Gebruiksaanwijzing /service van het product L26 van de fabrikant Clarke
Ga naar pagina of 32
Form No. 70643A 7/04 CLARKE TECHNOLOGY Printed in the U.S.A . READ THIS BOOK CAUTION: Read the Operator's Manual before using the appliance. This book has important information for the use and safe operation of this machine.
Page -2- CLARKE TECHNOLOGY Operator's Manual -Encore L26 Cylindrical Table of Contents SECTION II - Parts and Service Manual How to Correct Problems in the Machine ..................................................................................
CLARKE TECHNOLOGY Operator's Manual - Encore L26 Cylindrical Page -3- OPERA T OR SAFETY INSTRUCTIONS WARNING AVERTISSEMENT ADVERTENCIA D A N G E R : Failure to read and observe all DANGER statements could result in severe bodily injury or death. Read and observe all DANGER statements found in your Owner's Manual and on your machine.
Page -4- CLARKE TECHNOLOGY Operator's Manual -Encore L26 Cylindrical WARNING: Maintenance and repairs performed by unauthorized personnel could result in damage or injury. Maintenance and repairs must be performed by authorized Clarke Technology personnel only.
CLARKE TECHNOLOGY Operator's Manual - Encore L26 Cylindrical Page -5- SPECIFICATIONS: Model Encore L26 Cylindrical Machine Power Supply 24 Volt D.C., (4) 6V 250 AH Deep Cycle Batteries or (4) 6V 330 AH Deep Cycle Batteries Pad or Brush 26" Cylindrical 2 per machine Traverse 0.
Page -6- CLARKE TECHNOLOGY Operator's Manual -Encore L26 Cylindrical Procedures For Transporting How to Put the Machine Into a Van or Truck WARNING: This machine is heavy. Get assistance before attempting to transport or move it. Use two able persons to move the machine on a ramp or incline.
CLARKE TECHNOLOGY Operator's Manual - Encore L26 Cylindrical Page -7- 11. Fasten the machine to the vehicle. Clarke Technology recommends a strap over the top of the machine and a strap to keep the machine from rolling forward or backwards. If this is not done, there is a possibility of the machine toppling over.
Page -8- CLARKE TECHNOLOGY Operator's Manual -Encore L26 Cylindrical SYMBOLS USED ON ENCORE L26 CYLINDRICAL Solution Control Brush Up/Down Warning Power Traverse Speed Control Traverse Directions.
CLARKE TECHNOLOGY Operator's Manual - Encore L26 Cylindrical Page -9- SYMBOLS USED ON ENCORE L26 CYLINDRICAL Warning Label with parking brake Warning Label without parking brake.
Page -10- CLARKE TECHNOLOGY Operator's Manual -Encore L26 Cylindrical Machine Control Panel Figure 3 Circuit Breakers (See Fig 3, Items "F", "G", "H", "I" & "J") The circuit breaker reset buttons are located on the rear cover.
CLARKE TECHNOLOGY Operator's Manual - Encore L26 Cylindrical Page -11- Machine Controls and Features Squeegee Lift Handle, See Figures 4 and 5 The squeegee lift handle is located below the control handles in the center. It is used to raise or lower the squeegee.
Page -12- CLARKE TECHNOLOGY Operator's Manual -Encore L26 Cylindrical Figure 8B How To Install The Batteries The Encore machines uses either two 12-volt batteries or four - 6 volt batteries. The batteries are located in the battery compartment under the recovery tank.
CLARKE TECHNOLOGY Operator's Manual - Encore L26 Cylindrical Page -13- Battery Maintenance The electrical power to operate the machine comes from the storage batteries. Storage batteries need preventative maintenance. WARNING: Working with batteries can be dangerous.
Page -14- CLARKE TECHNOLOGY Operator's Manual -Encore L26 Cylindrical How To Prepare the Machine For Operation Figure 12 Figure 13 How To Charge The Batteries WARNING: Charging the batteries in an area without adequate ventilation could result in an explosion.
CLARKE TECHNOLOGY Operator's Manual - Encore L26 Cylindrical Page -15- 4. Disconnect the battery pack connector from the control housing connector. See figure 14A. 5. Connect the DC connector on the charger to the battery pack connector. See figure 14B.
Page -16- CLARKE TECHNOLOGY Operator's Manual -Encore L26 Cylindrical DANGER: Operating a machine that is not completely or fully assembled could result in injury or property damage. Do not operate this machine unless it is completely assembled. Inspect the machine carefully before operation.
CLARKE TECHNOLOGY Operator's Manual - Encore L26 Cylindrical Page -17- Figure 21 Operating The Machine NOTE: Put the machine in the lowest traverse speed setting. Use the machine in an area that has no furniture or objects until you can do the following: 1.
Page -18- CLARKE TECHNOLOGY Operator's Manual -Encore L26 Cylindrical WARNING: This machine is capable of maximum head pressure with worn brushes. With this feature, there is the possibility of exceeding the recommended brush pressure on new brushes.
CLARKE TECHNOLOGY Operator's Manual - Encore L26 Cylindrical Page -19- WARNING: Maintenance and repairs must be done by authorized personnel only. WARNING: Always empty the solution tank and recovery tank before doing any maintenance. WARNING: Keep all fasteners tight.
Page -20- CLARKE TECHNOLOGY Operator's Manual -Encore L26 Cylindrical Do These Procedures When You End Your Work 1. Drain the solution tank (Figure 25) and the recovery tank (Figure 26). To drain the tanks , follow this procedure: a. Turn the key switch “OFF”.
CLARKE TECHNOLOGY Operator's Manual - Encore L26 Cylindrical Page -21- 8 . Check the batteries and if necessary add distlled water after charging. The correct level is within 1/4 inch (1/2 cm) of the bottom of the tube in each cell. CAUTION : Tap water may contain contami- nants that will damage batteries.
Page -22- CLARKE TECHNOLOGY Operator's Manual -Encore L26 Cylindrical WARNING: Do not operate or perform maintenance on the machine while the recovery tank is in the intermediate position. The tank can be accidentally bumped and it may slam shut.
CLARKE TECHNOLOGY Operator's Manual - Encore L26 Cylindrical Page -23- Maintenance cont. How To Adjust The Squeegee The following adjustments are set at the factory, however they may require slight adjustment.
Page -24- CLARKE TECHNOLOGY Operator's Manual -Encore L26 Cylindrical 6. Locate the four mounting studs on the brush head bracket. See figure 37. The top two mounting nuts can be accessed through the top of the solution tank. The lower two can be accessed through the front.
CLARKE TECHNOLOGY Operator's Manual - Encore L26 Cylindrical Page -25- Clarke Technology Encore L26 Cylindrical Accessories - 3/02 A CCESSORIES Description Part No.
Page -26- CLARKE TECHNOLOGY Operator's Manual -Encore L26 Cylindrical NOTE S.
CLARKE TECHNOLOGY Operator's Manual - Encore L26 Cylindrical Page -27- ENCORE L26 Cylindrical Section II Part s and Service Manual (70643A).
Page -28- CLARKE TECHNOLOGY Operator's Manual -Encore L26 Cylindrical There is no solution flow . The solution flow does not stop. The machine does not remove all the water from the floor. The batteries do not give the normal running time. Fill the solution tank.
CLARKE TECHNOLOGY Operator's Manual - Encore L26 Cylindrical Page -29- PROBLEM CAUSE ACTION The cleaning is not even. The scrub brush or pad is worn. There is damage to the brush assembly, caster or the solution valve. The brush motor is not running The solution level is low.
NOTE S.
AL T O ® PRODUCT SUPPOR T BRANCHES PRODUCTION F ACILITIES AL T O Danmark A/S, Aalborg Blytaekkervej 2 DK-9000 Aalborg +45 72 18 21 00 AL T O Danmark A/S, Hadsund Industrikvarteret DK-9560 Hadsund +45 72 18 21 00 SALES SUBSIDIARIES AL T O Canada Ltd., Rexdale Ontario 24 Constellation Ct.
CLARKE TECHNOLOGY LIMITED U.S. W ARRANTY This Clarke T echnology Industrial/Commercial Product is warranted to be free from defects in materials and workman- ship under normal use and service for a pe.
Een belangrijk punt na aankoop van elk apparaat Clarke L26 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Clarke L26 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Clarke L26 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Clarke L26 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Clarke L26 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Clarke L26 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Clarke L26 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Clarke L26 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
