket and then reinstall the headlight module. Front Fog Light 1. Remove the screw from the front of the fog light and pull out from the front of the fascia.
Rear T ail, Stop, T urn Signal, Side Marker and Back-up Lights 1. Raise the liftgate. 2. Remove the two tail light assembly screws and rotate the assembly outward to remove the ball stud form the attaching grommet. 3. T wist the socket assembly to remove it from the housing.
FLUIDS AND CAP ACITIES U.S. Metric Fuel (approximate) 89 Octane 23 gallons 87 liters Engine Oil-W ith Filter 3.5 Liter Engines (SAE 10W -30, API Certified) 5.5 qts 5.2 liters Cooling System * 3.5 Liter Engines (Mopar 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula) 10.
RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Organic Additive T echnology) Engine Oil Use API Certified.
Chassis Component Fluids, Lubricants and Genuine Parts Automatic T ransmission Mopar 威 A TF+4 Automatic T ransmission Fluid. A WD Power T ransfer Unit Mopar 威 Gear Lubricant 75W -90. A WD Overrunning Clutch Mopar 威 A TF+4 Automatic T ransmission Fluid.
I n f o r m a t i o n P r o v i d e d b y :.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance ........ 3 3 0 䡵 Maintenance Schedules ................... 3 3 0 ▫ Schedule “B” .
EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system.
• T axi, police, or delivery service (commercial ser- vice). 〫 • Off-r oad or desert operation. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙ Maintenance Schedules ⬙ section of this manual.
Once a Month • Check tire pressure and look for unusual wear or damage. • Inspect the battery and clean and tighten the terminals as requir ed. • Check the fluid levels of coolant bottle, brake master cylinder and transmission, add as needed. • Check all lights and all other electrical items for correct operation.
SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an 〫 .
Miles 3, 000 6, 000 9, 000 12, 000 15, 000 18, 000 (Kilometers) (5 000 ) (10 000 ) (14 000) (19 000) (24 000) (29 000) Change engine oil and engine oil filter . XXXXX X Rotate T ires X X X Inspect the brake linings. X X Inspect the engine air cleaner filter , replace if necessary .
Miles 21, 000 24, 000 27, 000 30, 000 33, 000 36, 000 (Kilometers) (34 000) (38 000) (43 000) (48 000) (53 000) (58 000) Change engine oil and engine oil filter . XXXXX X Rotate T ires X X X Inspect the brake linings. X X Inspect the engine air cleaner filter , replace if necessary .
Miles 39, 000 42, 000 45, 000 48, 000 51, 000 54, 000 (Kilometers) (62 000) (67 000) (72 000) (77 000) (82 000) (86 000) Change engine oil and engine oil filter . XXXXX X Rotate T ires X X X Inspect the brake linings. X X Inspect the engine air cleaner filter , replace if necessary .
Miles 57, 000 60, 000 63, 000 66, 000 69, 000 72, 000 (Kilometers) (91 000) (96 000) (101 000) (106 000) (1 10 000) (1 15 000) Change engine oil and engine oil filter . XXXXX X Rotate T ires X X X Inspect the brake linings. X X Inspect the engine air cleaner filter , replace if necessary .
Miles 57, 000 60, 000 63, 000 66, 000 69, 000 72, 000 (Kilometers) (91 000) (96 000) (101 000) (106 000) (1 10 000) (1 15 000) Change the All Wheel Drive (A WD) power transfer unit fluid. (See note at the end of this chart) XX Change the All Wheel Drive (A WD) overrun- ning clutch and rear carrier fluid.
Miles 75, 000 78, 000 81, 000 84, 000 87, 000 90, 000 (Kilometers) (120 000) (125 000) (130 000) (134 000) (139 000) (144 000) Change engine oil and engine oil filter . XXXXX X Rotate T ires X X X Inspect the brake linings. X X Inspect the engine air cleaner filter , replace if necessary .
Miles 75, 000 78, 000 81, 000 84, 000 87, 000 90, 000 (Kilometers) (120 000) (125 000) (130 000) (134 000) (139 000) (144 000) Change the All Wheel Drive (A WD) overrun- ning clutch and rear carrier fluid. (See note at the end of this chart) X Replace the air conditioning filter .
Miles 93, 000 96, 000 99, 000 100, 000 102, 000 105, 000 (Kilometers) (149 000) (154 000) (158 000) (160 000) (163 000) (168 000) Change engine oil and engine oil filter . X X X X X Rotate T ires X X Inspect the brake linings. X Inspect the engine air cleaner filter , replace if necessary .
Miles 93, 000 96, 000 99, 000 100, 000 102, 000 105, 000 (Kilometers) (149 000) (154 000) (158 000) (160 000) (163 000) (168 000) Flush and replace the engine coolant at 60 months or 100,000 miles.
Miles 108, 000 1 11, 000 1 14, 000 117, 000 120, 000 (Kilometers) (173 000) (178 000) (182 000) (187 000) (192 000) Inspect the serpentine drive belt, replace if neces- sary . ‡ X Change the automatic transmission fluid and filter . X Change the All Wheel Drive (A WD) power transfer unit fluid.
SCHEDULE “A” Miles 6, 000 12, 000 18, 000 24, 000 30, 000 36, 000 (Kilometers) (10 000) (19 000) (29 000) (38 000 ) (48 000) (58 000) [Months] [6] [12] [18] [24] [30] [36] Change engine oil and engine oil filter . X XXXXX Rotate T ires X XXXXX Inspect the brake linings.
Miles 42, 000 48, 000 54, 000 60, 000 66, 000 72, 000 (Kilometers) (67 000) (77 000) (86 000) (96 000) (106 000) (115 000) [Months] [42] [48] [54] [60] [66] [72] Change engine oil and engine oil filter . X X XXXX Rotate T ires X X XXXX Inspect the brake linings.
Miles 78, 000 84, 000 90, 000 96, 000 100, 000 (Kilometers) (125 000) (134 000) (144 000) (154 000) (160 000) [Months] [78] [84] [90] [96] Change engine oil and engine oil filter . X X X X Rotate T ires X X X X Inspect the brake linings. X Inspect the engine air cleaner filter , replace if necessary .
Miles 102, 000 108, 000 1 14, 000 120, 000 (Kilometers) (163 000) (173 000) (182 000) (192 000) [Months] [102] [108] [114] [120] Change engine oil and engine oil filter . X X X X Rotate T ires X X X X Inspect the brake linings. X Inspect the engine air cleaner filter , replace if necessary .
* This maintenance is recommended by the manufacture to the owner but is not requir ed to maintain the emis- sions warranty . ‡ This maintenance is not required if previously replaced. Inspection and service should also be performed anytime a malfunction is observed or suspected.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle .............................. 3 5 0 ▫ Prepar e For The Appointment ............ 3 5 0 ▫ Prepar e A List ........................ 3 5 0 ▫ Be Reasonable W ith Requests .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional char ges with the service manager .
The manufacturer has empowered its dealers to make warranty and repair decisions that ensur e you ar e not inconvenienced. There is no need for you to wait for a decision from the manufacturer .
Mexico, D. F . In Mexico (915) 729–1248 or 729–1240 Outside Mexico (525) 729–1248 or 729–1240 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its Customer Center .
W e appreciate that you have made a major investment when you purchased your new vehicle. Y our dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with your ownership experience. Y ou’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns.
354 IF YOU NEED CONSUMER ASSIST ANCE I n f o r m a t i o n P r o v i d e d b y :.
MOP AR 姞 P ARTS Mopar 威 fluids, lubricants, parts, and accessories are available from your dealer . They will help you keep your vehicle operating at its best.
PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Mas- tercar d, American Express, and Discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form.
Call T oll Free at 1–800–890–4038 (U.S.) or 1–800–387–1143 (Canada) Or V isit us on the W orld W ide W eb at: www .techauthority .daimlerchrysler .
W ARNING! The traction grade is based on braking (straight- ahead) traction tests and does not include cornering (turning) performance. T emperature Grades The temperature grades are A (highest), B, a.
INDEX 10 I n f o r m a t i o n P r o v i d e d b y :.
Adding Fuel ........................... 2 5 2 Adding W asher Fluid .................. 1 15,297 Additives, Fuel ......................... 2 5 0 Adjustable Pedals ........................ 1 1 8 Air Conditioner Maintenance ............... 2 9 3 Air Conditioning Filter .
Selection Of Lubricant ................ 307,327 Shifting ............................. 2 1 5 Special Additives ...................... 3 0 9 Autostick ........................ 120,215,216 Ball Joints ............................. 2 9 5 Battery ........
Catalytic Converter ...................... 2 9 0 Caution, Exhaust Gas ................... 60,297 CD Changer ...................... 165,173,175 CD Player .................. 161,163,165,172,175 CD Player Maintenance ................... 1 9 3 Cellular Phone .
Cruise Control .......................... 1 1 9 Cruise Light ........................... 1 4 9 Cup Holder ......................... 133,316 Customer Assistance ..................... 3 5 0 Dealer Service .......................... 2 8 3 Defroster , Rear W indow .
Block Heater ......................... 2 1 2 Break-In Recommendations ................ 5 9 Checking Oil Level ..................... 2 8 4 Compartment ......................... 2 8 0 Coolant ............................. 3 2 6 Cooling .................
Fog Light Service ........................ 3 2 3 Fog Lights ....................... 1 12,150,323 Folding Rear Seat ........................ 1 0 1 Freeing A Stuck V ehicle ................... 2 7 3 Fuel ................................. 2 4 8 Adding ..
Head Phones ........................... 1 8 3 Head Restraints .......................... 9 4 Headlights ............................ 3 2 2 Bulb Replacement ...................... 3 2 1 High Beam ........................... 1 1 3 High Beam/Low Beam Select Switch .
Key , Programming ........................ 1 4 Key , Replacement ........................ 1 4 Key , Sentry ............................. 1 2 Key-In Reminder ......................... 1 2 Keyless Entry System ...................... 1 9 Keys ...........
Oil Pressur e .......................... 1 5 0 Park ............................... 3 2 2 Reading ............................. 1 2 2 Rear Servicing ........................ 3 2 4 Rear T ail ............................ 3 2 4 Seat Belt Reminder ......
Mini-T rip Computer ...................... 1 5 9 Mirrors ................................ 6 7 Automatic Dimming ..................... 6 7 Electric Remote ........................ 6 9 Exterior Folding ........................ 6 8 Heated ...............
Overhead T ravel Information Center .......... 1 2 2 Overheating, Engine ................... 144,263 Owner’s Manual ....................... 4,356 Panic Alarm ............................ 2 1 Parking Brake .......................... 2 1 8 Parking On Hill .
Radio, Satellite .......................... 1 8 6 Rear Liftgate ............................ 2 6 Rear Seating Flexibility .................... 1 0 1 Rear W indow Defroster ................... 2 0 5 Rear W indow Features .................... 1 1 4 Rear W iper/W asher .
Adjustable Upper Shoulder Anchorage ........ 3 6 And Pregnant W omen ................... 4 1 Child Restraint ......................... 5 1 Extender ............................. 4 1 Front Seat ............................ 3 1 Pretensioners ...........
Starting and Operating .................... 2 1 0 Starting Procedur es ...................... 2 1 0 Steering Linkage ............................. 2 9 5 Power ........................... 222,294 Shaft Seal ............................ 2 9 5 T ilt Column .
Changing ............................ 2 6 4 Compact Spare ........................ 2 3 7 General Information .................... 2 3 3 High Speed .......................... 2 3 6 Inflation Pressur es ..................... 2 3 4 Jacking ..............
T ransporting Pets ........................ 5 9 T read W ear Indicators .................... 2 4 0 T rip Odometer .......................... 1 4 8 T rip Odometer Reset Button ................ 1 4 8 T urn Signals ................... 1 12,145,322,324 Uniform T ire Quality Grades .
W indshield W ipers ....................... 1 1 3 W iper Blade Replacement .................. 2 9 6 W iper , Rear ............................ 1 1 4 W ipers, Intermittent .
Een belangrijk punt na aankoop van elk apparaat Chrysler Pacifica Touring (2005) (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Chrysler Pacifica Touring (2005) heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Chrysler Pacifica Touring (2005) vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Chrysler Pacifica Touring (2005) leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Chrysler Pacifica Touring (2005) krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Chrysler Pacifica Touring (2005) bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Chrysler Pacifica Touring (2005) kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Chrysler Pacifica Touring (2005) . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
