Gebruiksaanwijzing /service van het product 320.17541 van de fabrikant Craftsman
Ga naar pagina of 40
Operator's Manual 9.5 Amp 1314 Peak HP F=xed Base Router Model No. 320.17541 0(_)us DOUBLE INSULATED CAUTION Read, understand and follow atl Safety Rules and Operating Instructions in this Manual before using this product. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.
Warranty ..................................................................................................... Page 2 Safety Symbols ........................................................................................... Page 3 Safety Instructions .
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The symbol warnings DO NOT by themselves eliminate any danger. The instructions and warnings they give are no substitutes for proper accident prevention measures.
Z_ WARNING: BE SURE to read and understand all instructions in this manual before using this router. Failure to follow all instructions may result electric shock, fire and/or serious personal injury. WORK AREA SAFETY 1. Keep your work area clean and well lit.
TOOL USE AND CARE SAFETY Z_ WARNING: BE SURE to read and understand all instructions before operating this router. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. 1. ALWAYS use clamps or other practical ways to secure and support the workpiece to a stable platform.
ELECTRICAL SAFETY cont. 3. BEFORE plugging in the tool, BE SURE that the outlet voltage supplied is within the voltage marked on the tool's data plate.
SERVICE SAFETY I. If any part of this router is missing or should break, bend, or fail in any way; or should any electrical component fail to perform properly: SHUT OFF the power switch and remove the router plug from the power source and have the missing, damaged or failed parts replaced BEFORE resuming operation_ 2.
SAFETY RULES FOR ROUTERS cont. I3. MAKE SURE the cutter bit is not in contact with the workpiece before the switch is turned on.The bit must ALWAYS be running at full speed before contacting the workpiece. 14_ KEEP HANDS CLEAR OF CUTTER BIT when motor is running to prevent personal injury.
A WARNING: Use of this tool can generate dust containing chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints° ° Crystalline silica from bricks and cement and other masonry products o Arsenic and chromium, from chemically treated lumber.
ADDITIONAL RULES FOR SAFE OPERATION cont. 7o ALWAYS check the tool for damaged parts. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine if it will operate properly and perform its intended function.
PARTSLIST (Fig. 1) 1. Fixed Base and Motor with 1/2-in.Collet/Nut (_ 2. Sawdust Extraction Hood 3. 2 Screws _p (for attaching Hood) _p 4. 1/4-in. Collet/Nut 5. Collet/Nut Wrench KNOWYOUR FIXED BASE ROUTER (Fig. 2) I OTE: Before attempting to use your router, familiarize yourself with all of the operating features and safety requirements.
KNOWYOUR FIXED BASE ROUTER cont. (Fig. 2) This Fixed Base Router has the following features: 1. Powerful, 9.5 Amp Soft Start Motor develops 13/4 Peak HP to handle most routing jobs 2. Single speed 25,000 RPM (no-load speed) helps provide a quality finish in most materials 3.
KNOW YOUR FIXED BASE ROUTER cont. (Fig. 2) Dve Tool Indicator" Light Motor Housing Top Cap Quick Clamp Motor Changing System Motor Housing Milled Cast Aluminum for Exact Fit Fixed Base Handles Sp.
Rating ,,, , No-load Speed , i ,i ,,,,,,,,,,,,,, , , ,,,,,, ....... Peak HP , ,,,, ,,,,,, i,u,,, Input , J,t,i Collets/Nuts and Cutter Bi't 's'hank Diameters ............ ,,p, ,, ,, ,,, Fixed Base Diameter ,, ,,,,,.,., Sub Base Opening (Diameter for cutter bit use) .
INSTALLING AND REMOVING THE CUTTING BIT (Figs. 3, 4 and 4a) X,,./ _,,. Nut coHet Spindle Lock Fig. 3 INSTALLING THE CUTTER BIT 1o Turn motor off and unplug from power source, 2. Remove motor housing from fixed base. I F, 4 Fig. 4a _._ Cutters NOTE: See instructions on removing and installing the motor housing from the fixed base on pages 17.
REMOVING THE CUTTER BIT (Figs. 3 and 4 see page 15) 1. Turn motor off and unplug from power source_ 2. Remove motor from fixed base. 3. Set the motor upside down on its top cap, with collet/nut pointing up.. 4. Press spindle lock button to engage and lock the spindle shaft and cotlet/nut, (Fig.
INSTALLING ROUTER MOTOR IN BASE (Fig. 5) t, Turn motor off and unplug from power source. 2. Place fixed base on flat surface° 3,_ With back of fixed base facing you, open motor clamp (A) 4.
ADJUSTING DEPTH OF CUT WARNING: Your router should NEVER BE TURNED ON or be connected to the power source when you are assembling parts, making adjustments, installing or removing collets/ nuts, cutter bits, cleaning or when it is not in use. Disconnecting the router will prevent accidental starting, which could cause serious personal injury.
To Adjust Depth (Figs. 6 and 6a) 2_ 3_ 4_ . . 74 8_ Turn motor off and unplug from power source° Place router on a flat, level surface with back of fixed base facing you° Open Motor Clamp (A).
Deep Cuts The proper cutting depth, (for each pass), is always determined by the material, the cutter bit size and type, and the power of the motor. Always make several progressively deeper cuts by starting at one depth and then make several passes, each time increasing the cutting depth until your desired depth is reached.
LED WORKLIGHTS (Fig. 8) Your router motor has 3 built-in worklights located around the collet/nut to provide high visibility of workpiece when cutting. These lights are always "On" when the toggle switch is in the "On "position. Fig.
EDGE ROUTING OR INTERNAL ROUTING For ease of operation and to maintain proper control, your router has two handles, one on each side of the router base.
INTERNAL ROUTING (Figs. 11, 11a, 11b and 12) 1., With depth-of-cut set, tilt router and place on workpiece with leading edge of sub-base contacting workpiece first (Fig. 11)_ 2. Turn motor "On" and let motor build up to its full speed, being careful not to let cutter bit contact workpiece.
FREEHAND ROUTING WITH THE FIXED BASE (Fig. 13) WARNING: Do not use large cutter bits for freehand routing. Use of large cutter bits when freehand routing could cause loss of control or create other hazardous conditions that could result in personal injury.
EDGING WITH A PILOT BIT (Figs. 14 and 14a) The arbor-type bits with pilots are excellent for edge shaping of any workpiece edge that is either straight, or curved at a curvature as great or greater than the radius of the bit to be used.
FEEDING THE ROUTER (Fig. 15) The secret to professional routing is in making a careful set-up for the cut, selecting the proper depth of cut, knowing how the cutter bit reacts in your workpiece, and the rate and direction of feed of the router° .< ROUTER EED ® DIRECTION Fig.
DIRECTION OF FEED - INTERNAL CUTS (Figs. '16 and 16a) When making an internal cut, such as a groove, dado or slot, always have the guide you are using with the router (edge guide, straight edge, board guide), on the right-hand side of the router as you make your cut, see Fig_ 16).
RATE OF FEED (Figs. 17 and 17a) The proper rate of feed depends on several factors: the hardness and moisture content of the workpiece, the depth of cut, and the cutting diameter of the bit. When you are cutting shallow grooves in soft woods such as pine, you may use a faster rate of feed.
CHIP SHIELD DEFLECTOR (Fig, 18) _-_ WARNING: ALWAYS wear eye protection. The chip shield deflector is not intended as a safety guard. To remove chip shield from fixed base, press inward on tabs until .
I ] WARNING: To ensure safety and reliability, all repairs should be performed by a qualified service technician at a Sears Service Center. GENERAL Only the parts shown on the parts list are intended for repair or replacement by the customer.
REPLACEMENT OF CARBON BRUSHES (Fig. 20) Replacement brush sets are available through Sears Parts and Repair Centers° !o Unplug the router motor before inspecting or replacing brushes. 2. Replace both carbon brushes when either has less than !/4-in. length of carbon remaining, or if the spring or wire is damaged or burned.
[z_ WARNING: The use of attachments or accessories that are not 1 recommended for this tool might be dangerous and could result in serious injury. I Sears and other Craftsman e outlets offer a large s.
In additionto a wide variety of router bits, Sears also offers accessories such as: Routertables, various templatesets, universalrouter fence with lock knobs (64181), 11 pc. bushingset (64180) and clear sub-base sets; 6pc. fixed base (64182) 6 pco plunge base (64183)o 1/2-in bead and cove 1/16-in.
9.5 Amp / 13/4 Peak HP- MODEL NUMBER 320.17541 The Model Number will be found on the Nameptate_ Always mention the Model Number in all correspondence regarding your too!. Motor Unit ,% # % I I f t ' ' 26 # # # ! t I # I 27 28 28 28 29 70 .,I-31 33 -__l' // .
9.5 Amp / 1314 Peak HP - MODEL NUMBER 320.17541 The Model Number will be found on the Nameplate_ Always mention the Model Number in all correspondence regarding your tool.
9.5 Amp / 1 3/4 Peak HP Fixed Base Router- MODEL NUMBER 320.17541 The Model Number will be found on the Nameplate, Always mention the Model Number in alt correspondence regarding your tool Item No.
9.5 Amp / 1 3/4 Peak HP Fixed Base Router- MODEL NUMBER 320.17541 The Model Number will be found on the Nameplate, Always mention the Model Number in all correspondence regarding your tool, Item No.
38.
39.
Your Home For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts,.
Een belangrijk punt na aankoop van elk apparaat Craftsman 320.17541 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Craftsman 320.17541 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Craftsman 320.17541 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Craftsman 320.17541 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Craftsman 320.17541 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Craftsman 320.17541 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Craftsman 320.17541 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Craftsman 320.17541 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
