Gebruiksaanwijzing /service van het product UNGO MS3001 van de fabrikant Clarion
Ga naar pagina of 26
install_MS3001.qxd 8/11/99 4:15 PM Page 1.
1. Before Y ou Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 1 2. Installation Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MS3001 / MS3200 Installation Manual - Page 1 1. Be sure to read the manual thoroughly before beginning the installation to ensure a proper understanding of the MS3001 / MS3200 and its functions.
Page 2 - MS3001 / MS3200 Installation Manual 1. Use a V olt / Ohm meter to test all wires. Do not use a test light. 2. Good power and ground connections are essential for proper operation. 3. Route all wires from the engine compartment to the interior of the vehicle through a grommet and use electrical tape and split loom tubing for protection.
MS3001 / MS3200 Installation Manual - Page 3 Main Unit The main unit should be mounted in the interior of the vehicle. Do not mount the main unit in the engine compartment. For maximum security , avoid mounting the main unit where it will be easily accessible to a thief.
Page 4 - MS3001 / MS3200 Installation Manual For maximum security , it is best to disguise all under hood system wires with factory style split loom tubing so that they cannot be easily identified by a thief. Run all wires from the engine compartment into the interior of the vehicle through a grommet.
MS3001 / MS3200 Installation Manual - Page 5 +12v +12v Chassis Ground +12v LED Override Switch Black Red White Y ellow White/brown Orange +12v (MS3200 only) Y ellow/white Red/yellow P arking Lights Re.
Page 6 - MS3001 / MS3200 Installation Manual 14-Pin Main Harness Pin 1 - BLACK: Ground. Connect to a solid chassis ground. Be sure to use a ring connector of proper size. Scrape away the paint at the grounding point. Pin 2 - RED: Main Power (+12v) input [3A fuse].
MS3001 / MS3200 Installation Manual - Page 7 In this configuration, the vehicle ’ s starter will be disabled only when the system is armed and alarming. If power to the system is lost or the system becomes disconnected, the vehicle will be able to start.
Page 8 - MS3001 / MS3200 Installation Manual 4-Pin Auxiliary Function Harness Pin 1 - YELLOW/black: Auxiliary Function 2 (-) output. Provides a negative output to activate a relay . The output of this wire can be set to operate in one of two operating modes.
MS3001 / MS3200 Installation Manual - Page 9 Jumper Selections Parking Light Polarity . Selects the polarity (+/-) for the output of the on-board Parking Light relay .
Page 10 - MS3001 / MS3200 Installation Manual Accessing the Jumpers Using a flathead screwdriver , carefully press in on the access tabs on the sides of the case until the hooks release.
MS3001 / MS3200 Installation Manual - Page 11 Remote T ransmitter Layout Each system comes with 2 Remote T ransmitters, pre-programmed to Arm and Disarm the system with chirp confirmation using Button 1 . Button 1 Arms and Disarms the system. This Button also locks and unlocks the doors when the system is in V alet Mode.
Page 12 - MS3001 / MS3200 Installation Manual T wo Car Operation For your convenience, you may use a single transmitter to operate multiple vehicles. The T ransmitter can be set to arm Car #1 with Button 1 and arm additional cars with the first available Buttons not being used by Car #1.
MS3001 / MS3200 Installation Manual - Page 13 Adding a New T ransmitter into the System 1. T urn on the ignition. 2. Press and hold the Override switch. • The status LED will turn on red. 3. Within 5 seconds: Continue holding the Override switch and Press T ransmitter Button 1* For remote arming with chirp confirmation.
Page 14 - MS3001 / MS3200 Installation Manual Arming Mode Selection (Passive or Active Arming) Using the Remote T ransmitter, you may select Passive Arming with chirp confirmation, Passive Arming without chirp confirmation, or Active Arming (Remote only).
MS3001 / MS3200 Installation Manual - Page 15 V alet Mode Allows you to temporarily disable the security system when the car is being serviced or turned over to a parking attendant. T o turn V alet Mode on or off: 1. T urn on the ignition. 2. Press and hold the override switch.
Page 16 - MS3001 / MS3200 Installation Manual The MS3001 / MS3200 ’ s dual stage, on-board Shock Sensor is adjusted entirely through the use of the Remote T ransmitter. T rigger Sensitivity The T rigger sensitivity is adjustable to 8 levels, including an “ off ” setting where the sensor is ignored.
MS3001 / MS3200 Installation Manual - Page 17 Y ou can use this chart to quickly identify and interpret the MS3001 / MS3200 system ’ s chirp indications and LED flashes. The system continuously monitors all protected zones, even when it is not armed, and warns you if it detects a problem when you turn off the ignition.
Page 18 - MS3001 / MS3200 Installation Manual Dome Light Control Relay Diagrams The Auxiliary Function 2 Output can be set for momentarty or latched operation allowing custom operation of vehicle syst.
MS3001 / MS3200 Installation Manual - Page 19 Door Lock Diagrams Negative T rigger Positive T rigger V oltage Reversal Aftermarket Actuators V acuum Lock System White/green = (-) Lock White/blue = (-) Unlock install_MS3001.
Page 20 - MS3001 / MS3200 Installation Manual The optional DLRM is a factory door lock integration module with built-in relays for use with high current positive trigger door locking systems (like tho.
MS3001 / MS3200 Installation Manual - Page 21 Be sure to add a fuse to the violet wire of the 5-pin harness and connect to a constant source of power separate from the alarm ’ s power wire. DO NOT connect the DLRM V iolet wire to alarm ’ s main power lead .
Page 22 - MS3001 / MS3200 Installation Manual Notes install_MS3001.qxd 8/11/99 4:15 PM Page 22.
MS3001 / MS3200 Installation Manual - Page 23 Notes install_MS3001.qxd 8/11/99 4:15 PM Page 23.
+12v +12v Chassis Ground +12v LED Override Switch Black Red White Y ellow White/brown Orange +12v (MS3200 only) Y ellow/white Red/yellow P arking Lights Relay Dome Light Relay Horn Relay 10A Negative .
Een belangrijk punt na aankoop van elk apparaat Clarion UNGO MS3001 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Clarion UNGO MS3001 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Clarion UNGO MS3001 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Clarion UNGO MS3001 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Clarion UNGO MS3001 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Clarion UNGO MS3001 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Clarion UNGO MS3001 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Clarion UNGO MS3001 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
