Gebruiksaanwijzing /service van het product 8126VSS van de fabrikant DAVIS
Ga naar pagina of 16
VSS Installation Guide Product # 8126VSS.
© Davis Instruments Corp. 200 7. All rights reserved. Product Number: 8126VSS Part Number: 7395.062 DriveRight VSS Installation Guide Rev . G (9/13/07) This product complies with the essential pro- tection requirement s of the EC EMC Directive 89/336/EC.
1 Introduction This manual provides instructions and information necessary to install the VSS version of the DriveRight 600 E device. Since the specific installation details va ry from vehicle to vehicle, these instructions are intended to be a general guide for professio nal installers or for knowledgeable and experienced mechanics.
2 Harness and Adapter Cables Wirin g Additional Document ation Refer to the following documents fo r information on configuring and using your DriveRigh t: • The DriveRight 600 E User ’ s Guide included with your unit. • The Online Hel p System in the DriveRigh t software.
3 Installations using Adapter Cable Dig ital Inputs If you are using the adapter cable digital inpu ts in your installation, the following additional tools and ot her items may also be required: • Crimping T ool • Multimeter • Fuse T ap - Required to obtain +12 V from the fuse panel.
4 • Decide where to install the harn ess cable and wher e to connect the power and ground leads — Find a location inside the vehicle where you can bring together the harness cable leads, the VSS, power and ground tap wires and th e adapter cable leads.
5 Procedure 1: Install the Harness Cable CAUTION: Always use safety stands when working under a raised vehicle. Never work under a vehicle supported only by a jack. Note: Make sure the harness cable and adapter cable can re ach the DriveRight con- sole mounting location before making the following connections.
6 related equipment (headlights, tail lights, air bag, etc.) that you can tap into with an in-line splice. Possible candidate wires include those from the cigarette lighter , dome light, glove compartment light, clock, tail gate light, or other convenience functio ns.
7 Procedure 2: Install the Adapter Cable T wo digital inputs lo cated on the ad apter cable are available to monitor the on/off state of lights, including brake lights, or of other 12 VDC electrical accessories. T ypically Digi tal Input 1 monitors the brake lights and Digital Input 2 monito rs the headlights.
8 two connectors together . The two cab les will lock together when properly connected. Note: T o disconnect the cables, hold both cables by the housing and pull apart. Sliding the housing on the adapter cable connector will re lease the lock and allow the cables to be separated.
9 Instructions for Using V elcro ® 1. Apply the two adhesive-backed V elcro loop tapes to the flat spaces on the back of the console or to the back of the bracket. 2. Attach the hook tapes to t he loop tapes, then press adhesive b acking of the hook tape onto your selected mounti ng surface.
10 3. Once plugged in, the console should display the Current Reading s screen. If the display remains b lank, check if the battery is properly installed in the unit. If it is, press MODE. If it remains blank, check the adapter cable and harness cable connections.
11 T ro ubleshooting section on page 12 in this manual as wel l as the troubleshooting info rmation in the DriveRight 600 E User ’ s Guide for help. VSS DIP Switch Flow Chart Use this flow chart to determine the optimum VSS dip switch setting. 0 = OFF 1 = ON Set 1 2 3 4 0 1 0 1 Drive 2 mph.
12 T roubleshooting If your speed is no t registering co rrectly , consult the following check list to help you identify the cau se of the problem. • Make sure the display is reading in the unit s (km/hr or mph) you expect. • Hold down the Set/Clr button in the Curren t Screen to change the units.
13 Specifications V isit our website for additional product in formation: www .davis- net.com. VSS Comp atibility The DriveRight can work with many different VSS signals provided the switch settings of the VSS in-lin e circuit are set correctly . However , if the signal does not meet the specifications below it m ay not work.
14 T echnical Support If you are experiencing problems w ith your Dri veRight, first check t he cable connections and veri fy the calibration sett ings. If you are unable to solve the problem, please call Da vis T echnical Support. W e’ll be glad to help.
Een belangrijk punt na aankoop van elk apparaat DAVIS 8126VSS (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen DAVIS 8126VSS heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens DAVIS 8126VSS vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding DAVIS 8126VSS leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over DAVIS 8126VSS krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van DAVIS 8126VSS bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de DAVIS 8126VSS kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met DAVIS 8126VSS . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
