Gebruiksaanwijzing /service van het product P52G van de fabrikant Dell
Ga naar pagina of 45
Dell Vostro 14 – 3449 Owner's Manual Regulatory Model: P52G Regulatory Type: P52G001.
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Contents 1 Working on Your Computer................................................................................ 5 Before Working Inside Your Computer ................................................................................................ 5 Recommended Tools .
Removing the Power Connector ....................................................................................................... 29 Installing the Power Connector ....................................................................................
1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety.
3. If the computer is connected to a docking device (docked), undock it. CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device. 4. Disconnect all network cables from the computer.
b. Click the and select Shut down . • In Windows 7: 1. Click Start . 2. Click Shut Down. or 1. Click Start . 2. Click the arrow in the lower-right corner of the Start menu as shown below, and then click Shut Down. . 2. Ensure that the computer and all attached devices are turned off.
2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. System Overview Figure 1.
Figure 2. Back View 1. battery 2. access panel 3. optical-disk drive Figure 3. Inside View – Back 1. memory module 2. WLAN card 3. hard drive 9.
Figure 4. System Board View 1. I/O board 2. speakers 3. coin-cell battery 4. system board 5. system fan 6. power connector Removing the Battery 1. Follow the procedures in Before Working Inside Your Computer . 2. Slide the release latches outwards to unlock the battery and lift the battery to remove it from the computer.
Installing the Battery 1. Insert the battery into the battery slot and press to lock in place. 2. Follow the procedures in After Working Inside Your computer . Removing the Optical-Disk Drive 1. Follow the procedures in Before Working Inside Your Computer .
Installing the Access Panel 1. Insert the access panel into the chassis. 2. Tighten the screw to secure the access panel to the chassis. 3. Install battery . 4. Follow the procedures in After Working Inside Your computer . Removing the Hard Drive 1. Follow the procedures in Before Working Inside Your Computer .
Installing the Hard Drive 1. Slide the hard drive into the connector. 2. Tighten the screw to secure it to the chassis. 3. Install: a. access panel b. battery 4. Follow the procedures in After Working Inside Your computer . Removing the Memory Module 1.
Installing the Memory Module 1. Insert the memory module into the socket and press to lock the securing clips. 2. Install the access panel . 3. Install the battery . 4. Follow the procedures in After Working Inside Your computer . Removing the WLAN Card 1.
a. access panel b. battery 4. Follow the procedures in After Working Inside Your Computer . Removing the Keyboard 1. Follow the procedures in Before Working Inside Your Computer . 2. Release the keyboard by pressing the tabs using a scribe. 3. Slide and lift the keyboard to access the cable below.
Installing the Keyboard 1. Connect the keyboard cable to the connector on the system board. 2. Slide the keyboard into the retaining slots. 3. Press the top edge to lock the keyboard in place. 4. Install the battery. 5. Follow the procedures in After Working Inside Your Computer .
6. Turn the computer over and remove the screws from inside the keyboard cavity. Then, disconnect the touchpad and power cables from the system board. 7.
Installing the Palmrest Assembly 1. Place the palmrest on the chassis and press the notches until it clicks in place. 2. Connect the touchpad and power cables to the system board. 3. Tighten the screws to secure it to the system board. 4. Turn the computer over and tighten the screws at the base of the computer.
Installing the Coin-cell battery 1. Insert the coin-cell battery and press to lock. 2. Install: a. palmrest assembly b. keyboard c. memory module d. hard drive e. WLAN card f. access panel g. optical disk-drive h. battery 3. Follow the procedures in After Working Inside Your computer .
Installing the Input/Output (I/O) Board 1. Insert the I/O board into the chassis. 2. Connect the I/O board cable to the system board. 3. Install: a. palmrest assembly b. keyboard c. memory module d. hard drive e. WLAN card f. access panel g. optical disk-drive h.
4. Release the speaker assembly from the retaining clips (1) and remove the speakers from the chassis (2). Installing the Speakers 1. Insert the speakers into the chassis and press the retaining clips to lock in place. 2. Connect the speakers to the system board.
e. WLAN card f. access panel g. optical disk-drive h. battery 4. Follow the procedures in After Working Inside Your computer . Removing the System Board 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove: a. battery b. optical-disk drive c.
5. Lift and remove the system board from the chassis. Installing the System Board 1. Insert the system board into the chassis. 2. Connect the I/O board connector to the system board. 3. Connect the eDP cable to the system board. 4. Connect the speakers to the system board.
b. keyboard c. memory module d. hard drive e. WLAN card f. access panel g. optical disk-drive h. battery 8. Follow the procedures in After Working Inside Your computer . Removing the Display Assembly 1. Follow the procedures in Before Working Inside Your Computer .
5. Remove the screws that secure the display hinges to the display assembly. Then, lift and remove the display hinges away from the display assembly. 6. Remove the screws securing the display panel to the display assembly. Then, flip the display panel to access the cables underneath.
7. Perform the following steps as shown in the illustration: a. Lift the eDP cable from the computer [1]. b. Disconnect the eDP cable. c. Remove the display panel from the computer [3]. Installing the Display Assembly 1. Connect the eDP cable to the display panel.
6. Install: a. system board b. palmrest assembly c. keyboard d. memory module e. hard drive f. access panel g. optical disk-drive h. battery 7. Follow the procedures in After Working Inside Your computer . Removing the Camera 1. Follow the procedures in Before Working Inside Your Computer .
Installing the Camera 1. Insert the camera into the display assembly. 2. Connect the camera cable. 3. Install: a. display assembly b. palmrest assembly c. keyboard d. memory module e. hard drive f. WLAN card g. access panel h. optical disk-drive i. battery 4.
Installing the Heatsink Assembly 1. Insert the heatsink and tighten the screws to secure it to the system board. 2. Connect the system fan’s cable to the system board. 3. Install: a. system board b. palmrest assembly c. keyboard d. memory module e. hard drive f.
b. Unroute the cable from the retention clips [2]. c. Lift the power connector from the computer [3]. Installing the Power Connector 1. Insert the power connector into its slot on the chassis and guide the cable into the retention tabs. 2. Connect the power connector cable to the system board.
3 System Setup System Setup enables you to manage your computer hardware and specify BIOS ‐ level options. From the System Setup, you can: • Change the NVRAM settings after you add or remove hardw.
Table 1. Navigation Keys Keys Navigation Up arrow Moves to the previous field. Down arrow Moves to the next field. <Enter> Allows you to select a value in the selected field (if applicable) or follow the link in the field. Spacebar Expands or collapses a drop ‐ down list, if applicable.
Option Description CPU Speed Displays the speed of the processor. CPU ID Displays the processor ID. CPU Cache L1 Cache Displays the processor L1 cache size. L2 Cache Displays the processor L2 cache size. L3 Cache Displays the processor L3 cache size. Fixed HDD Displays the model number and capacity of the hard drive.
Option Description Integrated NIC Enable or disable the power supply to the on– board network card. Default: Enabled USB Emulation Enable or disable the USB emulation feature. Default: Enabled USB Wake Support Allows USB devices to wake up the computer from standby.
The Security tab displays the security status and allows you to manage the security features of the computer. Table 4. Security Options Option Description Unlock Setup Status Admin Password Status Thi.
Option Description Boot Option #3 Default: Onboard NIC (IPV4) Boot Option #4 Default: Onboard NIC (IPV6) Exit — This section allows you to save, discard, and load default settings before exiting from System Setup. Updating the BIOS It is recommended to update your BIOS (system setup), on replacing the system board or if an update is available.
CAUTION: The password features provide a basic level of security for the data on your computer. CAUTION: Anyone can access the data stored on your computer if it is not locked and left unattended. NOTE: Your computer is shipped with the system and setup password feature disabled.
NOTE: If you change the System and/or Setup password, re-enter the new password when promoted. If you delete the System and/or Setup password, confirm the deletion when promoted. 5. Press <Esc> and a message prompts you to save the changes. 6. Press <Y> to save the changes and exit from the System Setup.
4 Diagnostics Enhanced Pre-Boot System Assessment (ePSA) Diagnostics The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware.
5 Specifications Specifications NOTE: Offerings may vary by region. For more information regarding the configuration of your computer, click Start (Start icon) → Help and Support , and then select the option to view information about your computer. Table 6.
Table 9. Audio Feature Description Type 2 channel high-definition audio Controller Realtek ALC3234 Stereo conversion 24-bit (analog-to-digital and digital-to-analog) Interface Intel HDA bus Speakers 2 x 2 W Volume controls program menu and keyboard media-control keys Table 10.
Feature Description • two USB 2.0 ports NOTE: The powered USB 3.0 connector also supports Microsoft Kernel Debugging. The ports are identified in the documentation shipped with your computer. Media card reader one SD slot Table 14. Display Feature Type 14.
Table 17. Battery Feature Description Type • 4-cell “smart” lithium ion (40 WHr) Dimensions: Height 20.00 mm (0.79 inch) Width 272.40 mm (10.72 inches) Depth 46.30 mm (1.82 inches) Weight 0.26 kg (0.57 lb) Life span 300 discharge/charge cycle Voltage • 14.
Table 20. Environmental Feature Description Temperature: Operating 0 °C to 40 °C (32 °F to 104 °F) Storage –40 °C to 65 °C (–40 °F to 149 °F) Relative humidity (maximum): Operating 10 % to 90 % (non-condensing) Storage 0 % to 95 % (non-condensing) Altitude (maximum): Operating –15.
6 Contacting Dell Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options.
Een belangrijk punt na aankoop van elk apparaat Dell P52G (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Dell P52G heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Dell P52G vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Dell P52G leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Dell P52G krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Dell P52G bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Dell P52G kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Dell P52G . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
