Gebruiksaanwijzing /service van het product 1345 SWE van de fabrikant Cub Cadet
Ga naar pagina of 28
O PERA T OR’S M ANU AL IMPORT ANT : READ SAFETY RULES AND INSTRUCTIONS CAREFULL Y CUB CADET CORP . P .O . BO X 368023 CLEVELAND , OHIO 44136-9722 45” Snow Thr ower Model 13 45 SWE PRINTED IN U .
2 TABLE OF CONTENTS Content Page Important Safe Ope ration Practices ................. ............. ................... .................. 3 Assemb ling Your Sno w Thrower ............... ............. ................... ................... ..... 5 Knowing Your Sno w Thrower .
3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES This symb ol point s out important safety ins truction s which, if not foll owed, coul d endanger the personal safety and/ or property of yourse lf and others . Read and foll ow all instruc tions in th is manual be fore attempting to operate this machine.
4 5. Never run an eng ine indoors or in a poorl y ventil ated area. Engine ex haust co ntains carbo n monoxide , an odorless and deadly g as. 6. Do not operate machin e while under the influ ence of alcohol or drugs. 7. Muffler a nd eng ine becom e hot and can c ause a b urn.
5 SECTION 2: ASSEMBLING YOUR SNOW THROWER Unpacking • Remove s taples from the top, sides, and end s of the shi pping cra te. • Set panel s aside to avoid tire pu nctures or personal injury . • Remove an d discard pl astic bag th at covers uni t.
6 • Tigh ten the tw o win g nuts alre ady in plac e on th e upper hol es and secu re the han dles firml y. Refer to Figure 2. • Slide th e shift rod conn ector down over the end of the lower shi ft rod as sh own in Figure 2. Tap t he conne ctor un til it locks on the lower shif t rod.
7 If adjustme nt is necessa ry, procee d as follows: • Loosen th e jam nut and thread the cable in (for less slack ) or out (for more s lack) a s necess ary. See Figure 7. Figure 7 • Rech eck adjustme nt; readju st as necess ary and tighte n the jam nut.
8 SECTION 3: KNOWING YOUR SNOW THROW ER WARNI NG: Be familiar with all the c ontrols an d their p roper oper ation. Kn ow how to sto p the mach ine and disen gage them quic kly. Figure 9 Tract ion Control / Auge r Cont rol Lock The tracti on control i s located on th e right handl e.
9 Wheel Steering Controls The left a nd right wheel steering co ntrols are located on the unders ide of the handl es and are use d to assist in steerin g the snow thro wer. • Squeez e the right wheel s teering control when turning rig ht; squeeze the left contr ol when turning left.
10 • If your house wir ing system is not a three-wire grounded system, do not use th is electric starter unde r any co ndi tio ns. • If your home electr ical system is grounded, bu t a three-h ole receptac le is not av ailable, one sh ould be install ed by a licens ed electric ian before using the el ectri c star te r.
11 WARNING: The temperatu re of the muffler and the s urroundin g areas may exc eed 150 ° F. Av oid thes e areas. • For the mos t effici ent snow removal, remo ve sn ow immed iately afte r it falls. • Discha rge snow dow nwind whenever possible. • Slight ly overlap ea ch pre vious clea ning path.
12 • Rotate th e ferrule up or down o n the s hift rod a s necessar y until the ferr ule lines up wit h the upper hole in the sh ift lever . Refer to Figur e 12. • Insert ferrule from the lef t side of the sno w thrower into the upper hole. • Reinsta ll the hairpin clip and the washe r.
13 Fig ure 1 4 Discharge Chute The base of the discha rge chute an d the spira ls on the chute cr ank shoul d be lubricate d at least eve ry 25 hours of use. W hen applyi ng the lubric ation, apply the lubric ant as shown in Figure 14 to the point under the base of the ch ute and where th e spirals c ontact the dischar ge chute.
14 SECTION 7: SERVICING YOUR SNOW THROWER WARN ING: Before servicing , repairi ng, or insp ecting, d isengage all clu tch l evers and stop e ngine. Wa it until all moving parts ha ve come to a compl ete stop. Disc onnect spark plug wir e and groun d it agai nst the en gine to prevent unintend ed starti ng.
15 Fig ure 1 8 Auger B elt • Remo ve the co tte r pin an d wash er fro m the ferru le in ord er to d isconnect the aug er idler rod f rom the brake brac ket assem bly as shown in Figure 19 . • Slip the auger control belt (the front be lt) off the engin e pulley.
16 Fig ure 2 1 • Attach the “ Z ” fitting of the cable int o the brake bracke t assembly. Re fer to Figure 19. • Slip the auger contro l belt over en gine pulle y. • Inse rt ferrule on auger idler rod in to bracket assembl y and secu re with flat washe r and cotter pin.
17 • Reasse mble the new fr iction wheel r ubber to the frictio n wheel assem bly, tighte ning the si x screws in rotation and with equal for ce. It is impor tant to assembl e the rubber on the friction wheel symmetr ically for proper funct ioning.
18 SECTION 9: TROUBLESHOOTING Proble m Caus e Rem edy Engine fai ls to start. 1. Fuel tan k em pty, o r stale fuel. 2. Blocked fuel line. 3. Choke not i n ON pos i tion 4. Faulty sp ark plug. 5. Safety k ey not i n igni tion switc h on e ngine. 6. Spark plug wire dis connected.
19 SECTION 10: PARTS LIST FOR MODEL 1345 SWE.
20 24 29 29 30 20 39 1 3 2 4 5 5 5 7 6 8 25 25 40 42 8 18 31 8 25 43 29 27 13 17 13 9 14 25 26 34 34 26 32 14 14 21 21 16 10 23 12 13 35 11 37 25 13 22 19 13 33 25 14 41 28 15 36 38 44 45 46 47 48 13 14 25 49 52 50 51 53 54 55 56 57 58 NOTE: For pain ted pa rts , please refe r to the list of colo r codes bel ow.
21 MODEL 1345 SWE Ref. No. P ar t No. P art De scription 1. 05244A Bearing H ousing 2. 618-0281 A Bracket Ass embly: Auge r Break 3. 684-0090 A Impell er Assembly: 16 ” 4. 710- 0371 Hex Lo ck Bol t 5/16- 18 x .8 75 ” 5. 710-0451 Carriag e Bolt 5/1 6-18 x .
22 MODEL 1345 SWE 18 12 76 17 8 16 9 11 45 49 66 4 35 35 36 45 45 45 10 18 18 24 73 55 32 42 5 54 39 23 34 6 67 14 51 27 75 71 64 58 22 21 55 29 13 46 60 55 56 52 37 22 56 2 46 46 33 13 29 46 40 57 38.
23 MODEL 1345 SWE Ref. No. P ar t No. P art De scription 1. 05523 Support Bra c ket: Pivot 2. 618-0278 Bush Ass embly 3. 618-0279 Dogg Ass embly LH 4. 618-0280 Dogg Ass embly RH 5. 618-0282 B Shift Assem bly 6. 618-0296 Whee l Bearing Assembly 7. 684-0115 Support Bra cket Ass embly 8.
24 MODEL 1345 SWE 1 1 2 3 4 5 4 5 19 19 19 19 6 6 7 7 8 9 9 10 21 13 29 11 22 24 31 17 27 23 15 26 21 15 14 25 16 18 22 11 20 15 12 28 30 15 23 13 21 33 32 32 A A A A 33 34 34 35 35 36 37 38 39 40 41 42 43 44 NOTE: For painted p a rts , please refe r to the list of color code s below.
25 MODEL 1345 SWE Ref. No. P ar t No. P art Description 1. 646-0012 Cable As sembly : Auger/Dri ve Engagemen t 2. 684-0053A Chute C rank Assembly 3. 705-5266 Chute C rank Bracket 4. 710-0216 Hex Scre w 3/8-16 x .75 ” 5. 710-0347 Hex Screw3/8 -16 x 1.
26 MODEL 1345 SWE Ref. No. P art No. Description 1. 07386 W asher 2. 684-012 3A Belt Cov er Brack et Assemb ly 3. 710- 0191 Hex Screw 3/8-24 x 1.25 ” 4. 710- 0237 Hex Screw 5/16 -24 x .625 ” 5. 710- 0502A TT Sems Scre w 6. 710- 0607 TT Screw 5/16-18 x 0.
27 MODEL 1345 SWE Ref. No. Part No. Description 1. 710-027 6 C arriage S crew 2. 710-045 8 Carriage B olt 5/16-18 x 1.7 5 ” 3. 710- 0805 Hex Bolt 5/16- 18 x 1. 5 ” 4. 710-089 6 Hex A B Screw 1/ 4-14 x .625 ” 5. 710-301 5 Hex Screw 1/4 -20 x .75 ” 6.
28 MANUF A CTURER ’ S LIMITED W ARRAN TY FOR: TWO-YEAR RESIDENTIAL ONE-YEAR COMMERCIAL Prope r maintenance of your Cub Cadet equipm ent is the owner ’ s respo nsibility . Follow t he instr uctions i n your operator ’ s manual for correc t lubrica nts and maintenan ce schedul e.
Een belangrijk punt na aankoop van elk apparaat Cub Cadet 1345 SWE (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Cub Cadet 1345 SWE heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Cub Cadet 1345 SWE vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Cub Cadet 1345 SWE leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Cub Cadet 1345 SWE krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Cub Cadet 1345 SWE bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Cub Cadet 1345 SWE kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Cub Cadet 1345 SWE . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
