Gebruiksaanwijzing /service van het product SC6000 van de fabrikant Datalogic Scanning
Ga naar pagina of 60
SC6000 Reference Manual.
.
SC6000 REFERENCE MANUAL.
DATALOGIC S.p.A. Via Candini 2 40012 - Lippo di Calderara di Reno Bologna - Italy SC6000 Reference Manual Ed.: 10/2005 ALL RIGHTS RESERVED Datalogic reserves the right to make modifications or improvements wi thout prior notification.
CONTENTS REFERENCES ............................................................................................................. v Reference Documentation ............................................................................................ v Services and Support .
Main Interface ............................................................................................................. 39 Extended I/O ..............................................................................................................
REFERENCES REFERENCE DOCUMENTATION The documentation related to the SC6000 is listed below: • PWO power supply unit • Document about the Ethernet connectivity • Document about the Profibus conne.
SAFETY REGULATIONS POWER SUPPLY - This product is intended to be installed by Qualified Personnel only. WEEE COMPLIANCE vi.
GENERAL VIEW SC6000 Controller 2 4 5 6 1 3 Figure 1 - General View Connector Panel Power On and Communication LEDs Connector Panel Leg e nd 1 3 2 LCD Display Progr amming Keypad Status LEDs 4 6 5 vii.
4 2 3 1 6 5 Figure 2 - SC6000-1200 Standard Model Connector Panel M odem Con nector 1 Power /Net Conn ect or 2 M ain Interf ace Con nector 3 Ethernet Connector 4 Auxi liary Interf ace C onnector 5 Ext.
GUIDE TO INSTALLATION The following can be used as a checklist to verify all the steps necessary to complete installation of the SC6000 Controller. 1) Read all information in the section “Safety Precautions” at the beginning of this manual. 2) Correctly mount the SC6000 using the bracket provided according to the information in par.
x.
INTRODUCTION 1 1 INTRODUCTION 1.1 PRODUCT DESCRIPTION The new SC6000 Controller offers all the necessary functions to make the phases of installation, setup, testing, and maintenance of the omni-directional reading tunnel easy and quick.
SC6000 1 1.3 LED INDICATORS 2 1 Figure 6 - LEDs Description Power ON and Com m uni cation LEDs 1 Status LEDs 2 System Signal LEDs Name Color State Function Pow er ON Green ON OFF SC6000 Powered No Pow.
INTRODUCTION 1 1.4 ACCESSORIES The following accessories are necessary to build a reading station based on SC6000 (the scanner-related accessories are not included): Name Description Part Number CAB-S.
SC6000 2 2 INSTALLATION To install the system follow the given procedure: 1) Select the mounting location and mount the SC6000 Controller; 2) Mount the PWO (refer to the PWO Installation Manual); 3) Proceed with system electrical connections; 4) Install the GENIUS™ program on the configuration PC.
INSTALLATION 2 2.2 OVERALL DIMENSIONS 319.5 [12.58] 248.7 [9.79] 80.2 [3.16] 99.7 [3.93] 124.4 [4.90] 39.7 [1.56] MØ8 39.7 [1.56] 124.4 [4.90] 298 [11.73] mm inch Figure 8 - SC6000 Overall Dimensions 180 [7.09] 309 [12.17] 5 [0.20] N ° 2 R 1 5 [ R 0 .
SC6000 2 2.3 MECHANICAL MOUNTING To mount the SC6000 Controller on the reading station frame proceed as follows: 1 Mount the bracket on the reading station frame: the slots on the bracket will help obtain the best positioning.
INSTALLATION 2 The specially punched steel ring has been designed to obtain the most precise rotation possible in terms of angle calibration, steadiness and consequent absence of torque between both sides of device. 5 Place a locking washer and then a flat washer onto each knob.
SC6000 2 2.4 ELECTRICAL CONNECTIONS The connectors available for each scanner model are the following: Scanner Model Connector Type Power/Net 25-pin male power supply, lonworks and input/output signal.
INSTALLATION 2 2.4.2 Ethernet Connector This connector is available for all SC6000 Controller models and allows the Ethernet connection to the host. In the SC6000-1230 Dual Ethernet there are two Ethernet connectors for secondary host connections.
SC6000 2 Ethernet Interface The Ethernet interface (NIC) can be used for TCP/IP communication with a remote or local host computer by connecting the SC6000 Controller to a LAN or directly to a host PC.
INSTALLATION 2 2.4.3 DeviceNet Connector The 5-pin male connector is only available in the SC6000-1215 DeviceNet model and allows connection between the host and the controller: 1 3 2 4 5 Figure 19 - .
SC6000 2 2.4.4 Profibus Connector The 9-pin female Profibus connector (white) is only available in the SC6000-1211 Profibus model and allows connection between the host and the controller: 5 1 9 6 Figure 20 - Profibus 9-pin Fema le Connector 9-pin D-sub Female Profibus connector pinout Pin Name Function 1 Shield* Shield, protective ground resp.
INSTALLATION 2 2.5 TYPICAL LAYOUTS The following typical layouts refer to system har dware configurations, but also require the correct setup of the software configuration parameters (see par. 3.2 for details). Other layouts require the use of a specific SC6000 Controller model.
SC6000 2 Figure 23 - Modem Connection 2.5.2 Fieldbus Network The SC6000 can be connected to a Fieldbus network (Ethernet, Profibus and DeviceNet) to communicate with a remote host (for example, remote PC connected via Internet). Connections are made directly through cables to the Fieldbus connector and do not require any converter or adapter.
INSTALLATION 2 Figure 25 - Dual Ethernet Conne ction 2.6 KEYPAD AND DISPLAY The SC6000 keypad allows entering a menu to select one of the functions described in the following paragraphs. 2.6.1 Standard Mode Upon startup, the diagnostic mask window is visualized by default.
SC6000 2 Reading Performance Window This window displays the following data: • Number of the processed parcels • Good Read Rate • No Read Rate • Multiple Read Rate Reading Mask Window This window indicates the node that performed a reading of the codes enabled on the master.
SOFTWARE CONFIGURATION 3 3 SOFTWARE CONFIGURATION 3.1 GENIUS™ INSTALLATION Genius ™ is a new Datalogic scanner configuration tool providing several important advantages: • Multi-language version.
SC6000 3 2. From the Device Menu select Local Device Network Settings and configure your SC6000 as Master (SYNCHRONIZED is the default value), as shown in the figure below: Figure 27 – Local Device Netw ork Settings The following dialog box appears asking whether to send the configuration to the Master or not: 3.
SOFTWARE CONFIGURATION 3 Each device is indicated by the following graphical objects: • check box allowing to select/deselect a specific device to perform the desired operations (i.
SC6000 3 Proceed with the network setup by using one of the icons available on the Tool Bar according to the procedure to follow: = Net-Autoset procedure = Network Wizard procedure = Express Network S.
SOFTWARE CONFIGURATION 3 Network Wizard Before performing this procedure, a Lonworks address must be assigned to each slave scanner. The most practical method is through the Net-Autoset procedure. See par. 3.2.2 for alternative address assignment methods.
SC6000 3 2. If desired, select a slave scanner within the "Current Devices" area and click on the icon (or select the "Show Device" option from the right-click menu) to make the di.
SOFTWARE CONFIGURATION 3 3.2.2 Alternative Slave Address Assignment As alternatives to Network Setup through the Master, each Slave scanner can be assigned an address through the following methods: • random address assignment from SC6000 to all slaves in the network by performing the CASP™ procedure as described in par.
SC6000 3 4) From the Device Menu select Local Device Network Settings and configure your SC6000 as Other , as shown in the figure below: Figure 30 – Local Device Netw ork Settings 5) From the Readin.
SOFTWARE CONFIGURATION 3 6) Configure the Common Slave Scanner paramet ers according to your application using the Lonworks Slave Common Parameters branc h in the Reading System Layout folder.
SC6000 3 • Selecting the codes to be read in the Code Definition folder ( they must be the same as those set for the slave scanners ) • Set-up the communication and data formatting parameters in the Data Communications settings folder 8) Send the configuration to the Slave Scanners from the Send command in the Device Menu.
SOFTWARE CONFIGURATION 3 3.4 PARAMETER DEFAULT VALUES The following table contains the list of the factory default settings for the SC6000 Controller. Genius™ also allows checking the parameter defa.
SC6000 3 Parameter Default Setting Operating Modes Operating Mode Selection Packtrack Physical Encoder Enabled Encoder Step (hundredths of millimeter) 100 PS Line (mm) 0 Presence Sensor Input PS Prese.
SOFTWARE CONFIGURATION 3 Parameter Default Setting Auxiliary Serial Port Data TX Enabled (checked) Pass Through Disabled (checked) Parameters Baud Rate 115200 Parity None Data Bits 8 Stop Bits 1 Ethernet Port Status Enabled (checked) Eth_speed Auto DHCP Disabled IP_address 172.
SC6000 3 Parameter Default Setting Output 3 Line State Normally Open Activation Event None Alternative Activation Event None Deactivation Event None Alternative Deactivation Event None Output 4 Line S.
MAINTENANCE 4 4 MAINTENANCE 4.1 DATALOGIC AUTOMATIC REPLACEMENT PROCEDURE (DARP TM ) Once the system configuration has been completed, launch the DARP™ backup by one of the following methods: Using Genius: Click on the DARP™ backup icon in the Device Network area.
SC6000 4 In case of SC6000 failure proceed as follows: Figure 33 - Removing the Compact F lash 1. Disconnect the device 2. Remove the rubber cover of the Compact Flash slot using a screwdriver 3. Remove the Compact Flash 4. Connect a new SC6000 to the system 5.
TROUBLESHOOTING 5 5 TROUBLESHOOTING NOTE Before contacting your local Datalogic office or Datalogic Partner or ARC, it is suggested to save the device configuration to a *.ddc file by means of the Genius™ software configuration program and check the exact device model and serial number.
SC6000 5 TROUBLESHOOTING GUIDE Problem Suggestion Communication (Ethernet): the Ethernet LED is not lit. • Verify the HUB connection. • Verify Genius™ settings (see par. 3.4). Communication: data do not appear on the terminal. • In the Genius™ program enable the DATA COMMUNICATION SETTINGS/MAIN- AUXILIARY PORTDATA TX parameter.
TECHNICAL FEATURES 6 6 TECHNICAL FEATURES ELECTRICAL FEATURES Supply voltage 15 to 30 Vdc Power consumption 6.5 W typical 9 W Max. (including startup current) Main (isolated) Modem RS232 RS232 RS485 f.
SC6000 A A ALTERNATIVE CONNECTIONS REFERENCE POWER SUPPLY - I/O (POWER/NET CONNECTOR) The PWO supplies 24 VDC. 25-pin D-Sub Female Connector Pinout Pin Name Function 1 RE L1 Relay output control 2 REL3 Rel a y out p ut control 3 GND Ground 4 GND Ground 5 ENCODER A Encoder ( Tach ) 6 PS _ AUX A Presence sensor aux.
ALTERNATIVE CONNECTIONS REFERENCE A Lonworks SC6000 24 25 23 LON_IN A LON_ IN B SHIELD_I N 13 24 25 23 LON A LON B SHIELD LON_ OUT A LON_OUT B SHIELD_OUT 12 11 13 12 11 LON A LON B SHIELD USER IN TER .
SC6000 A V PS/PS A UX EN CO DER Gro und SC6000 A/B B/ A GND V S_INPUTS* Signal PWO V S V S PSIN + 5V ~ ~ + - *VS_IN PUTS is connected through the 25-pin E xtended I/O connector. If this connector is not used, VS_INPUTS mus t be wired from one of the scanner term inals insi de PWO, see the PWO Reference Manual for detail s.
ALTERNATIVE CONNECTIONS REFERENCE A MAIN INTERFACE The main serial interface is compatible with the following electrical standards: RS232 RS485 full-duplex RS485 half-duplex CAUTION Do not connect GND and GND_ISO to different (external) ground references.
SC6000 A SC6000 8 RTS RTS PWO GND-ISO 5 CTS 7 RX 3 RX TX 2 TX Shi eld Host Signal Gr ound CTS Figure 40 - RS232 Connections RS485 Full-Duplex Interface The RS485 full-duplex interface is used for non-.
ALTERNATIVE CONNECTIONS REFERENCE A EXTENDED I/O 25-pin D-Sub Male Connector Pinout Pin Name Function 1 VS_OUTPUTS Power for outputs 2 IN1 A Input signal 1 - polarity insensitive 3 IN2 A Input signal .
SC6000 A V USER I NTERFACE Ground SC6000 A/B B/ A GND V S_INPUT S Signal PW O Figure 44 - PNP Command Input Using Sys tem Power V USER I NTERFA CE Gro und SC6000 A/B B/ A GND V S_INPUT S Signal PWO Fi.
ALTERNATIVE CONNECTIONS REFERENCE A By default, OUT1 is associated with COMPLETE READ event, which activates when the code has been read correctly. In case the reader has been programmed to read several codes within the same reading phase, the event activates when all codes have been read.
SC6000 A MODEM SC6000 offers a dedicated 9-pin port for a Modem connection. The modem connection allows a Host to remotely control the reading station.
GLOSSARY Barcode A pattern of variable-width bars and spaces which represents numeric or alphanumeric data in machine-readable form. The general format of a barcode symbol consists of a leading margin, start character, data or message character, check character (if any), stop character, and trailing margin.
Scanner A device that examines a printed pattern (barcode) and either passes the uninterpreted data to a decoder or decodes the data and passes it onto the Host system. Serial Port An I/O port used to connect a scanner to your computer, identifiable by a 9-pin or 25-pin connector.
INDEX A Accessories; 3 C Connector Pinouts; 36 Connectors DeviceNet; 11 Ethernet; 9 Profibus; 12 D DARP TM ; 31 DeviceNet; 11 E Electrical Connections; 8 G General View; vii Genius™ Installation; 17.
DATALOGIC S.p.A., DATALOGIC S.p.A., 05 Via Candini, 2 Via Candini, 2 40012 - Lippo di Calderara 40012 - Lippo di Calderara Bologna - Italy Bologna - Italy dichiara che dichiara che declares that the d.
Een belangrijk punt na aankoop van elk apparaat Datalogic Scanning SC6000 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Datalogic Scanning SC6000 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Datalogic Scanning SC6000 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Datalogic Scanning SC6000 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Datalogic Scanning SC6000 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Datalogic Scanning SC6000 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Datalogic Scanning SC6000 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Datalogic Scanning SC6000 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
