Gebruiksaanwijzing /service van het product SC1435 van de fabrikant Dell
Ga naar pagina of 132
www .dell.com | support.dell.com Dell™ PowerEdge™ SC 1435 Sy stems Hardware Owner’ s Manual.
Notes, Notices, and Cautions NOTE: A NOTE indicates important i nformation that helps you make better use of your computer . NOTICE: A NOTICE indicates either potential da mage to hardware or loss of da ta and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potential for propert y damage, personal injury , or death.
Contents 3 Contents 1 About Y our Sy stem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Other Information Y ou May Need . . . . . . . . . . . . . . . . . . . . . . . . . 9 Accessing Sy stem Featur es During Startup . . . . . . . . . . . .
4 Contents Disabling a Forgotten Password . . . . . . . . . . . . . . . . . . . . . . . . . 33 Baseboard Management Controller Configuration . . . . . . . . . . . . . . . 33 Entering the BMC Setup Module . . . . . . . . . . . . . . . . . . . . . . 34 BMC Setup Module Options .
Contents 5 Optical Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Removing the Optical Drive from the Sy stem . . . . . . . . . . . . . . . . 54 Installing the Optical Drive in the Sy stem . . . . . . . . . . . . . . . .
6 Contents T roubleshooting Basic I/O Functions . . . . . . . . . . . . . . . . . . . . . . 70 T roubleshooting a Serial I/O Device . . . . . . . . . . . . . . . . . . . . 71 T roubleshooting a USB Device . . . . . . . . . . . . . . . . . . . . . . . 71 T roubleshooting a NIC .
Contents 7 6 Jumpers and Connectors . . . . . . . . . . . . . . . . . . . . . . . . 89 Sy stem Board Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Disabling a Forgotten Password . . . . . . . . . . . . . . . . . . . . . . . . .
8 Contents.
About Y our Sy stem 9 About Y our Sy stem This section describes the physical, firmware, and softwar e interface features that provide and ensure the essential functioning of your system. The ph ysical connectors on your system’s front and back panels provide convenient connectivity and system expansion capability .
10 About Y our Sy stem • Updates ar e sometimes included with the system to describe changes to the system, software, and/or documentation. NOTE: Alway s check for updates on support.dell.com and read the updates first because they often supersede information in other documents.
About Y our Sy stem 11 Front-Panel Features and Indicators F igure 1-1 shows the controls, indicators, and connec tors located behind the optional rack bezel on the system's front panel. Figure 1-1. Front-Panel Features and Indicators 6 5 4 3 2 1 8 7 T able 1-2.
12 About Y our Sy stem 4 Diagnostics indicator lights (4) The four di agnostic indicator lights on the system front panel display error codes during system startup.
About Y our Sy stem 13 Back-Panel Features and Indicators F igure 1-2 shows the controls, indicators, and co nnectors located on the system's back panel.
14 About Y our Sy stem NIC Indicator Codes Each NIC on the back panel has an indicator that provides informa tion on network activity and link status. See F igure 1-3.
About Y our Sy stem 15 T able 1-5. Diagnostic Indicator Codes Code Causes Corrective Action P ossible processor failure. See "T roubl eshooting the Microprocessors" on page 82. Memory failure. See "T roubleshooting System Memory" on page 76.
16 About Y our Sy stem Sy stem Messages System messages appear on the screen to notify you of a possible problem with t he system. T able 1-6 lists the system messages that can occur and the probab le cause and corrective action for each message.
About Y our Sy stem 17 Diskette drive n seek failure Incorrect configuration settings in the System Setup program. R un the System Setup program to correct the settings. See "Using the System Setup P rogram" on page 23. F aulty or improperly installed diskette drive.
18 About Y our Sy stem General failure The operating system is unable to carry out the command. This message is usually followed by specific information. Note the information and take the appropriate action to resolve the problem. Invalid NVRAM configuration, Resource Re-allocated System detected and corrected a resource conflict.
About Y our Sy stem 19 No boot sector on hard drive Incorrect configuration settings in System Setup program, or no operating system on hard drive. Check the hard-drive configuration settings in the System Setup program. See "Using the System Setup P r ogram" on page 23.
20 About Y our Sy stem Read fault Requested sector not found The operating system cannot read from the diskette or har d drive, the system could not find a particular sector on the disk, or the requested sector is defective. Replace the diskette. Ensur e that the diskette and har d drive cables are properly connected.
About Y our Sy stem 21 Time-of-day not set - please run SETUP program Incorrect T ime or Date settings; faulty system battery . Check the Time and Date settings. See "Using the System Setup P rogram" on page 23. If the problem persists, replace the system battery .
22 About Y our Sy stem W arning Messages A warning message alerts you to a po ssible problem and prompts you to respond befor e the system continues a task. F or example, before you format a disk ette, a message will warn you that you may lose all data on the diskette.
Using the Sy stem Setup Program 23 Using the Sy stem Setup Program After you set up your system, run the System Setup program to familiarize yourself with your system configuration and optional settings.
24 Using the Sy stem Setup Program Using the Sy stem Setup Program T able 2-1 lists the ke ys that you use to view or ch ange information on the System Setup program screens and to exit the program. NOTE: For most of the options, any changes that you make are recorded but do not take effect until you restart the sy stem.
Using the Sy stem Setup Program 25 Figure 2-1. Main Sy stem Setup Program Screen T able 2-2 lists the options and desc riptions for the information fields that appear on the main System Setup program screen. F or related information, s ee "System Security Scr een Options" on page 29.
26 Using the Sy stem Setup Program Boot Sequence Determines the order in which the system searches for boot devices during system startup. Available options ca n include the disk ette drive, CD drive, hard drives, and network. NOTE: Sy stem boot is not supported from an external device attached to a SAS or SCSI adapter .
Using the Sy stem Setup Program 27 Memory Information Screen T able 2-3 lists the descriptions for the in formation fields that appear on the Memory Information screen. CPU Information Screen T able 2-4 lists the options and descriptions for the information fields that appear on the CPU Information screen.
28 Using the Sy stem Setup Program Enabling AMD™ PowerNow!™ T echnology P owerNow! technology controls your system’s processor performance automatically , dynamically adjusting the operating frequency and voltage accor ding to the task at hand. When an application does not requir e full performance, signific ant amounts of power can be saved.
Using the Sy stem Setup Program 29 Sy stem Security Screen T able 2-6 lists the options and descriptions for the information fields that appear on the System Security screen.
30 Using the Sy stem Setup Program Exit Screen After you press <Es c> to exit the System Setup program, the Exit screen displays the following options: • Save Changes and Exit • Discard Chan.
Using the Sy stem Setup Program 31 When a system password is assigned, the setting shown for the System P assword option is Enabled . If the setting shown for the P assword Status is Unlocked , you can change the system password. If the P assword Status option is Loc ked , you cannot change the system pa ssword.
32 Using the Sy stem Setup Program When the P assword Status option is set to Loc ked whenever you turn on your system or reboot your system by pressing <Ctrl><Alt><Del>, type yo ur passwor d and press <Enter> at the prompt. After you type the correct system passwor d and press <Enter>, your system operates as usual.
Using the Sy stem Setup Program 33 The password assignment is not case-sensitive. Howeve r , certain key combinations ar e not valid. If you enter one of these combinations, t he system beeps. T o erase a ch aracter when entering your password, press <Backspace> or the left-arrow k ey .
34 Using the Sy stem Setup Program • Support is independent of the system’s power or operating state • P rovides text console redir ection for system setup, text-based utilities, and operating system consoles NOTE: T o remotely access the BMC through the integrated NI C, you must connect th e network connection to integrated NIC1.
Installing Sy stem Components 35 Installing Sy stem Components This section describes how to ins tall the following system components: • F ront bezel • System cover • Cooling shroud • Cooling .
36 Installing Sy stem Components Inside the Sy stem CAUTION: Only trained service technicians ar e authorized to remove the sy st em cover and access any of the components inside the sy stem.
Installing Sy stem Components 37 The system provides space for one op tional slimline optical drive. F or more information, see "Installing the Optical Drive in the System" on page 54. The hard-drive bays provide space for one or two 3 .5-inch har d drives.
38 Installing Sy stem Components Opening and Closing the Sy stem CAUTION: Only trained service technicians ar e authorized to remove the sy st em cover and access any of the components inside the sy stem.
Installing Sy stem Components 39 Closing the Sy stem 1 Lift up the latch on the cover . 2 Align the cover with the left and right edges of the sy stem and offset it slightly towards the back of the system, so that the pins on the inner edge of the cover are aligned with the chassis J hooks.
40 Installing Sy stem Components Figure 3-4. Cooling Shroud Replacing the Cooling Shroud 1 T o install the cooling shroud, align the edges of the shroud with the six locator pins on the system board. See F igure 3-4. 2 Lower the shroud into place over the system board.
Installing Sy stem Components 41 4 Unplug the fan module power connector fr om the system board. See F igure 3-5. 5 Remove the screw from the fan module r etention plate and remove the r etention plate from the chassis. 6 Lift the fan module straight up from the chassis.
42 Installing Sy stem Components 5 Reinstall the cooling shroud. See "Replacing the Cooling Shroud" on page 40. 6 Close the system. See "Opening and Closing the System" on page 38.
Installing Sy stem Components 43 Figure 3-6. Removing an d Installing a Power Supply Installing the Power Supply NOTICE: On a rack sy stem, you may need to temporarily unlatch and lift the cable management arm. For information about the cable manag ement arm, see the sy stem’ s Rack Installation Guide .
44 Installing Sy stem Components Expansion Cards The system supports one half -length expansion card. T wo different PCI riser boar d configurations are available: • The PCIe riser has one x8-lane width PCIe expansion slot. • The PCI- X riser has one 64-bit/133-MHz expansion slot.
Installing Sy stem Components 45 Figure 3-7. Installing an Expansion Card Removing an Expansion Card CAUTION: Only trained service technicians ar e authorized to remove the sy st em cover and access any of the components inside the sy stem.
46 Installing Sy stem Components 5 If you are r emoving the card permanently , install a metal filler brack et over the empty expansion slot opening and close the expansion-car d latch. NOTE: Y ou must install a f iller bracket over an empty expansion slot to maintai n Federal Communications Commission (FCC) certification of the sy stem.
Installing Sy stem Components 47 Single-Processor Memory Configurations Y ou can use the following configurations in a single-processor system. T able 3-1.
48 Installing Sy stem Components Non-Optimal Memory Configurations System performance can be affected if your memory configuration does not conform to the preceding installation guidelines. Y our system may issue an error message during startup stating that your memory configuration is non-optimal.
Installing Sy stem Components 49 6 Align the memory module's edge connector with the alignment key of the memory module sock et, and insert the memory module in the socket. NOTE: The memory module socket has an alignment key that allows you to install the memory module in the socket in only one way .
50 Installing Sy stem Components 5 Replace the cooling shroud. See "Repl acing the Cooling Shroud" on page 40. 6 Close the system. See "Opening and Closing the System" on page 38. Processors Y ou can upgrade your processor(s) to take advantage of futur e options in speed and functionality .
Installing Sy stem Components 51 Figure 3-9. Installing and Removing the Heat Sink 6 W ait 30 seconds for the heat sink to loosen from the processor . 7 If the heat sink has not separated from the processor , carefully rotate the heat sink in a clockwise, then counterclockwise, direction until it r eleases from th e processor .
52 Installing Sy stem Components Figure 3-10. Installing and Removing the Processor 11 Open the processor shield and then lift the processo r out of the socket. Leave the release lever up so that the socket is r eady for the new processor . NOTICE: Be careful not to bend any of the pins on the LGA so cket when removing the processor .
Installing Sy stem Components 53 4 I nstall the processor in the socket. NOTICE: Positioning the processor incorrectl y can permanently damage the sy stem board or the processor when you turn the sy stem on. a If the release lever on the processor sock et is not fully open, move it to that position.
54 Installing Sy stem Components Optical Drive The optional slimline optical drive is mounted on a tray that slides into the front panel. NOTE: DVD devices are data only .
Installing Sy stem Components 55 Figure 3-11. Removing and Installing the Optical Drive Removing the Optical Drive from the Drive T ray 1 Remove the interposer board from the drive by deflecting the tab at each end of the boar d.
56 Installing Sy stem Components Optional SAS RAID Controller If you install the optional SAS R AID controller card, you can install two SAS or SA T A hard drives and configure them for R AID 0 or RAID 1 operation. • See "Expansion Cards" on page 44 for information on installing the optional SAS RAID controller car d.
Installing Sy stem Components 57 Figure 3-12. Installing a Hard-Drive Configuring the Boot Device If you plan to boot the system from a hard drive, the drive must be attached to the primary (or boot) controller . The device that the system boots from is determined by the boot order specified in the System Setup program.
58 Installing Sy stem Components Expansion-Card Riser Removing an Expansion-Card Riser CAUTION: Only trained service technicians are authorized to remove the sy stem cover and access any of the components inside the sy stem.
Installing Sy stem Components 59 Installing an Expansion-Card Riser CAUTION: Only trained service technicians ar e authorized to remove the sy st em cover and access any of the components inside the sy stem.
60 Installing Sy stem Components 5 Remove the system battery . a Support the battery connector by pressing down firmly on the positive side of the connector . b While supporting the battery connector , press th e battery towar d the positive side of the connector and pry it up out of the securing tabs at the negative side of the connector .
Installing Sy stem Components 61 14 After an hour , reconnect the system to i ts electrical outlet and turn it on. 15 Enter the System Setup program and if the time and date are still incorr ect, see "Getting Help" on page 95 for instructions on obtaining technical assistance.
62 Installing Sy stem Components Figure 3-15. Control Panel Re moval and Installation Installing the Control Panel CAUTION: Only trained service technicians ar e authorized to remove the sy st em cover and access any of the components inside the sy stem.
Installing Sy stem Components 63 Sy stem Board (Service-Only Procedure) Removing the Sy stem Board CAUTION: Only trained service technicians ar e authorized to remove the sy st em cover and access any of the components inside the sy stem.
64 Installing Sy stem Components Figure 3-16. Sy stem Board Removal Installing a Sy stem Board 1 Install the heatsink(s) and microprocessor(s ). See "Installing a P rocessor" on page 52 2 Install the memory modules in their original lo cations.
Installing Sy stem Components 65 12 Close the system. See "Opening and Closing the System" on page 38. 13 Connect the external cables to the system. 14 Reconnect the system to the power source and turn on the system and attached peripherals.
66 Installing Sy stem Components.
T roubleshooting Y our Sy stem 67 T roubleshooting Y our Sy stem Safety First—For Y ou and Y our Sy stem T o perform certain procedures in this document, you must r emove the system cover and work inside the system.
68 T roubleshooting Y our Sy stem Checking Basic Power Problems 1 If the power indicator on the system front panel or power supply does not indicate that power is available to the system, ensure that the power cable is securely connected to the power supply .
T roubleshooting Y our Sy stem 69 T roubleshooting External Connections Loose or improperly connected cables are the most likely source of proble ms for the system, monitor , and other peripherals (such as a printer , keyboar d, mouse, or other external device).
70 T roubleshooting Y our Sy stem T roubleshooting the Keyboard Problem • System message indicates a problem with the keyboar d • K eyboard is not functioning properly Action 1 Enter the System Setup program and ensure that th e USB ports ar e enabled.
T roubleshooting Y our Sy stem 71 Action 1 Enter the System Setup program and ensure that the serial port is enabled, and the serial port/COM ports are configur ed appropriately for any applicat ions you are using. See "Using the System Setup P rogram" on page 23.
72 T roubleshooting Y our Sy stem 5 If possible, swap the interface cable with a working cable. If the problem is resolved, r eplace the int erface cable. See "Getting Help" on page 95. 6 T urn off the system and th e USB device, and sw ap the device with a comparable device.
T roubleshooting Y our Sy stem 73 Action CAUTION: Only trained service technicians ar e authorized to remove the sy st em cover and access any of the components inside the sy st em.
74 T roubleshooting Y our Sy stem 5 R un the system board tests in the system diagn ostics. See "R unning the System Diagnostics" on page 86. If the tests fail, see "Getting Help" on page 95. T roubleshooting the Sy stem Battery Problem • System message indicates a problem with the battery .
T roubleshooting Y our Sy stem 75 2 Replace the faulty power supply with a new p ower supply . See "P ower Supply" on page 42. If the problem is not resolved, see ""Getting Help" on page 95." Problem • P ower button is not blinking gree n and the system does not power up.
76 T roubleshooting Y our Sy stem Action CAUTION: Only trained service technicians ar e authorized to remove the sy st em cover and access any of the components inside the sy st em.
T roubleshooting Y our Sy stem 77 3 T urn on the system and attached peripherals and, as the system boots, note the messages on the screen. If the amount of system memory detected during POST does not match the amount of memory installed, proceed to the next step.
78 T roubleshooting Y our Sy stem T roubleshooting an Optical Drive Problem • System cannot read data from a CD or D VD in an optical drive. • Optical drive indicator do es not blink during boot.
T roubleshooting Y our Sy stem 79 NOTICE: This troubleshooting procedure can destroy data stored on the hard dr ive. Before you proceed, back up all files on the hard drive. 1 R un the appropriate online diagnostic test. See "Using Dell P owerEdge Diagnostics" on page 85.
80 T roubleshooting Y our Sy stem Action CAUTION: Only trained service technicians ar e authorized to remove the sy st em cover and access any of the components inside the sy st em.
T roubleshooting Y our Sy stem 81 Action CAUTION: Only trained service technicians ar e authorized to remove the sy st em cover and access any of the components inside the sy st em.
82 T roubleshooting Y our Sy stem T roubleshooting the Microprocessors Problem • Error message indicates a processor problem. • A heat sink is not installed for each processor . Action CAUTION: Only trained service technicians ar e authorized to remove the sy st em cover and access any of the components inside the sy st em.
T roubleshooting Y our Sy stem 83 18 R un the appropriate online diagnostic test. If the tests complete successfully , replace processor 1. See "Getting Help" on page 95. 19 T urn off the system and attached peripherals, and di sconnect the system from the electrical outlet.
84 T roubleshooting Y our Sy stem.
Running the Sy stem Diagnostics 85 Running the Sy stem Diagnostics If you experience a problem with your system, run th e diagnostics befor e calling for technical assistance. The purpose of the diagnostics is to test your syst em's hardwar e without requiring additional equipment or risking data loss.
86 Running the Sy stem Diagnostics When to Use the Sy stem Diagnostics If a major component or device in the system does not operate properly , component failure may be indicated.
Running the Sy stem Diagnostics 87 Using the Custom T est Options When you select Custom T est in the Main Menu window , the Customize window appears and allows you to select the device(s) to be tested, select specif ic options for testing, and view the test results.
88 Running the Sy stem Diagnostics.
Jumpers and Connectors 89 Jumpers and Connectors This section provides specific information about t he system jumpers. It also provides some basic information on jumpers and switches and describ es the connectors on the various boards in the system.
90 Jumpers and Connectors Disabling a Forgotten Password The system's software security featur es include a system password and a setup passwor d, which are discussed in detail in "Using the System Setup P rogram" on page 23.
Jumpers and Connectors 91 7 T urn off the system, including any attached periphera ls, and disconnect the system from the electrical outlet. 8 Open the system. See "Opening and Closing the System" on page 38. 9 Install the jumper plug on the password jumper .
92 Jumpers and Connectors Sy stem Board Connectors See F igure 6-2 and T able 6-2 for the location and description of system board connectors. Figure 6-2.
Jumpers and Connectors 93 T able 6-2. Sy stem Board Connectors Connector Description 1 RISER Riser board connector 2 DIMM5 Memory module connector , slot 5 3 DIMM6 Memory module connector , slot 6 4 D.
94 Jumpers and Connectors Riser Boards This system supports a riser board with one PCIe e xpa nsion slot (F igure 6-3), or a riser board with one PCI- X expansion slot (F igure 6-4).
Getting Help 95 Getting Help T echnical Assistance If you need assistance with a technical problem, perform the following steps: 1 Complete the procedures in "T roubleshooting Y our System" on page 67. 2 R u n the system diagnostics and recor d any information provided.
96 Getting Help www .euro .dell.com (Europe only) www .dell.com/la (Latin American countries) www .dell.ca (Canada only) • Anonymous file transfer protocol (FTP) ftp.dell.com/ Log in as user:anonymous , and use your e-mail address as your passwor d.
Getting Help 97 Dell Enterprise T raining and Certification Dell Enterprise T raining and Certification is available; see www .dell.com/training for more information.
98 Getting Help Before Y ou Call NOTE: Have your Express Service Code r eady when you call. The code helps Dell 's automated-support telephone sy stem direct your call more efficiently .
Getting Help 99 Diagnostics Checklist Name: Date: Address: Phone number: Service T ag (bar code on the back of the computer): Express Servi ce Code: Return Material Authorization Number ( if provided .
100 Getting Help Contacting Dell T o contact Dell electronically , you can access the following websites: • www .dell.com • support.dell.com (support) F or specific web addresses for yo ur country , find the appropriate co untry section in the table below .
Getting Help 101 Argentina (Buenos Aires) International Access Code: 00 Country Code: 54 City Code: 11 W ebsite: www .dell.com.ar E-mail: la-techsupport@dell.com E-mail for desktop and portable computers: la-techsupport@dell.com E-mail for servers and EMC ® storage products: la_enterprise@dell.
102 Getting Help Barbados W ebsite: www . dell.com/bb E-mail: la-techsupport@dell.com General Support 1-800-534-3142 Belgium (Brussels) International Access Code: 00 Country Code: 32 City Code: 2 We b s i t e : support.
Getting Help 103 Canada (North Y ork, Ontario) International Access Code: 011 Online Order Status: www .dell.ca/ostatus W ebsite: support.ca.dell.com AutoT ech (automated Hardwar e and W arranty Support) toll-free: 1-800-247-9362 Customer Service (Home/Home Office) toll-free: 1-800-847-4096 Customer Service (small/med.
104 Getting Help China (Xiamen) Country Code: 86 City Code: 592 T echnical Support website: support.dell.com.cn T echnical Support E-mail: support.dell.
Getting Help 105 Costa Rica W ebsite: www .dell.com/cr E-mail: la-techsupport@dell.com General Support 0800-012-0231 Czech Republic (P rague) International Access Code: 00 Country Code: 420 W ebsite: support.
106 Getting Help El Salvador We b s i t e : www .dell.com/ec E-mail: la-techsupport@dell.com General Support 800-6132 F inland (Helsinki) International Access Code: 990 Country Code: 358 City Code: 9 We b s i t e : support.euro.dell.com E-mail: fi_support@dell.
Getting Help 107 Germany (F rankfurt) International Access Code: 00 Country Code: 49 City Code: 69 W ebsite: support.euro.dell.com E-mail: tech_support_central_europe@dell.
108 Getting Help Hong Kong International Access Code: 001 Country Code: 852 W ebsite: support.ap.dell.com T echnical Support E-mail: support.dell.com.cn/email T echnical Support (XPS) 00852-3416 6923 .
Getting Help 109 Ireland (Cherrywood) International Access Code: 00 Country Code: 353 City Code: 1 W ebsite: support.euro.dell.com E-mail: dell_direct_support@dell.
110 Getting Help Jamaica E-mail: la-techsupport@dell.com General Support (dial from within Jamaica only) 1-800-440-9205 Japan (Kawasaki) International Access Code: 001 Country Code: 81 City Code: 44 We b s i t e : support.
Getting Help 111 Korea (Seoul) International Access Code: 001 Country Code: 82 City Code: 2 E-mail: krsupport@dell.com Support toll-free: 080-200-3800 T echnical Support (XPS) toll-free: 080-999-0283 .
112 Getting Help Malaysia (P enang) International Access Code: 00 Country Code: 60 City Code: 4 We b s i t e : support.ap.dell.com T echnical Support (XPS) toll-free: 1800 885 784 T echnical Support (.
Getting Help 113 Netherlands (Amsterdam) International Access Code: 00 Country Code: 31 City Code: 20 W ebsite: support.euro.dell.com T echnical Support for XPS 020 674 45 94 T echnical Support for al.
114 Getting Help P oland (W arsaw) International Access Code: 011 Country Code: 48 City Code: 22 We b s i t e : support.euro.dell.com E-mail: pl_support_tech@dell.
Getting Help 115 Singapore (Singapore) International Access Code: 005 Country Code: 65 NOTE: The phone numbers in th is section should be called from within Singap ore or Mala y sia only .
116 Getting Help Spain (Madrid) International Access Code: 00 Country Code: 34 City Code: 91 We b s i t e : support.euro.dell.com Home and Small Business T echnical Support 902 100 130 Customer Care 9.
Getting Help 117 Ta i w a n International Access Code: 002 Country Code: 886 W ebsite: support.ap.dell.com E-mail: support.dell.com.cn/email T echnical Support (XPS) toll-free: 0080 186 3085 T echnica.
118 Getting Help U.K. (Bracknell) International Access Code: 00 Country Code: 44 City Code: 1344 We b s i t e : support.euro.dell.com E-mail: dell_direct_support@dell.
Getting Help 119 U.S.A. (Austin, T exas) International Access Code: 011 Country Code: 1 Automated Or der-Status Service toll-free: 1-800-433-9014 AutoT ech (portable and desktop computers) toll-free: .
120 Getting Help U.S. V irgin Islands E-mail: la-techsupport@dell.com General Support toll-free: 1-877-702-4360 V enezuela We b s i t e : www .dell.com/ve E-mail: la-techsupport@dell.
Glossary 121 Glossary This section defines or identifies technical terms, abbreviations, and acronyms used in your system documents. A — Ampere(s). AC — Alternating current. ACP I — Advanced Configuration and P ower Interface. A standard interface for enabling the operating system to direct configuration and power management.
122 Glossary CD — Compact disc. CD drives use optical technology to read data from CDs. cm — Centimeter(s). cmos — Complementary metal-oxide semiconductor . component — As they relate to DMI, components include operating systems, computer systems, e xpansion cards, and peripherals that ar e compatible with DMI.
Glossary 123 expansion-card connector — A connector on the system board or riser boar d for plug ging in an expansion car d. F — F ahrenheit. FAT — File allocation table. The file system structur e used by MS-DOS to organize and k eep track of file storage.
124 Glossary KB — Kilobyte(s); 1024 bytes. Kbps — Kilobit(s) per second. KBps — Kilobyte(s) per second. key combination — A command requiring you to pr ess multiple keys at the same time (for e xample, <Ctrl><Alt><Del>). kg — Kilogram(s); 1000 grams.
Glossary 125 NTFS — The NT F ile System option in the W indows 2000 operating system. NVRAM — Nonvolatile random-access memory . Memory that does not lose its contents when you turn off your system. NVRAM is used for maintaining the date, time, and system configuration information.
126 Glossary SA T A — Serial Advanced T e chnology Attachment. A standard interface between the system boar d and storage devices. SCSI — Small computer system interface. An I/O bus interface with faster data tran smission rates than standard ports.
Glossary 127 UPS — Uninterruptible power supply . A battery-powered unit that automatically supplies power to your system in the event of an electrical failure. USB — Universal Serial Bus. A USB connector provides a single connection point fo r multiple USB-compliant devices, such as mice and ke yboar ds.
128 Glossary.
Index 129 Index A alert messages, 22 B back-panel features, 13 baseboard management controller . See BMC. battery replacing, 5 9 troubleshooting, 7 4 bezel removing, 3 7 replacing, 3 7 BMC configuration, 3 3 setup module, 1 0 boot device configuring, 5 7 C CD/D VD drive See optical drive.
130 Index 130 Index I indicators back-panel, 1 3 front-panel, 1 1 NIC, 1 4 power , 1 3 installing control panel assembly , 6 2 expansion car d, 4 4 expansion-car d riser board, 5 9 memory modules, 4 8.
Index 131 rep l ac in g cooling fan module, 4 1 power supply , 4 3 processor , 5 0 system battery , 5 9 S safety , 67 SAS configuration utility entering, 1 0 SAS hard drives, 55 SAS R AID controller i.
132 Index 132 Index.
Een belangrijk punt na aankoop van elk apparaat Dell SC1435 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Dell SC1435 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Dell SC1435 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Dell SC1435 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Dell SC1435 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Dell SC1435 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Dell SC1435 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Dell SC1435 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.