Gebruiksaanwijzing /service van het product Network Device 7010 van de fabrikant Cisco
Ga naar pagina of 22
1 Doc. No . Copyright © 1995 Cisco Systems, Inc. All rights reser ved. Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions 78-1230-02 Cisco 7010 Product Number s: CHAS-7010-DC=, CHAS-7010-A C.
2 Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions Product Overview Pr oduct Overview The Cisco 7010 is the five-slot model in the Cisco 7000 series. The Cisco 7010 provides three interface processor slots. Figure 1 shows the interf ace processor end of the Cisco 7010.
Cisco 7010 and Cisco 7505 Chassis Replacement Instructions 3 Product Overview The remov able chassis cov er panel at the noninterface processor end of the router pro vides access to the internal components.
4 Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions Prerequisites Prerequisites Before you begin this installation, re vie w the safety guidelines in this section to av oid injuring yourself or damaging the equipment. This section also provides a list of the tools that you need to perform this replacement.
Cisco 7010 and Cisco 7505 Chassis Replacement Instructions 5 Prerequisites Lifting Saf ely A fully configured chassis weighs approximately 70 pounds. Before installing the new (replacement) chassis, .
6 Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions Prerequisites Cable Str ain Relief If possible, position the new replacement chassis close enough to the e xisting system so that you can av oid ha ving to disconnect power and interf ace cables.
Cisco 7010 and Cisco 7505 Chassis Replacement Instructions 7 Prerequisites Note If these conditions are not true, for instance, if you must remov e a rack-mounted chassis before you can install the new chassis, you must disconnect all po wer and netw ork interface cables.
8 Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions Replacing the Chassis T ools and P ar ts Required This section lists the tools and parts you will need to complete these replacement procedures.
Cisco 7010 and Cisco 7505 Chassis Replacement Instructions 9 Replacing the Chassis Replacing a Rack-Mounted Chassis This section describes how to replace a chassis that is installed in an equipment rack.
10 Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions Replacing the Chassis Removing the Existing Chassis from the Rac k Before removing the e xisting chassis from the rack, you must shut down the system po wer and disconnect the power cord and all interf ace cables.
Cisco 7010 and Cisco 7505 Chassis Replacement Instructions 11 Replacing the Chassis Step 5 Repeat Steps 2 through 4 for the left ear . The strip of mounting holes on the front of each ear should be approximately flush with the end of the chassis. (See Figure 5.
12 Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions Replacing the Chassis Figure 6 Installing the Chassis in a Standard Four -P ost, 19-Inch Equipment Rac k Installing the Cable Management .
Cisco 7010 and Cisco 7505 Chassis Replacement Instructions 13 Replacing the Chassis Figure 7 Cable Management Brac kets—Cisco 7010 Shown Follo w these steps to install the two cable management brack ets on the new chassis: Step 1 If you hav e ne w brackets to install on the ne w chassis, proceed to Step 4.
14 Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions Replacing the Chassis Moving Processor Modules At the interface processor end of the chassis, slots contain the processor modules.
Cisco 7010 and Cisco 7505 Chassis Replacement Instructions 15 Replacing the Chassis Figure 8 Ejector Lever s and Captive Installation Screws Interface processor card slot Interface processor card carr.
16 Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions Replacing the Chassis Follo w these steps to mov e the processor modules to the ne w chassis: Step 1 Before moving an y processor modules.
Cisco 7010 and Cisco 7505 Chassis Replacement Instructions 17 Replacing the Chassis Step 9 Using the thumb and forefinger of each hand to pinch each ejector , simultaneously push both ejectors inward (to ward the carrier handle) until the y snap into place and are at a full 90-degree orientation to the faceplate.
18 Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions Replacing the Chassis Checking the Installation T o complete the replacement procedure, perform the follo wing steps to verify that the system is functioning properly . These steps will also help you verify that all the processor modules you mov ed are returned to their previous state.
Cisco 7010 and Cisco 7505 Chassis Replacement Instructions 19 Replacing the Chassis Step 6 When the system boot is complete, the RP or RSP1 begins to initialize the interface processors. During this initialization, the LEDs on each interface processor beha ve dif ferently (most flash on and off).
20 Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions Replacing the Chassis show Command Descriptions and Examples This section describes the various show commands that you can use to display system status and configuration.
Cisco 7010 and Cisco 7505 Chassis Replacement Instructions 21 Replacing the Chassis The command show interfaces serial slot/port displays statistics for the specific serial interface you specify by its slot/port address.
22 Cisco 7010 and Cisco 7505 Chassis Replacement Instr uctions Cisco Information Online Cisco Inf ormation Online Cisco Information Online (CIO) is Cisco Systems’ primary , real-time support channel. Maintenance customers and partners can self-register on CIO to obtain additional content and services.
Een belangrijk punt na aankoop van elk apparaat Cisco Network Device Cisco 7010 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Cisco Network Device Cisco 7010 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Cisco Network Device Cisco 7010 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Cisco Network Device Cisco 7010 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Cisco Network Device Cisco 7010 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Cisco Network Device Cisco 7010 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Cisco Network Device Cisco 7010 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Cisco Network Device Cisco 7010 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
