Gebruiksaanwijzing /service van het product 139.53610 van de fabrikant Craftsman
Ga naar pagina of 24
00000 OD 139 1 1 39°53606 1 39.5361 0 - 1/3HP - 1/2 HP = 1/2 HP ° 1/3 HP Owners Manual CAUTION READ INSTRUCTIONS AND RULES FOR SAFE OPERATION CAREFULLY CONTENTS PAGE Features of Your Opener ............. 2 Specifications .......................... 2 Accessories .
FEATURES OF YOUR OPENER 1. Motor: Permanently lubricated with automatic reset, 2. Opener Light: Turns on and off automatically. Provides 4-1/2 minute illumination for your safety and convenience, 3. Safety System: Independent up and down force adjustment.
CARTON CHECK LIST SEARS has packaged yourGarage Door Opener in two cartons which contain all the parts and hardware illustrated below and on Page 22. Light Lens (1) Transmitters {2) Sprocket Rail Touc.
Start By Reading These Impo ant Safety Rules THIS SAFETY ALERT SYMBOL MEANS CAUTION -- PERSONAL SAFETY OR PROPERTY DAMAGE INSTRUCTION. READ THESE INSTRUCTIONS CAREFULLY° THIS GARAGE DOOR OPENER IS DESIGNED AND TESTED TO OFFER REASONABLY SAFE SERVICE PROVIDED IT IS INSTALLED AND OPERATED IN STRICT ACCORDANCE WITH TH E FOLLOWING SAFETY INSTRUCTIONS.
Operation of Your Opener CAUTION e BEFORE YOU PROCEED, PLEASE READ THE SAFETY RULES ON PAGE 4 AND OPERATING INSTRUCTIONS ON THIS PAGE CAREFULLY. e TO AVOID DIFFICULTY DURING INSTALLATION, DO NOT RUN OPENER UNTIL INSTRUCTED TO DO SO. • DO NOT PERMIT CHILDREN TO PLAY IN DOOR AREA.
Assembly TO AVOID INSTALLATION DIFFICULTIES, DO NOT RUN THE GARAGE DOOR OPENER UNTIL YOU ARE INSTRUCTED TO DO SO. ST _: P "1 Assemble Tee Rail & Attach Cable Pulley Bracket TEE RAIL BACK (TO CHASSIS) CAUTION: Do not tighten the lock nuts until bolt necks are seated in square holes.
Assernbiy STE P 2 Install Trolley & Attach Chain Retainer Bracket As a temporary stop, insert a screwdriver into hole in front end of Tee rail as shown.
Assembly STE P 4 I.stall Chain and Cable DO NOT REMOVE CHAIN AND CABLE FROM CARTON Detach cable from side of carton and fasten to trolley with a master link from coin envelope MASTER LINK PROCEDURE: Push pins of master link bar through loop of cable and hole in flat end of trolley shaft (A) Push cap over pins and onto notches.
Assembly STE P 5 Tighten the Chain and Cable Loosen Tighten Inner Outer Nut Nut Trolley Chain J Base of Tee Rail " 1/2 Inch CAUTION: Keep the chain from twisting as nuts are turned.
installation STE P 1 Position & Install Header Bracket Installation procedures vary according to garage door types. Follow onlytbose instructions which applyto your door as illustrated below.
installation STE P 2 A.ach Tee Rail to Header Bracket Ring Orpin I Clevis Pin @/_ Cotter 5/16 'x2-3/4 Fastener g Malerial PROCEDURE: Position opener chassis on garage floor below header bracket.
installation STEP 4 Hang Opener Chassis THE OPENER CHASSIS MUST BE SECURELY FASTENED TO A STRUCTURAL SUPPORTOF GARAGE. Three representative installations are shown. You rs may be different. Hanging brackets should be angled (Fig. 1 ) or crossed (Fig. 2) to provide rigid support On finished ceilings (Fig.
LOCATE WALL PUSH BUTTON (OR ANY ADDITIONAL PUSH BUTTONS) WHERE GARAGE DOOR IS VISIBLE, AWAY FROM DOOR AND DOOR HARDWARE AND OUT OF THE REACH OF CHILDREN. SERIOUS PERSONAL INJURY FROM A MOVING GARAGE DOOR MAY RESULT FROM MIS- USE OF THE OPENER° DO NOT ALLOW CHILDREN TO OPERATE WALL PUSH BUTTON(S) OR THE TRANSMITTER.
Installation STE P 7 Install Light and Lens PROCEDURE: Install a light bulb, (75 Watts Max- imum) in socket as shown The light will turn on and remain lit for 4-!/2 minutes when power is connected After 4-1/2 minutes it will turn off If light bulb burns out prematurely due to vibra- tion, replace with a "rough service" bulb.
Installation STE P 9 Install Door Bracket and Plate Follow instructions which apply to your door type as illustrated below TO PREVENT DAMAGE TO LIGHTWEIGHT GARAGE DOORS, ALWAYS REIN FORCETHE INSIDE OF DOOR--BOTH VERTICALLY AND HORIZONTALLY--WITH 2x4 BOARDS OR ANGLE IRON.
installation STE P 10 Connect Door Arm to Trolley Follow only those instructions which apply to your door type SECTIONAL DOOR INSTALLATION ONLY FIG, A. Make sure garage door is closed tight, Connect straight door arm section to trolley with a clevis pin.
Adjustment STEP 1 Adjust UP and DOWN Limits LIMIT ADJUSTMENT settings regulate the points at which Limit the door will stop when moving up or down w_-_ "Adjustment NOTE: Door STOPS in UP direction if anything inter- _ o _'_"_ Screws fereswithdoortraveI.
Adjustment STEP 3 Test Safety Reverse System TH E SAFETY REVERSE SYSTEM TEST IS IM PORTANT. THE GARAGE DOOR MUSTREVERSE ON CONTACT WITH A ONE INCH OBSTACLE PLACED ON THE FLOOR. FAILURE TO PRO- PERLY ADJUST OPENER MAY RESULT IN SERIOUS PERSONAL INJURY FROM A CLOSING GARAGE DOOR.
Radio Controls Your 3-channel transmitter(s) will operate more than one garage door opener, if desired, Also, refer to the catalog packed with your opener for remote light products which can be operated by the additional push buttons on the transmitter(s).
Having a Problem? SITUATION PROBABLE CAUSE & SOLUTION OPENER DOESN'T OPERATE FROM EITHER WALL PUSH SUTTON OR TRANSMITTER 1. Have you disengaged all door locks? Review Step 8, Page 14 2.
Having a Problem? (Continued) SITUATION DOOR WON'T CLOSE PROBABLE CAUSE & SOLUTION i ,i I i,ii .... ii I 1 The infrared Reversing Sensor (if you have instaIJed this accessory} may be misaligned or obstructed.
Repair Parts RAI L ASSEMBLY PARTS LIST KEY PART NO. NO. DESCRIPTION I 1 2 3 4 5 6 7 8 1A995 Master link kit 41 B2617 Outer trolley 41 B2771 Inner trolley 12A197 Chain retainer bracket 2B313 Tee ratFce.
Repair Parts Chassis Assembly Parts List 21 18 16 15' 14 3 11 12 6 7 KEY PART NO. NO. DESCRIPTION 3 4 5 6 7 6 31 C290 Sprocket cover 41 A2627 Gear and sprocket assy Complete with: Spring washer T.
S=FiA! S / i; Garage Door Opener Models: 139.53403 139o5341 3 139=53606 139o5361 0 Owners Manual HOW TO ORDER REPAIR PARTS Now that you have purchased your Sears Garage Door Opener, should you ever ne.
Een belangrijk punt na aankoop van elk apparaat Craftsman 139.53610 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Craftsman 139.53610 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Craftsman 139.53610 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Craftsman 139.53610 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Craftsman 139.53610 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Craftsman 139.53610 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Craftsman 139.53610 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Craftsman 139.53610 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
