Gebruiksaanwijzing /service van het product DV-K580NZ-T van de fabrikant Daewoo
Ga naar pagina of 80
Service Manual S/M No. : VK580NTEF0 Jan. 2000 DAEWOO ELECTRONICS CO., LTD. http : //svc.dwe.co.kr TIME LAPSE VCR Model: DV-K580NZ-T.
1 TABLE OF CONTENTS SAFETY&PRECAUTIONS ............................................................................................... 2 EXTERNAL VIEWS ...............................................................................................
2 SAFETY&PRECAUTIONS SAFETY CHECK AFTER SERVING Examine the area surrounding the repaired location for damage or deterioration. Observe that screw, parts and wires have been returned to original positions. Afterwards, perform the following tests and conform the specified values in order to verify compliance whit safety standards.
3 SAFETY&PRECAUTIONS 4. Leakage current test Confirm specified or lower leakage current between B(earth ground, power cord plug prongs) and externally exposed accessi- ble parts (RF terminals, antenna terminals, video and audio input output terminals, microphone jacks, earphone jacks, etc.
4 1. FRONT VIEWS FUNCTION EXTERNAL VIEWS 1) STOP button 2) REC button 3) REC CHECK button 4) EJECT button 5) CASSETTE LOADING DOOR 6) DISPLAY PANEL 7) PLAY button 8) REW button 9) FF button 10) PAUSE/.
5 EXTERNAL VIEWS 2. REAR VIEWS FUNCTION 1) AC POWER CORD 2) WARNING OUT terminal 3) SERIES IN terminal 4) COM terminal 5) SERIES OUT terminal 6) SW OUT terminal 7) VIDEO OUT jack 8) VIDEO IN jack 9) A.
6 ELECTRICAL ADJUSTMENT 1. SERVO/SYSCON CIRCUIT ADJUSTMENT METHOD v VIDEO HEAD SWITCHING POSITION v CONNECTION METHOD v ADJUSTMENT PROCEDURE 1) Play back the test tape. 2) Set the oscilloscope in the chop mode connect the CH1 to SW pulse(PT501 (r)PIN), the CH2 to TJ396(video out) with CH1 triggering.
7 ELECTRICAL ADJUSTMENT 2. VIDEO CIRCUIT ADJUSTMENT METHOD (1) EE LEVEL v CONNECTION METHOD v ADJUSTMENT PROCEDURE 1) Supply the Color Bar Signal to the VIDEO IN JACK, and set the VCR to the STOP mode. 2) Connect the oscilloscope to TJ396 and trigger the scope with a composite sync signal at TJ302.
8 ELECTRICAL ADJUSTMENT (2) PLAYBACK Y-SIGNAL OUTPUT LEVEL v CONNECTION METHOD v ADJUSTMENT PROCEDURE 1) Playback the COLOR BAR Test tape (DN-1). 2) Connect the oscilloscope to TJ396 and trigger the scope with a composite sync signal at TJ302. 3) Adjust R396 to obtain 2.
9 ELECTRICAL ADJUSTMENT (3) SYNC TIP FREQUENCY v CONNECTION METHOD v ADJUSTMENT PROCEDURE 1) Set the VCR to STOP mode without Video Signal.(VIDEO IN JACK is shorted with Ground) 2) Connect the frequency counter TJ391. 3) After Inserting Rec Tape REC in SP Mode 4) Adjust R391 to obtain 4.
10 ELECTRICAL ADJUSTMENT (4) FM DEVIATION v CONNECTION METHOD v ADJUSTMENT PROCEDURE 1) Supply the Color Bar Signal to the VIDEO IN JACK, and set the VCR to the REC mode. 2) Connect the oscilloscope to TJ396 and trigger scope with a composite sync signal at TJ302.
11 ELECTRICAL ADJUSTMENT (5) C RECORD CURRENT v CONNECTION METHOD v ADJUSTMENT PROCEDURE 1) Supply the Color Bar Signal to the VIDEO IN JACK, and set the VCR to the REC mode. 2) Connect the oscilloscope to TJ491 and trigger the scope with a composite sync signal at TJ302.
12 ELECTRICAL ADJUSTMENT (6) Y RECORD CURRENT v CONNECTION METHOD v ADJUSTMENT PROCEDURE 1) Supply the Color Bar Signal to the VIDEO IN JACK. 2) After Inserting a Rec T ape, Rec in SP MODE. 3) Connect the oscilloscope to TJ491 and trigger the scope with a compos- ite sync signal at TJ302.
13 ELECTRICAL ADJUSTMENT 3. AUDIO CIRCUIT ADJUSTMENT METHOD (1) AUDIO RECORD BIAS v CONNECTION METHOD v ADJUSTMENT PROCEDURE 1) Supply the signal in the OPEN mode. 2) Connect the Audio Level Meter to R01 at the Deck AC Head. 3) After inserting a blank tape, record in SP mode.
14 SPECIFICATIONS Video Signal system NTSC REC/PB System Helical scanning system Tape Width 12.65mm (1/2 inch), VHS Record system of Luminance Signal Frequency modulation record Record system of Color Signal Down converted subcarrier phase shift system Tape Speed (T-120) 2H : 33.
15 TIMELAPSE REC/PB SPEED CHART TAPE MODE TAPE SPEED REMARK REC MODE T-120 EP 24H MODE IS POSSIBLE IN PLAY MODE. SP 2H 24H 36H EP 6H 18H T-160 SP 2.7H 32H 49.
16 CIRCUIT OPERATION 1. VIDEO PART 1-1) EE MODE Video Signal which is output from RL902 is input to pin 37 of IC301 through OSD IC. It is amplified 6dB by AGC, then it is output to pin 34. This output signal is output to Video Jack through RL902 of RELAY IC.
17 CIRCUIT OPERATION 1-3) PB MODE When playing the tape, the signal which is picked up from the tape is amplified 50 dB. Then luminance signal goes to pin 11 and color signal goes to pin 7 through AGC. Luminance signal of pin 11 is input to pin 39 of IC301 through PB EQ cir- cuit in order to match playback characteristic.
18 CIRCUIT OPERATION 2. AUDIO PART 2-1) EE MODE External AUDIO signal which is input to pin 16 of IC201 is output from pin 22 of IC201 after being amplified through ALC and Line Amp. 2-2) REC MODE It will be the REC mode when REC 5V is input to pin 24 of IC201.
19 CIRCUIT OPERATION 3. SERVO SYSCON PART 3-1) BLOCK DIAGRAM DRUM PG FG AMP CAPSTAN SPEED CTL IC501 M37775M5H u-COM PROCESSOR Start end SENSOR & REEL SENSOR LOADING CAM DRIVE CTL AMP VIDEO BLOCK A.
20 CIRCUIT OPERATION 3-2) TIME LAPSE RECORDING METHOD The numbers of VHS 2HOUR (SP), 6HOUR (EP) REC FIELD are 60 field/sec, then it will be 1FRAME = 33.3Ms, 1FIELD = 16.65Ms. CAPSTAN MOTOR FG numbers for Time Lapse are 6HOUR(EP) = 720 numbers/sec, 2HOUR(SP) = 720*3=2160 num- bers/sec.
21 CIRCUIT OPERATION 3-3) TERMINAL PART ALARM INPUT Connect DOOR SW&SENSOR etc and this port will be used for emergency recording by using open/close status. ALARM OUTPUT This port is always triggered during ALARM REC, which is used to inform the outside that time lapse VCR is now perform- ing Alarm Recording.
22 CIRCUIT OPERATION TAPE END OUT When the recording tape ends during recording, end sensor will be detected. This port is used Alarm to outsider until release the end sensor detecting. SW OUTPUT This port is used triggering video signal with external equipment during recording.
23 CIRCUIT OPERATION SERIES INPUT When the series recording proceeds after setting the series recording to “ on ” , this port is used to receive the control signal to the set which will be recorded continuously after pre-recording set. WARNING OUTPUT This port is used to inform emergency status of Time Lapse VCR Set to outsider.
24 TROUBLE SHOOTING FLOW CHART 1. POWER CIRCUIT When changing the parts which are broken first, remove the power plug from the socket and then discharge the voltage across the terminals of C806.
25 TROUBLESHOOTING FLOW CHART B. CHECKING THE SECONDARY CIRCUIT Check each output voltage Check M801. Check any diode which causes no power Check any COIL, or capacitor which causes no power END.
26 TROUBLESHOOTING FLOW CHART 2. SERVO-SYSCON CIRCUIT A. Playback picture is not good Noise appears although adjusting tracking. Check and re-adjust the path of Deck.
27 TROUBLESHOOTING FLOW CHART B. NO NO Playback picture is not good. NO NO Check flow A. YES YES YES YES Noise appears on the screen on the whole. Noise appears on the screen at the bottom Change Drum Ass'y Is Enve. waveform supplied to pin 4 of P T501? Check connector, and Head dust.
28 TROUBLESHOOTING FLOW CHART C. Auto-stop during playback. NO Is reel pulse applied to pin 5 and 6 of IC501? Check reel sensor. NO YES Is D. FG applied to pin 24 of IC501? YES Check IC501.
29 D. TROUBLESHOOTING FLOW CHART Drum M/T loading stops. NO NO Is motor 12V supplied from Ic504 pin7, 8? Check circuit adjacent EVER +12.4V. Check power module.
30 E. TROUBLESHOOTING FLOW CHART YES Check connector and motor. Capstan M/T loading stops. NO YES Is motor 12V supplied? Check power Module. NO Is the input of pin 6 of P501 2.5V~3.5V? Check circuit of R516, R517, R520, C509, C511. YES NO Is pin 4 of P501 2.
31 F . G. TROUBLESHOOTING FLOW CHART Drum M/T and capstan M/T rotate at regular speed. (IN REC MODE) NO Is C. sync applied to pin 93 of IC501? Check C. sync of video IC and pattern. Check motor YES Emergency mode when plugging (power cord) NO YES Is ever 5V applied? Check power Module.
32 TROUBLESHOOTING FLOW CHART H. Cassette is not inserted. NO YES YES YES NO Is motor 12V supplied? Check power Module. NO NO CAM DATA is changed when CST IN? Check connector. Check IC501. Check Deck part. Is 5V supplied at pin 31 of IC501? Check pattern and R572.
33 I. TROUBLESHOOTING FLOW CHART Power compensation does not operate. NO YES YES YES When mains is unplugged, is 3.6V at pin 26,pin 81 of IC501? Check C548, C523, C547, C524. NO Is (sine) signal applied to pin 42 and 43 of IC501? Check X502. NO Is 5V at pin 37 of IC501? Check reset circuit Of IC503.
34 3. VIDEO CIRCUIT A. EE MODE N.G. TROUBLESHOOTING FLOW CHART Is VIDEO signal input Into pin 2 of RL 902? Is E9V supplied at Pin 1 of RL 902? Check terminal. NO YES Check EVRE 9V. NO Is signal output from pin 8 of RL 902? YES Check pin 3 input signal of RL902.
35 B. REC SIGNAL N.G. Check EE mode. NO NO Check method A. YES YES Is REC-Y signal output From pin 40 of IC 301? Is signal input into pin 37 of IC 301? NO NO Is REC-C signal input into pin 12 of IC 401? Is 5V supplied at pin 28 of IC 301? Check Power Circuit.
36 C. PB-Y SIGNAL N.G. Is envelope output from pin 7,11 of IC 401? Is signal input at pin 39 of IC 301? Is 5V supplied at pin 1, 2 of IC 401?. NO YES Check PCB PATTERN and Q408. NO Is signal output from pin 3 of IC 301? YES Check pin 35 Vcc of IC301. NO Check power circuit.
37 D. PB-C SIGNAL N.G. Is color signal output from pin7 of IC 401? Is color signal input into pin 15 of IC 301? Is +5V supplied at pin 1, 2 of IC 401?. NO YES Check Q409, Q414, Q415. NO Is color signal output from pin 27 of IC 301? YES Is C-ROTARY input into pin 41 of IC 301? NO Check power circuit.
38 4. AUDIO CIRCUIT A. TROUBLESHOOTING OF PB MODE YES Check P902 & Audio JACK. No sound in the playback mode. NO YES Is signal input pin 2 of IC 201? Check PJ 201 & Check C207, R208. NO Is 9V applied to pin 7 of IC 201? Check Q801 & POWER.
39 B. TROUBLESHOOTING OF REC MODE YES AC signal put on 70KHz at Base of Q201. No sound in the playback mode after recording. NO YES Is signal input pin 16 of IC 201? Check RL 901 & P 902. NO Is 9V applied to pin 7 of IC 201? Check Q801 & POWER.
40 C. TROUBLESHOOTING OF EE MODE No sound in the EE modes. NO YES Is 9V applied to pin 7 of IC 201? Check Q 801 & POWER. NO Is signal input pin 16 of IC 201? Check RL 901, P902, AudioJACK. YES NO Is signal output pin 22 of IC 201? Check EE(L), IC 201.
41 u-COM PORT DESCRIPTION NO PORT SET PORT NAME DESCRIPTION 1 I/O OUT S OUTPUT Series record output 2 I/O IN S INPUT Series record input 3 I/O OUT C PWM Capstan control 4 I/O OUT D PWM Drum control 5 .
42 39 Xout Xout Xout 16MHz out 40 CLKSET N.C N.C GND 41 Vss N.C N.C GND 42 Xcin Xcin Xcin 32MHz in 43 Xcout Xcout Xcout 32MHz out 44 I/O OUT EE(L) EE LOW 45 I/O OUT TRICK (H) Trick HIGH 46 I/O OUT A M.
43 77 I/O OUT OSD DATA OSD Data 78 I/O OUT OSD STB OSD Strobe 79 I/O OUT OSD CLK OSD Clock 80 I/O OUT EP (H) EP HIGH 81 Vcc Vcc Vcc Vcc 82 V REF V REF V REF V REF 83 I/O OUT WARNING OUTPUT Warning out.
44 VOLTAGE CHART IC OP AMP (KA4558 IC502) IC RESET (MN1380L IC503) IC MOTOR DRIVE (BA6209 IC504) IC OP AMP (KA4558 IC505) IC MOTOR DRIVE (BA6209 IC504) REC PB REC PB 1 2.9 3.4 5 3.0 3.2 2 3.0 3.2 6 3.0 3.2 3 3.0 3.2 7 3.0 3.0 4 0.0 0.0 8 5.8 5.8 REC PB 1 0.
45 IC OP AMP (KA4558 IC901) IC RELAY (A9W-K RL901) IC RELAY (A9W-K RL902) 5 9.1 9.1 17 0.5 0.5 6 3.6 3.6 18 0.0 0.0 7 9.2 9.2 19 4.3 4.3 8 3.6 3.6 20 0.0 0.0 9 0.0 0.0 21 4.3 4.3 10 3.6 3.6 22 4.3 4.2 11 0.0 5.2 23 0.0 0.0 12 4.2 4.2 24 4.9 0.5 REC PB REC PB 1 9.
46 IC VIDEO (LA7391A IC301) IC CCD (LC89962 IC302) IC HEAD AMP (LA7374 IC401) REC PB REC PB 1 0.0 0.0 22 4.2 4.2 2 1.25 2.3 23 3.7 3.4 3 2.4 2.3 24 3.4 3.4 4 2.7 2.5 25 2.4 2.0 5 2.6 4.7 26 1.9 2.0 6 2.6 4.7 27 2.0 2.0 7 4.8 4.8 28 4.9 4.9 8 2.3 2.4 29 0.
47 IC VIDEO SW (LA7152 IC303) IC OSD (LA74763 IC001) 4 0.0 0.0 19 0.3 0.2 5 0.0 0.0 20 4.1 0.0 6 1.4 1.4 21 4.1 0.0 7 4.3 1.4 22 0.1 0.6 8 0.0 0.0 23 0.0 0.0 9 3.5 3.5 24 0.1 0.1 10 0.0 0.8 25 0.0 0.0 11 3.8 2.4 26 0.0 0.0 12 1.6 2.5 27 0.1 1.0 13 2.1 0.
48 IC VIDEO AMP (NJM2267 IC002) TRANSISTER 14 0.0 0.0 29 0.0 0.0 15 4.3 4.3 30 4.9 4.9 REC PB REC PB 1 2.2 2.2 5 1.5 1.5 2 0.0 0.0 6 1.6 1.6 3 2.4 2.4 7 4.9 4.9 4 2.5 2.5 8 1.9 1.9 REC PB E B C E B C Q201 0.1 0.5 4.7 0.0 0.5 0.5 Q202 0.0 0.0 0.0 0.0 0.
49 Q402 2.4 1.7 4.9 1.7 2.3 4.9 Q403 2.5 1.8 0.0 2.5 1.8 0.0 Q404 1.8 1.4 4.9 1.8 2.4 4.9 Q405 2.7 1.8 4.9 2.7 1.8 4.9 Q406 2.7 3.3 4.9 2.7 3.3 4.9 Q407 0.0 0.0 3.3 0.0 0.0 3.3 Q408 3.1 3.8 4.9 1.8 2.4 4.9 Q409 0.0 4.3 0.0 1.1 1.4 0.0 Q370 1.7 2.3 3.8 1.
50 1. CONNECTION DIAGRAM CIRCUIT DIAGRAM.
51 CIRCUIT DIAGRAM 2. POWER CIRCUIT DIAGRAM.
52 CIRCUIT DIAGRAM 3. SYSCON CIRCUIT DIAGRAM.
53 CIRCUIT DIAGRAM 4. VIDEO CIRCUIT DIAGRAM.
54 CIRCUIT DIAGRAM 5. HEADAMP CIRCUIT DIAGRAM.
55 CIRCUIT DIAGRAM 6. OSD CIRCUIT DIAGRAM.
56 CIRCUIT DIAGRAM 7. Y/C SEPARATION CIRCUIT DIAGRAM.
57 CIRCUIT DIAGRAM 8. AUDIO CIRCUIT DIAGRAM.
58 CIRCUIT DIAGRAM 9. LOGIC CIRCUIT DIAGRAM.
59 CIRCUIT DIAGRAM 10. TERMINAL CIRCUIT DIAGRAM.
60 COMPONENTS LOCATION GUIDE ON PCB BOTTOM VIEW 1. PCB MAIN.
61 COMPONENTS LOCATION GUIDE ON PCB BOTTOM VIEW 2. PCB UNION.
62 DISASSEMBLY 1. PANEL FRONT ASS ’ Y.
63 DISASSEMBLY 2. SET TOTAL ASS ’ Y.
64 DISASSEMBLY 3. PACKING ASS ’ Y.
65 ELECTRICAL PARTS LIST DEL : DV-K580NZ- T LOC PART-CODE PART-NAME PART-DESC 1 97PC0252A- ACCESSORY AS DV-K580NZ-T D001 97P9560000 MANUAL OWNERS ALL MODEL 2 97PC0022P- PACKING AS DV-K444DY-AQ C001 97P4923200 PAD LEFT/RIGHT EPS C002 97P4803100 POLY BAG FOR SET P .
66 A0400 97SA310900 S SLANT POLE AS G,FM,K-MECHA B0400 97SA409900 S POLE BASE AS G,FM,K-MECHA C0400 97S1402600 BASE S POLE ZDC-2 C0410 97S3513200 POLE SLANT SUS303 B0410 97SA411300 GUIDE ROLLER AS VW-32, LEE B0420 97S3102800 SCREW MACHINE PAN M2X0.
67 B2820 97S3003000 SPG T SUB BRAKE SUS304WPB D0.5 A2900 97SA309110 MAIN BRAKE AS K-MECHA B2900 97S2603010 LEVER S MAIN BRAKE KP213G30 NATURAL B2910 97S2603110 LEVER T MAIN BRAKE KP213G30 GREEN B2920 97S3003010 SPG MAIN BRAKE SUS304WPB D0.35 B2930 97S4102610 FELT MAIN BRAKE CLARINO 3611 8X4XT1.
68 S504A 97P2338200 HOLDER TR ABS T201 560202L697 COIL OSC DEO-010(BIAS) U001 97P65246MA PCB MAIN 330*247*1.6T(K580NZ-N) VA801 DSVC471D14 VARISTOR SVC471D14A X001 5XJ14R31AE CRYSTAL QUARTZ HC-49/S 14.31818MHZ 30PPM 2 X302 97P7005100 DELAY LINE 1H ADL-FN2038Y X303 5PUGL349KN FILTER COMB UGL-349KNT X501 5XJ16R0LAE CRYSTAL QUARTZ HC-49/S 16.
69 C437 HCLK681JCA C CHIP CERA 50V SL 680PF J 2012 C438 HCFK104ZCA C CHIP CERA 50V Y5V 0.1MF Z 2012 C439 HCFK103ZCA C CHIP CERA 50V Y5V 0.01MF Z 2012 C440 HCFK104ZCA C CHIP CERA 50V Y5V 0.1MF Z 2012 C441 HCFK104ZCA C CHIP CERA 50V Y5V 0.1MF Z 2012 C442 HCFK104ZCA C CHIP CERA 50V Y5V 0.
70 R205 HRFT562JCA R CHIP 1/10 5.6K OHM J 2012 R206 HRFT183JCA R CHIP 1/10 18K OHM J 2012 R207 HRFT220JCA R CHIP 1/10 22 OHM J 2012 R208 HRFT333JCA R CHIP 1/10 33K OHM J 2012 R209 HRFT151JCA R CHIP 1/10 150 OHM J 2012 R210 HRFT334JCA R CHIP 1/10 330K OHM J 2012 R211 HRFT822JCA R CHIP 1/10 8.
71 R413 HRFT223JCA R CHIP 1/10 22K OHM J 2012 R417 HRFT102JCA R CHIP 1/10 1K OHM J 2012 R418 HRFT561JCA R CHIP 1/10 560 OHM J 2012 R419 HRFT102JCA R CHIP 1/10 1K OHM J 2012 R420 HRFT821JCA R CHIP 1/10.
72 R908 HRFT103JCA R CHIP 1/10 10K OHM J 2012 R909 HRFT103JCA R CHIP 1/10 10K OHM J 2012 R910 HRFT103JCA R CHIP 1/10 10K OHM J 2012 R911 HRFT102JCA R CHIP 1/10 1K OHM J 2012 R912 HRFT103JCA R CHIP 1/1.
73 C355 CMXM2A223J C MYLAR 100V 0.022MF J TP C356 CEXF1H100A C ELECTRO 50V RSM 10MF (5X7) TP C376 CEXF1C470A C ELECTRO 16V RSM 47MF (5X7) TP C380 CEXF1C470A C ELECTRO 16V RSM 47MF (5X7) TP C391 CEXF1C470A C ELECTRO 16V RSM 47MF (5X7) TP C401 CEXF1C470A C ELECTRO 16V RSM 47MF (5X7) TP C403 CEXF1H479A C ELECTRO 50V RSM 4.
74 Q403 TZTA1266Y- TR KTA1266Y- (AUTO)(1015Y) Q404 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q405 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q406 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q407 TZSR1004-- TR KSR100.
75 2 D918 DZUZ9R1BSC DIODE ZENER UZ-9.1BSC(8.89-9.29V) D919 DZUZ5R6BSB DIODE ZENER UZ-5.6BSC D920 DZUZ5R6BSB DIODE ZENER UZ-5.6BSC JP001~ JP098 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING JP100~ JP194 85801065GY WIRE COPPER AWG22 1/0.65 TIN COATING JP196~ JP238 85801065GY WIRE COPPER AWG22 1/0.
76 R575 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R576 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R577 RD-AZ102J- R CARBON FILM 1/6 1K OHM J R578 RD-4Z102J- R CARBON FILM 1/4 1K OHM J R579 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R594 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R599 RD-AZ513J- R CARBON FILM 1/6 51K OHM J R735 RD-AZ472J- R CARBON FILM 1/6 4.
77 R727 RD-AZ473J- R CARBON FILM 1/6 47K OHM J R728 RD-AZ473J- R CARBON FILM 1/6 47K OHM J R729 RD-AZ473J- R CARBON FILM 1/6 47K OHM J R730 RD-AZ473J- R CARBON FILM 1/6 47K OHM J R731 RD-AZ103J- R CAR.
78 C51 CMXL2G333K C MYLAR 400V MEU 0.033MF K C62 CEXF1C681F C ELECTRO 16V RX 680MF 10X20 C64 CEXF1A102F C ELECTRO 10V RX 1000MF 10X20 C65 CEXF1H220F C ELECTRO 50V RX 22MF 6.
DAEWOO ELECTRONICS CO., LTD 686, AHYEON-DONG MAPO-GU SEOUL, KOREA C.P.O. BOX 8003 SEOUL, KOREA TELEX : DWELEC K28177-8 CABLE : "DAEWOOELEC" E-mail : G7F00E@web.
Een belangrijk punt na aankoop van elk apparaat Daewoo DV-K580NZ-T (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Daewoo DV-K580NZ-T heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Daewoo DV-K580NZ-T vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Daewoo DV-K580NZ-T leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Daewoo DV-K580NZ-T krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Daewoo DV-K580NZ-T bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Daewoo DV-K580NZ-T kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Daewoo DV-K580NZ-T . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
