Gebruiksaanwijzing /service van het product 358.35181 van de fabrikant Craftsman
Ga naar pagina of 26
Operator's Manual 2.4 cu.in./40cc 2-Cycle GASOLINE CHAIN SAW Model No. 358.351810 - 18 in. Bar • Safety • Assembly • Operation • Maintenance • Parts List • Espar_ol, p, 27 CRAFTSMAN ° WARNING: Read and follow all Safety Rules and Operating Instructions before first use of this product.
Warranty 2 Storage 20 Safety Rules 2 Troubleshooting Tabie 21 Assembly 6 Emissions Statement 23 Operation 7 Parts List 25 Maintenance 14 Spanish 27 Service and Adjustments 17 Parts & Ordering Back.
OPERATE YOUR SAW SAFELY • Do not operate a chain saw with one hand. Serious injury tothe operator, heipers, bystanders or any combina- tion of these persons may result from one-handed operation. Achain saw is intended for two-handed use. • Operate the chain saw only in a welt- ventilated outdoor area.
_ILWARNING: Avoid kickback which can resuIt in serious injury. Kickback is the backward, upward or sudden forward motion of the guide bar occurring when the saw chain near the upper tip of the guide bar contacts any object such as a log or branch, or when the wood closes in and pinches the saw chain in the cut.
• Position your left hand on the front handtebar so itis in a straight tine with your right hand on the rear handle when making bucking cuts. Never reverse right and left hand positions for any type of cutting. • Stand with your weight evenly bal- anced on both feet.
This unit is not equipped with an anti- vibration system and is intended for occasional use only. SAFETY NOTICE: Exposure to vibra- tions through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or abnormal swell- ings.
KNOW YOUR CHAIN SAW READ THIS OPERATOR'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHAIN SAW. Compare the ittustrations with your unit to familiarize yourself with the location of the various controis and adjustments.
BEFORE STARTING ENGINE _ll, WARNING: Muffter is very hot during and after use. Do not touch the muffIer or allow combustible material such as dry grass or fuel to do so.
_ILWARNING: Do not attempt to throw or drop-start the chain saw, Doing so witt put the operator at risk of serious injury due to loss of controI of the chain saw. IMPORTANT POINTS TO REMEMBER When puIIing the starter rope, do not use the full extent of the rope as this can cause the rope to break.
CHAIN BRAKE _b'WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake must be replaced if any part is worn to tess than 0.020" (0.
TREE FELLING TECHNIQUES _II, WARNING: Check for broken or dead branches which can fall while cut- ting causing serious injury. Do not cut near buildings or electrical wires if you do not know the direction of tree falt, nor cut at night since you will not be aIe to see well, nor during bad weather such as rain, snow, or strong winds, etc.
kickback and chain damage, use wood or p}astic wedges, but never steel or iron wedges. • Be alert to signs that the tree is ready to fail: cracking sounds, widen- ing of the feI}ing cut, or movement in the upper branches. • As tree starts to fall stop saw, put it down, and get away quickly on your ptanned retreat path.
• Your first cut should extend 1/3 of the diameter of the log. • Finish with your second cut. Using a log for support f/1 st Cut Using a support stand 2 nd Cut X L LIMBING AND PRUNING _IIWARNING: Be alert for and guard against kickback.
CUSTOMER RESPONSIBILITIES _WARNING: Disconnect the spark plug before performing maintenance except for carburetor adjustments. Filt in dates as you complete Before After Ever Every Service regular service Use Use 5 hrs 25 hrs. Yeady Dates Check for damaged/worn parts .
Guide Ear _ J Screwdriver Adjusting Wheel Knob 2. Lift lever on bar knob and turn counterclockwise 1 turn to loosen bar clamp. CRAF LOOSEN 3. Turn adjusting wheel (downward direction) to tension chain until chain solidly contacts bottom of guide bar rail.
After each use, ensure ON/STOP switch is in the STOP position, then clean all sawdust from the guide bar and sprocket hole. To maintain guide bar: • Move ON/STOP switch toSTOR • Loosen and remove bar nuts and clutch cover. Remove bar and chain from saw.
Replace the spark arresting screen if breaks occur. Spark Exhaust Arresting Outlet Screen Cover z Nut Muffler CLEANING THE SPARK ARREST- ING SCREEN Cleaning is required every 25 hours of operation or annually, whichever comes first. 1. Loosen and remove the nut from the exhaust outlet cover.
3. Sharpen cutters. • To sharpen the cutters, position the file holder level (90 ° ) so that it rests on the top edges of the cut- ter and depth gauge.
2. Loosen and remove bar knob com- pletely by lifting tever and turning counterclockwise, CRRF LOOSEN 3. Loosen chain tension by turning adjusting wheel (upward direction), Remove clutch cover. Bar Knob 4. Slide guide bar on bar bolts until guide bar stops against clutch drum sprocket.
Idle Speed-T Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow. Adjust speed until engine runs without chain movement (idle too fast) or stalling (idle too slow). The idle speed screw is tocated in the area above the primer bulb and is labeled T.
TROUBLESHOOTING TABLE _, WARNING: Always stop unit and disconnect spark plug before perform- ing all of the recommended remedies below except remedies that require operation of the unit. TROUBLE CAUSE Engine will not start or will run only a few seconds after starting.
TROUBLESHOOTING TABLE - Continued TROUBLE Chain does not move when en- gine is acceler- ated Chain clatters or cuts roughty. CAUSE t. Chain tension too tight. 2. Carburetor requires adjustment 3. Guide bar rails pinched. 4-.C_utch slipping 5. Chain brake engaged.
YOUR WARRANTY RIGHTS AND OBLIGATIONS: The U.S. Environ- mental Protection Agency/California Air Resources Board and Sears, Roe- buck and Co., U.S.A., are pieased to explain the emissions control system warranty on your year 2007 and later small off-road engine.
ures of warranted parts caused by the use of add-on or modified parts. HOW TO FILE A CLAIM: If you have any questions regarding your warranty rights and responsibi$ities, you should contact your nearest authorized ser- vice center or call Sears at 1-800-469-4683.
REPAIR PARTS 8EARS CHAINSAW MODEL 358.351810 16 / 36 28 26 44 46 45 514 WARNING A" repairs, adju,;trnent6 and I maintenance not described in 52 Lhe Operato;'s Mar=uai must be performed by qualifieG 9e_lce personnel Ref Pa_ No. De_¢ri_ion Ref Pa_ No.
REPAIR PARTS 39 SEARS CHAtNSAW MODEL 358351810 9 10 WARNING All repairs, ad}ustments and maintenance not described in the Operator's Manual must be pelfolmed by qualified sewice pe_sonneE 2O 24 4.
Een belangrijk punt na aankoop van elk apparaat Craftsman 358.35181 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Craftsman 358.35181 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Craftsman 358.35181 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Craftsman 358.35181 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Craftsman 358.35181 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Craftsman 358.35181 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Craftsman 358.35181 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Craftsman 358.35181 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
