Gebruiksaanwijzing /service van het product (Model 31-695) van de fabrikant Delta
Ga naar pagina of 21
INSTRUCTION MANUAL P ART NO. 902122 - 02-20-04 Copyright © 2004 Delta Machinery ESP AÑOL: PÁGINA 21 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury .
3 GENERAL SAFETY RULES 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly minimize the possibility of accidents and injury . 2. WEAR EYE PROTECTION.
4 ADDITIONAL SAFETY RULES FOR ABRASIVE FINISHING MACHINES 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according to the instructions.
5 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug.
6 EXTENSION CORDS Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wire extension cor d which has a 3-prong gr ounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine.
7 Fig. 2 1. Sander with 6" x 48" Sanding Belt and Backstop 2. Sanding Disc Plate 3. Belt and Pulley Cover 4. 9" Sanding Disc 5. Plug 6. T -Wrench 7. Drive Belt 8. M6 x 55mm Hex Socket Head Screws (2) 9. M6.4 Flat Washer (2 10. M6.4 Lockwasher (2) 11.
8 For your own safety , do not connect the machine to the power source until the machine is completely assembled and you read and understand the entir e instruction manual. ASSEMBL Y ST AND Any letter designations that are stamped on the braces of the stand are for pr oduction purposes ONL Y and are not used for assembling the stand.
9 BEL T AND PULLEY GUARD Place an M6.4 lockwasher and an M6.4 flat washer in that order on two M6 x 55mm hex socket head scr ews (B), and attach the belt and pulley guard (A) Fig. 8 to the machine. NOTE: Install the plug (C) in the guard. C SANDING DISC PLA TE 1.
10 Fig. 13 LOWER COVER FOR SANDING DISC Use three M4.2 x 13mm pan head scr ews (C) to attach the lower cover (A) Fig. 13 to the belt and pulley guard (B). Prevent the sanding disc fr om contacting the lower cover . Rotate the sanding disc by hand to ensure that no contact is made.
11 Fig. 17 LOCKING SWITCH IN THE “OFF” POSITION When the machine is not in use, the switch should be locked in the “OFF” position to prevent unauthorized use. This can be done by grasping the switch toggle (B) and pulling it out of the switch, as shown in Fig.
12 Fig. 21 Fig. 22 ADJUSTING BACKSTOP SQUARE WITH SANDING BEL T 1. Before making this adjustment, check to see that the belt tension lever (A) Fig. 22 is all the way to the left in the “tighten” position. 2. Place a square (B) Fig. 23 on the sanding belt with the end of the square against the backstop.
13 SQUARING T ABLE WITH SANDING DISC 1. Place one end of a combination square (C) Fig. 25 on the table with the other end against the sanding disc. 2. If the table surface is not 90 degrees to the disc, loosen the table lock knob (A) Fig. 25, adjust the table, and tighten lock knob (A).
14 Fig. 30 Fig. 31 USING T ABLE ASSEMBL Y WITH SANDING BEL T Use the table assembly with the sanding belt in the vertical position ONL Y. T o move the table assembly (B) Fig. 30 to the sanding arm (A): 1. Remove the backstop (C) Fig. 30. 2. Loosen the screw (D) Fig.
15 2. If you are sanding with the belt, pull the dust shield (A) Fig. 34 outward. Fig. 35 Fig. 36 WRENCH STORAGE A hole is provided in the stand for storing the hex wr ench (A) Fig. 35, supplied with the sander . REMOVING UPPER SANDING DRUM GUARD Y ou can remove the upper sanding drum guard (A) Fig.
16 Fig. 39 Fig. 40 5. Place a new 6" x 48" sanding belt (F) Fig. 40 over both sanding drums (G). Ensure that the belt will travel in the direction of the arr ows printed on the inside of the belt. 6. Move the tension lever (E) Fig. 39 left to the “TIGHTEN” position.
17 Fig. 45 Fig. 44 SURF ACING OR EDGE SANDING WITH SANDING BEL T When surfacing (Fig. 44) or edge sanding (Fig. 45), place the sanding arm in the horizontal position and use the backstop (A) Fig. 44 and Fig. 45 to keep the workpiece in place. Hold the workpiece firmly and keep your fingers away from the sanding belt.
18 Fig. 48 END SANDING WITH THE DISC When sanding the ends of narrow workpieces, use the sanding disc and the accessory miter gauge (Fig. 48). Move the work from the center to the left side of the sanding disc. Always sand on the left (downward) side of the sanding disc.
19 MAINTENANCE KEEP MACHINE CLEAN Periodically blow out all air passages with dry compressed air . All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.
20 P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations.
The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.
Een belangrijk punt na aankoop van elk apparaat Delta (Model 31-695) (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Delta (Model 31-695) heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Delta (Model 31-695) vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Delta (Model 31-695) leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Delta (Model 31-695) krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Delta (Model 31-695) bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Delta (Model 31-695) kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Delta (Model 31-695) . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
