Gebruiksaanwijzing /service van het product I14RMT7500SLV van de fabrikant Dell
Ga naar pagina of 79
Dell Latitude E5430 Owner's Manual Regulatory Model: P27G Regulatory Type: P27G001.
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Contents 1 Working on Your Computer ................................................................................... 7 Before Working Inside Your Computer .............................................................................................
Installing the Thermal Module ............................................................................................................ 30 Removing the Processor ......................................................................................
Entering System Setup ........................................................................................................................ 67 System Setup Options ....................................................................................
6.
1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety.
3. If the computer is connected to a docking device (docked) such as the optional Media Base or Battery Slice, undock it. CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device.
Turning Off Your Computer CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer. 1. Shut down the operating system: – In Windows 8: * Using a touch-enabled device: a. Swipe in from the right edge of the screen, opening the Charms menu and select Settings .
5. Turn on your computer. 10.
2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Recommended Tools The procedures in this document may req.
Installing the ExpressCard 1. Slide the ExpressCard in its slot until it clicks in place. 2. Follow the procedures in After Working Inside Your Computer . Removing the Battery 1. Follow the procedures in Before Working Inside Your Computer . 2. Slide the battery release latches into the unlock position.
Installing the Battery 1. Slide the battery into its slot until it clicks into place. 2. Follow the procedures in After Working Inside Your Computer . Removing the Access Panel 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove the battery.
Installing the Access Panel 1. Slide the base cover into its slot until it clicks into place. 2. Install the screws that secure the access panelto the computer. 3. Install the battery. 4. Follow the procedures in After Working Inside Your Computer . Removing the SIM Card 1.
3. Perform the following steps: a) Pry up the bottom edge of the display bezel. b) Work your way around the sides and top edge of the display bezel. 4. Remove the display bezel from the computer. Installing the Display Bezel 1. Place the display bezel onto the display assembly.
Installing the Camera 1. Place the camera and microphone module on its place. 2. Connect the camera cable. 3. Tighten the screw to secure the camera and microphone module. 4. Install: a) display bezel b) battery 5. Follow the procedures in After Working Inside Your Computer .
4. Flip the display panel over. 5. Lift the mylar tape and disconnect the low-voltage differential signalling (LVDS) cable from the back of the display panel.
Installing the Display Panel 1. Place the display panel to the display assembly. 2. Align the display panel in its original position. 3. Connect the low-voltage differential signaling (LVDS) cable to the display panel and attach the tape. 4. Flip the display panel over and tighten the screws to secure the display panel.
4. Pry up the keyboard trim starting from the bottom edge. 5. Work your way around the sides and the top edge of the keyboard trim. 6. Lift upwards and remove the keyboard trim from the computer.
Installing the Keyboard Trim 1. Align the keyboard trim to its place. 2. Press along the sides of the keyboard trim until it snaps in place. 3. Install the battery. 4. Follow the procedures in After Working Inside Your Computer . Removing the Keyboard 1.
3. Remove the screws at the back of the computer. 4. Remove the screws that secure the keyboard in place. 5. Lift the clip to release the keyboard cable and disconnect it from the computer .
6. Flip the keyboard over. 7. Peel off the adhesive tape securing the keyboard flat flex cable to the back of the keyboard and remove it from the computer. 8. Remove the keyboard from the computer . Installing the Keyboard 1. Attach the keyboard flat flex cable to the keyboard.
8. Install: a) keyboard trim b) battery 9. Follow the procedures in After Working Inside Your Computer . Removing the Optical Drive 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a) battery b) access panel 3. Remove the screw that secures the optical drive.
5. Remove the optical drive from the computer. 6. Remove the screws that secure the optical drive bracket. 7. Remove the optical drive bracket. 8. Disengage the optical drive bezel tabs to separate the optical drive bezel from the optical drive. 9. Remove the optical drive bezel.
Removing the Hard Drive 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a) battery b) access panel 3. Remove the screws that secure the hard drive bracket in place. 4. Use the tab to pull the hard drive bracket to release the hard drive from its connector.
5. Remove the hard drive from the computer. 6. Remove the screws that secure the hard drive bracket. 7. Remove the hard drive bracket from the hard drive. Installing the Hard Drive 1. Engage the hard drive bracket to the hard drive. 2. Tighten the screws that secure the hard drive bracket.
Removing the WLAN Card 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a) battery b) base cover 3. Perform the following steps: a) Disconnect the antennae cables from the WLAN card. b) Remove the screw that secures the WLAN card to the computer.
Installing the Memory Module 1. Insert the memory into the memory socket. 2. Press the clips to secure the memory module to the system board. 3. Install: a) base cover b) battery 4. Follow the procedures in After Working Inside Your Computer . Removing the Right Base Panel 1.
Installing the Right Base Panel 1. Place the right base panel on the computer. 2. Tighten the screws that secure right base panel to the computer. 3. Install: a) access panel b) battery 4. Follow the procedures in After Working Inside Your Computer . Removing the Thermal Module 1.
Installing the Thermal Module 1. Place the thermal module in its compartment. 2. Tighten the screws that secures the thermal module to the computer. 3. Install: a) right base panel b) access panel c) battery d) SD memory card 4. Follow the procedures in After Working Inside Your Computer .
Removing the Palmrest 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a) SD memory card b) battery c) access panel d) keyboard trim e) keyboard f) optical drive g) right base panel 3. Remove the screws at the bottom of the computer.
5. Disconnect the LED board flat flex cable. 6. Disconnect the media button flat flex cable. 7. Disconnect the touch pad flat flex cable. 8. Disconnect the fingerprint scanner flat flex cable. 9. Disconnect the power button flat flex cable. 10. Lift up the right edge of palmrest assembly.
Installing the Palmrest 1. Align the palm rest assembly to its original position in the computer and snap it into place. 2. Connect the following cables to the system board: a) power button flat flex cable. b) fingerprint scanner flat flex cable c) touch pad flat flex cable d) media button flat flex cable e) LED board flat flex cable 3.
Installing the ExpressCard Reader Cage 1. Align the ExpressCard reader cage to its original position in the computer and snap it into place. 2. Install the screws that secure the ExpressCard reader cage. 3. Install: a) palmrest b) right base panel c) optical drive d) keyboard e) keyboard trim f) access panel g) battery h) SD memory card 4.
3. Install the screw that secures the bluetooth module to the computer. 4. Connect the bluetooth cable to the system board. 5. Install: a) palmrest b) right base panel c) optical drive d) keyboard e) keyboard trim f) access panel g) battery h) SD memory card 6.
4. Install: a) bluetooth module b) palmrest c) right base panel d) optical drive e) keyboard f) keyboard trim g) access panel h) battery i) ExpressCard j) SD memory card 5. Follow the procedures in After Working Inside Your Computer . Removing the Display Assembly 1.
4. Disconnect the low-voltage differential signaling (LVDS) cable. 5. Pull the antennas through the opening to the top of the computer. 37.
6. Remove the screws that secure the display assembly in place. 7. Remove the display assembly from the computer. Installing the Display Assembly 1. Install the screws that secures the display assembly in place. 2. Insert the low-voltage differential signaling (LVDS) cable and wireless antennae cables through the holes on the chassis.
Removing the Right Support Frame 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a) SD memory card b) ExpressCard c) battery d) access panel e) keyboard trim f) keyboard g) optical drive h) hard drive i) WLAN card j) right base panel k) thermal module l) palmrest m) display assembly 3.
5. Lift the right support frame away from the computer. Installing the Right Support Frame 1. Place the right support frame on the computer. 2. Tighten the screws to secure the right support frame to the computer. 3. Connect the flat flex cable located at the base of the right support frame.
Removing the Modem Card 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a) SD memory card b) ExpressCard c) battery d) access panel e) keyboard trim f) keyboard g) optical drive h) hard drive i) right base panel j) thermal module k) palmrest l) ExpressCard reader cage m) display assembly n) right support frame 3.
5. Install: a) right support frame b) display assembly c) ExpressCard reader cage d) palmrest e) thermal module f) right base panel g) hard drive h) optical drive i) keyboard j) keyboard trim k) access panel l) battery m) ExpressCard n) SD memory card 6.
4. Lift the left support frame away from the computer. Installing the Left Support Frame 1. Place the left support frame on the computer. 2. Tighten the screws to secure the left support frame to the computer.
Removing the System Board 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a) battery b) access panel c) keyboard trim d) keyboard e) optical drive f) hard drive g) WLAN card h) right base panel i) thermal module j) palmrest k) ExpressCard reader cage l) display assembly m) left support frame 3.
7. Disconnect the bluetooth cable. 8. Remove the screws that secure the system board. 45.
9. Lift the right edge of the system board assembly and raise it to a 45–degree angle. 10. Release the system board from the port connectors on the left and remove the system board. Installing the System Board 1. Align the system board into its original position on the computer.
4. Install: a) left support frame b) display assembly c) ExpressCard reader cage d) palmrest e) thermal module f) right base panel g) hard drive h) optical drive i) keyboard j) keyboard trim k) access panel l) battery m) SD memory card 5. Follow the procedures in After Working Inside Your Computer .
Installing the Coin-Cell Battery 1. Place the coin-cell battery on the system board with adhesive side downwards. 2. Connect the coin-cell battery cable to the system board.
4. Lift the Input/Output (IO) board out of the computer. Installing the Input/Output (I/O) Board 1. Place the Input/Output (I/O) board in the computer.
Removing the Power Connector 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a) SD memory card b) ExpressCard c) battery d) access panel e) keyboard trim f) keyboard g) op.
4. Remove the power connector. Installing the Power Connector 1. Install the power connector in the computer. 2. Thread the power connector in the routing channel.
Removing the System Fan 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a) SD memory card b) ExpressCard c) battery d) access panel e) keyboard trim f) keyboard g) optical.
4. Lift the system fan out of the computer. Installing the System Fan 1. Place the system fan in the computer. 2. Tighten the screws to secure the fan in the computer.
Removing the Network Connector 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a) SD memory card b) ExpressCard c) battery d) access panel e) keyboard trim f) keyboard g) .
3. Install: a) system board b) modem card c) left support frame d) right support frame e) display assembly f) ExpressCard reader cage g) palmrest h) thermal module i) right base panel j) WLAN card k) hard drive l) optical drive m) keyboard n) keyboard trim o) access panel p) battery q) ExpressCard r) SD memory card 4.
3. Remove the screws to release the speakers. 4. Remove the speaker cables from the routing channels. 5. Lift the speaker out from the computer. Installing the Speakers 1. Place the speakers in the computer. 2. Tighten the screws to secure the speakers to the computer.
4. Install: a) system board b) left support frame c) display assembly d) audio board e) bluetooth module f) ExpressCard reader cage g) palmrest h) thermal module i) right base panel j) WLAN card k) hard drive l) optical drive m) keyboard n) keyboard trim o) access panel p) battery q) ExpressCard r) SD memory card 5.
58.
3 Specifications Specifications NOTE: Offerings may vary by region. For more information regarding the configuration of your computer, click Start (Start icon) → Help and Support , and then select the option to view information about your computer. Table 1.
Table 4. Audio Feature Specification Type four-channel high definition audio Controller IDT92HD93 Stereo conversion 24-bit (analog-to-digital and digital-to-analog) Interface: Internal high definition.
Feature Specification Subscriber Identity Module (SIM) port one Table 8. Display Feature Specification Type Latitude E5430 • HD(1366x768), WLED • HD+(1600 x 900) Latitude E5530 • HD(1366x768), WLED • FHD (1920 x 1080) Size Latitude E5430 14.0" Latitude E5530 15.
Feature Specification Horizontal • +/- 40° for HD • +/- 60° for FHD Vertical • +10°/-30° for HD • +/-50° for FHD Pixel pitch: Latitude E5430 0.2265 mm x 0.2265 mm Latitude E5530 • 0.2520 mm x 0.2520 mm for HD • 0.1790 x 0.1790 for FHD Table 9.
Feature Specification 4-cell 240.00 g (0.53 lb) 6-cell 344.73 g (0.76 lb) 9-cell 508.20 g (1.12 lb) Voltage 4-cell 14.8 VDC 6- and 9-cell 11.1 VDC Temperature range: Operating 0 °C to 50 °C (32 °F .
Physical Latitude E5430 Latitude E5530 Depth 240.00 mm (9.44 inches) 251.00 mm (9.88 inches) Weight 2.04 kg (4.50 lb) 2.38 kg (5.25 lb) Table 14. Environmental Feature Specification Temperature: Opera.
4 Additional Information This section provides information for the additional features that are part of your computer. Docking Port Information The docking port is used for connecting the laptop to a docking station (optional). 1. Subscriber Identity Module (SIM) Port 2.
66.
5 System Setup Overview System Setup allows you to: • change the system configuration information after you add, change, or remove any hardware in your computer. • set or change a user-selectable option such as the user password. • read the current amount of memory or set the type of hard drive installed.
Option Description • Device Information: Displays Primary Hard Drive, Fixed bay Device, System eSATA Device, Dock eSATA Device, LOM MAC Address, Video Controller, Video BIOS Version, Video Memory, Panel Type, Native Resolution, Audio Controller, Modem Controller, Wi-Fi Device, Cellular Device, Bluetooth Device.
Option Description Serial Port Allows you to configure the integrated serial port. The options are: • Disabled • COM1: This option is enabled by default. • COM2 • COM3 • COM4 SATA Operation Allows you to configure the internal SATA hard-drive controller.
Option Description • Level is 50% • Level is 75% • Level is 100% Miscellaneous Devices Allows you to enable or disable the following devices: • Enable Internal Modem • Enable Microphone • .
Option Description NOTE: If Strong Password is enabled, Admin and System passwords must contain at least one uppercase character, one lowercase character and be at least 8 characters long. Password Configuration Allows you to determine the minimum and maximum length of Administrator and System passwords.
Table 19. Performance Option Description Multi Core Support This field specifies whether the process will have one or all cores enabled. The performance of some applications will improve with the additional cores. This option is enabled by default.Allows you to enable or disable multi-core support for the processor.
Option Description Wireless Radio Control Allows you to enable or disable the feature that automatically switches from wired or wireless networks without depending on the physical connection.
Option Description • By Numlock Mouse/Touchpad Allows you to define how the system handles mouse and touch pad input. The options are: • Serial Mouse • PS2 Mouse • Toushpad/PS-2 Mouse: This option is enabled by default. Numlock Enable Allows you to enable the Numlock option when the computer boots.
Option Description • WWAN • WLAN • Bluetooth All the options are enabled by default. Table 24. Maintenance Option Description Service Tag Displays the Service Tag of your computer. Asset Tag Allows you to create a system asset tag if an asset tag is not already set.
76.
6 Diagnostics If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for technical assistance. The purpose of running diagnostics is to test your computer's hardware without requiring additional equipment or risking data loss.
Table 28. Keyboard Status Lights Turns on when the numeric keypad is enabled. Turns on when the Caps Lock function is enabled. Turns on when the Scroll Lock function is enabled.
7 Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options.
Een belangrijk punt na aankoop van elk apparaat Dell I14RMT7500SLV (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Dell I14RMT7500SLV heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Dell I14RMT7500SLV vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Dell I14RMT7500SLV leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Dell I14RMT7500SLV krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Dell I14RMT7500SLV bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Dell I14RMT7500SLV kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Dell I14RMT7500SLV . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
