Gebruiksaanwijzing /service van het product 580.76225 van de fabrikant Craftsman
Ga naar pagina of 16
SmARS Owner's Manual CRAFTSMAN ° 6.0 HORSEPOWER 2250 PSI 2.2 GPM HIGH PRESSURE WASHER Model No. 580.762250 CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. PRESSURE WASHER / CUSTOMER HEUPUNE HOURS: Mon,- Fri.
SAFETY RULES .......................... 2-3 ASSEMBLY .............................. 4-5 OPERATION ............................ 6-10 MAINTENANCE ...................... .V.!1,131 _ ............. 14 SERVICE AND ADJUSTMENTS ._. ..... STORAGE .............
• Units with broken Or missing parts, or without protective housing or covers should NEVER be operated. • The muffler and air cleaner must be installed and in good condition before operating the Pressure Washer. These components act as spark arrestors if the engine backfires.
CARTON CONTENTS The following parts are shipped loose with your pressure washer: • Main Unit -- pressure washer with wheels and guide handle • Product Introduction Video • Nozzle Cleaner Kit •.
• • Place assembled spray gun on holder. Cut tie wrap from high pressure hose. Connect high pressure hose to gun with either two adjustable wrenchs or one 11/16" and one 7/8" wrench. Remove plastic cap and connect high pressure hose to pump.
KNOW YOUR HIGH PRESSURE WASHER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR HIGH PRESSURE WASHER, Compare the illustrationswith your high pressure washer to familiarize yourself with the locations of various controls and adjustments.
HOW TO USE YOUR PRESSURE WASHER IF YOU HAVE ANY PROBLEMS operating your pres- sure washer, please call the pressure washer helpline at 1-800-222-3136. A WARNING NEVER adjust spray pattern when spraying. NEVER put hands in front of spray nozzle to adjust spray pattern.
Toapply detergent follow these steps: • Prepare the detergent solution as required by the job. • Hang the detergent solution on the "J" hook on the wire form on the guide handle.
BEFORE STARTING THE PRESSURE WASHER To operate the engine you will need to do the following: ENGINE OIL A 20 oz. bottle of SAE 30 weight oil is included in the parts carton. Fill engine crankcase with recommended oil until oil level is at FULL point on dipstick.
TO START YOUR PRESSURE WASHER You have assembled your high pressure washer and have prepared the engine for starting. You are now ready to clean your car, boat or the outside of a buildingor whatever you plan to clean: The best way to start your engine-powered pressure washer for the first time is to follow these instructions step-by-step.
CUSTOMER RESPONSIBILITIES MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE HOURLY OPERATING INTERVAL REGULAR SERVICE Every 25 Every 50 Every100 Before Each Hours or Hours or Hours or MAINTENANCE TASK Use Yearly Yearly Yearly SERVICE DATES PRESSURE WASHER Check/clean water inlet screen onquick-connect.
BEFORE EACH USE • Checkwater inlet screen for damage. • Check • Check o high pressure hose for leaks. detergent inlet hose and filter for damage.
CLEAN/REPLACE SPARK PLUG Change the spark plug every 100 hours of operation or once each year, whichever comes first. This will help your engine to start easier and run better. Replace with Champion RJ-8C or equivalent type spark plug. Set spark plug gap 0.
CARBURETOR If you think your carburetor needs adjusting, see your nearest Sears Service dealer. Engine performance may be affected above 4,000 feet in altitude.
AFTER EACH USE Water should not remain in the unit for long periods of time. Sediments of minerals can deposit on pump parts and "freeze" pump action. Follow these procedures after every Use: • Flush detergent hose by placing the injector filter into a pail of clear water while running Pressure Washer with nozzle in low pressure mode.
PROBLEM Pump has following problems: failure to produce pressure, erratic pressure, chattering, lossof pressure, low water volume. CAUSE 1. Nozzle in lowpressure mode. 2. Water inlet is blocked. 3. Inadequate water supply 4. Inlet hoseis kinked or leaking 5.
Een belangrijk punt na aankoop van elk apparaat Craftsman 580.76225 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Craftsman 580.76225 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Craftsman 580.76225 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Craftsman 580.76225 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Craftsman 580.76225 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Craftsman 580.76225 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Craftsman 580.76225 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Craftsman 580.76225 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
