Gebruiksaanwijzing /service van het product 14070 van de fabrikant Delta
Ga naar pagina of 18
INSTRUCTION MANUAL 14" Floor Drill Pr ess P ART NO. 1046995 © Delta Machinery Inter national Machinery Corp. 1995 MODEL 14-070 Dated 6-30-95.
T ABLE OF CONTENTS SAFETY RULES 3 ADDITIONAL SAFETY RULES FOR DRILL PRESSES 4 UNP ACKING 5 CLEANING 6 ASSEMBL Y INSTRUCTIONS 6-9 F ASTENING DRILL PRESS TO A SUPPORTING SURF ACE 9 MOTOR SPECIFICA TIONS.
W oodworking can be dangerous if safe and pr oper operating procedures ar e not followed. As with all machinery , there are certain hazar ds involved with the operation of the product. Using the machine with respect and caution will consid- erably lessen the possiblity of personal injury .
ADDITIONAL SAFETY RULES FOR DRILL PRESSES 1. WARNING: DO NOT operate your drill pr ess until it is completely assembled and installed according to the instructions. 2. IF YOU ARE NOT thoroughly familiar with the opera- tion of drill presses, obtain advice fr om your supervisor , instructor or other qualified person.
UNP ACKING Carefully unpack the drill pr ess and all loose items from the carton. Figure 2 illustrates the drill pr ess and all loose items supplied with the machine.
CLEANING Remove the protective coating fr om the machined surfaces of the drill press and all loose items. This coating may be removed with a soft cloth moistened with ker osene. DO NOT use acetone, gasoline, or lacquer thinner for this pur- pose. ASSEMBL Y INSTRUCTIONS 1.
4. Insert raising rack (E) Fig. 5, which was removed in STEP 2, into groove in table bracket (H) making sure gear inside table bracket is engaged with teeth of raising rack. Fig. 7 Fig. 6 Fig. 5 5. Slide raising rack (E) Fig. 6, and table (J) onto drill press column, as shown.
7. Assemble table raising and lowering handle (M) Fig. 8, to shaft on table bracket and tighten set screw in han- dle against flat on shaft. 8. Thread table bracket lock scr ew (O) Fig. 8, into hole in table bracket, as shown. 9. Place the drill press head onto the column as far as it will go.
11. IMPORT ANT : Make certain the bottom of spindle (S) Fig. 11, and tapered hole (T) in chuck are clean and fr ee of any grease, lacquer or rust preventive coatings. NOTE: Household oven cleaner can effectively r emove any substance from the spindle and chuck; however , carefully follow the manufacturer’ s safety rules concer ning its use.
1. Drill two 3/8" diameter holes (C) Fig. 12B, correspon- ding to the mounting holes (A) Fig. 12A, of the drill press base in a 21" by 28" minimum size plywood board (D) Fig. 12B. 2. Fasten the drill press base to the mounting boar d using the carriage bolts, nuts, and washers (E) Fig.
CAUTION: THIS TOOL MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERA TOR FROM ELECTRIC SHOCK. In the event of a malfunction or breakdown, gr ounding provides a path of least resistance for electric curr ent to reduce the risk of electric shock.
SPINDLE SPEEDS T welve spindle speeds of 250, 360, 410, 540, 590, 650, 1090, 1280, 1450, 1820, 2180 and 3000 RPM are avail- able with the 14" Drill Press. Fig. 15, illustrates which steps of the pulleys the belts must be placed to obtain the twelve speeds.
CHANGING SPINDLE SPEEDS AND ADJUSTING BEL T TENSION 1. DISCONNECT THE DRILL PRESS FROM THE POWER SOURCE. 2. Lift up belt and pulley guard (A) Fig. 16. 3. Loosen tension lock knob (B) Fig. 16, along with the tension lock knob located on the other side of the head cast- ing.
SWITCH The switch (A) Fig. 17, is located on the front of the drill press head. T o turn the drill press “ON” move the switch to the up position. T o tur n the drill press “OFF” move the switch to the down position.
3. The table can be tilted right or left by pulling out and removing table alignment pin (C) Fig. 20, and loosening table lock- ing bolt (D). NOTE: If pin (C) is difficult to r emove, tur n nut (E) clock- wise to pull pin out of casting. Tilt table to the desired angle and tighten bolt (D).
DRILLING HOLES TO DEPTH Where a number of holes ar e to be drilled to exactly the same depth, a depth stop is provided in the pinion shaft housing and is used as follows: 1. Loosen lock screw (A) Fig. 23, and r otate housing (B) until the pointer (C) lines up with the desired depth indicated on scale (D).
OPERA TION Y our drill press is to be used with drill bits of 5/8" or less in diameter . The following directions will give the inexperi- enced operator a start on common drill press operations. Use scrap material for practice to get a feel of the machine before attempting r egular work.
T wo Y ear Limited W arranty Delta Machinery Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be.
Een belangrijk punt na aankoop van elk apparaat Delta 14070 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Delta 14070 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Delta 14070 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Delta 14070 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Delta 14070 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Delta 14070 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Delta 14070 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Delta 14070 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
