Gebruiksaanwijzing /service van het product 10500 van de fabrikant 3M
Ga naar pagina of 40
TM AccuGlide ™ is a Trademark of 3M, St. Paul, MN 55144-1000 Litho in U.S.A © 3M 2005 44-0009-2036-1(A) AccuGlide 2+ STD 2 Inch Upper and Lower T aping Heads T ype 10 5 00 Instructions and Parts List Serial No. _____________________________________ For reference, record taping head(s) serial number(s) here.
Replacement Parts and Service Information T o Our Customers: This is the 3M-Matic™/AccuGlide™/Scotch ® equipment you ordered. It has been set up and tested in the factory with Scotch ® t apes. If technical assist ance or replacement p art s are needed, call or fax the appropriate number listed below .
Replacement Parts and Service Information T o Our Customers: This is the 3M-Matic™/AccuGlide™/Scotch ® equipment you ordered. It has been set up and tested in the factory with Scotch ® t apes.
Instruction Manual AccuGlide ™ 2+ STD 2 Inch Upper and Lower Taping Heads Type 10 5 00 Table of Contents Page Equipment Warranty and Limited Remedy .......................................................................................... ..... ii Taping Head Contents .
Equipment Warranty and Limited Remedy: THE FOLLOWING WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FIT.
1 AccuGlide™ 2+ STD 2 Inch Upper Taping Head , Type 10 5 00 Intended Use The intended use of the AccuGlide ™ 2+ STD 2 Inch Upper and Lower Taping Heads is to apply a "C" clip of Scotch ® pressure-sensitive film box sealing tape to the top and/or bottom center seam of regular slotted containers.
2 Import ant Safeguards This safety alert symbol identifies important safety messages in this manual. READ AND UNDERSTAND THEM BEFORE INSTALLING OR OPERATING THIS EQUIPMENT. Explanation of Signal Word Consequences Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury and/or property damage.
3 Import ant Safeguards (Continued) Important – In the event the following safety labels are damaged or destroyed, they must be replaced to ensure operator safety . See "Replacement Parts Illustrations and Parts Lists" for label part numbers.
4 S pecifications 1. Tape: For use with Scotch ® pressure-sensitive film box sealing tapes. 2. Tape Width: 36 mm or 1-1/2 inches minimum to 48 mm [2 inches] maximum. 3. Tape Roll Diameter: Up to 405 mm [16 inches] maximum on a 76.2 mm [3 inch] diameter core.
5 Figure 2-1 – Dimensional Drawing S pecifications (Continued).
6 Inst allation 1. The box conveying system must positively propel the box in a continuous motion, not exceeding 0.40 m/s [80 feet per minute], past the taping head assembly since the box motion actuates the taping mechanism.
7 Operation Figure 3-1 – Taping Head Components/Threading Diagram, Upper Head (Left Side View) Figure 3-2 – Taping Head Components/Threading Diagram – Lower Head (Left Side View).
8 It is recommended that the detailed instructions and sketches in this manual be referred to the first few times the taping head is loaded/threaded until the operator becomes thoroughly familiar with the tape loading operation. Note – Remove tape roll before removing taping head from machine to minimize weight.
9 Operation (Continued) Manually turn tape roll to create slack tape while pulling threading needle through tape applying mechanism until needle is through and tape is in alignment with applying roller. Excess tape can be cut with a scissors at applying roller.
10 The AccuGlide™ STD 2+ 2 Inch Taping Head has been designed for long, trouble free service. The taping head will perform best when it receives routine maintenance and cleaning. Taping head components that fail or wear excessively should be promptly repaired or replaced to prevent damage to other portions of the head or to the product.
11 Maintenance (Continued) Applying/Buffing Roller Replacement Replacing roller requires removal of shaft and mounting screws. With no area on the shaft to grip, the shaft often turns when attempting to remove the second screw.
12 Tape Drum Friction Brake – Figure 5-3 The tape drum friction brake on each taping head is pre-set for normal operation to prevent tape roll over travel. Should tension adjustment be required, turn the self-locking nut on the shaft to vary compression of the spring.
13 Adjustment s (Continued) Applying Mechanism Spring To obtain access to the spring, remove the taping head cover (four mounting screws). Replace cover when finished. The applying mechanism spring, shown in Figures 5-4A and 5-4B, controls applying and buffing roller pressure on the box and returns the mechanism to the reset position.
14 Adjustment s (Continued)| Figure 5-6 – Leading Tape Leg Length Figure 5-7 – Changing Tape Leg Length • To reduce the risk associated with shear, pinch, and entanglement hazards: − Turn air .
15 (Continued) T roubleshooting Cause The tape is threaded incorrectly The tape tension is too low The knurled roller drags Tape tracks to one side or drags on the support tabs of applying frame The o.
16 Problem Tape is tabbing on the trailing leg on the back of the box The tape end does not stay in application position in front of the applying roller Tape not centered on box seam Cause There is ex.
17 S p are Part s/Service Information Recommended Spare Parts A set of spare parts that will periodically require replacement due to normal wear is supplied with the taping heads. The set includes the following which should be reordered when used to keep the taping heads in production: AccuGlide™ 2+ STD 2 Inch Upper Taping Head Qty.
18 Replacement Part s Illustrations and Part s List s AccuGlide™ 2+ STD 2 Inch Upper Taping Head, Type 10 5 00 AccuGlide™ 2+ STD 2 Inch Lower Taping Head, Type 10 5 00 1. Refer to the Taping Head Assemblies Figure to find all the parts illustrations identified by figure numbers.
19 T aping Head Assemblies – AccuGlide ™ 2+ STD 2 Inch.
20 Figure 10397 – Upper Head.
21 Figure 10397 – 2" Upper Head Ref. No. 3M Part No. Description 10397-1 78-8133-9456-2 Frame – Tape Mount Upper Assembly 10397-2 78-8133-9458-8 Frame – Front Upper Assembly 10397-3 78-8068.
22 Figure 10393 – Upper and Lower Heads.
23 Figure 10393 – 2" Upper and Lower Heads Ref. No. 3M Part No. Description 10393-1 78-8133-9509-8 Applying Arm #1 10393-2 78-8133-9510-6 Applying Arm #2 10393-3 78-8070-1221-2 Plate – Tape 1.
24 Figure 10387 – Upper Head.
25 Figure 10387 – 2" Upper Head Ref. No. 3M Part No. Description 10387-1 78-8070-1392-1 Buffing Arm – Sub Assembly 10387-2 78-8070-1391-3 Buffing Arm – Sub Assembly 10387-3 78-8052-6575-4 S.
26 Figure 10395 – Upper and Lower Heads.
27 Ref. No. 3M Part No. Description 10395-1 78-8070-1388-9 Link – Arm Bushing Assembly 10395-2 78-8070-1389-7 Link – Arm Bushing Assembly 10395-3 78-8070-1271-7 Shaft – Pivot 10395-4 78-8017-908.
28 Figure 10391 – Upper and Lower Heads.
29 Figure 10391 – 2" Upper and Lower Heads Ref. No. 3M Part No. Description 10391-1 78-8070-1217-0 Frame – Cut-Off Weldment 10391-2 78-8017-9173-8 Blade – 65 mm/2.
30 Figure 10401 – Upper and Lower Heads 4 14.
31 Figure 10401 – 2" Latch Upper and Lower Heads Ref. No. 3M Part No. Description 10401-1 78-8070-1395-4 Bracket – Bushing Assembly 10401-2 78-8076-4519-3 Shaft – Tape Drum, 50 mm 10401-3 7.
32 Figure 10399 – Lower Head.
33 Figure 10399 – 2" Lower Head Ref. No. 3M Part No. Description 10399-1 78-8133-9502-3 Frame – Tape Mount Lower Assembly 10399-2 78-8133-9500-7 Frame – Front Lower Assembly 10399-3 78-8068.
34 Figure 10389 – Lower Head.
35 Figure 10389 – Lower Head Ref. No. 3M Part No. Description 10389-1 78-8070-1391-3 Buffing Arm Sub Assembly, #1 10389-2 78-8070-1392-1 Buffing Arm Sub Assembly, #2 10389-3 78-8052-6575-4 Shaft –.
Een belangrijk punt na aankoop van elk apparaat 3M 10500 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen 3M 10500 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens 3M 10500 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding 3M 10500 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over 3M 10500 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van 3M 10500 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de 3M 10500 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met 3M 10500 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
