Gebruiksaanwijzing /service van het product 17-990X van de fabrikant Delta
Ga naar pagina of 20
INSTRUCTION MANUAL P ART NO. A10354 - 04-06-05 Copyright © 2005 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury .
3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury .
4 GENERAL SAFETY RULES READ AND UNDERST AND ALL W ARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage.
5 SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. ADDITIONAL SPECIFIC SAFETY RULES 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according t o t h e instructions. A machine incorrectly assembled can cause serious injury .
Y ou can have your drill press converted to 230 volt operation. A qualified electrician must perform this conversion. Should you desire to have your drill pr ess converted for 230 volt operation, take your drill press to your local Authorized Delta Service Center .
7 EXTENSION CORDS Use proper extension cor ds. Make sure your extension cor d is in good condition and is a 3-wire extension cord which has a 3-pr ong grounding type plug and matching r eceptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine.
8 1 2 3 4 5 6 7 8 9 10 11A 11B 12 13 14 15 16 17 18 1. Drill Press Head 2. Column and T able Raising Rack 3. T able/Column Bracket 4. Lock Lever for Column Bracket 1/2-13x1-1/2" 5. Lock Lever for T able 3/8-16x1-1/8" 6. W orm for T able-Raising Mechanism 7.
9 ASSEMBL Y ASSEMBL Y TOOLS REQUIRED ASSEMBL Y TIME ESTIMA TE 1. Attach the column (A) Fig. 3 to the base (B) using the four M10x40mm hex head screws (C), thr ee of which are shown. Loosely thr ead the locking lever (D) into the table mounting bracket (E).
10 5. Re-install the ring (E) Fig. 9 (removed in STEP 1) . IMPORT ANT : DO NOT push the ring (E) Fig. 9 all the way down on the the raising rack (F). Make certain that the top of the raising rack (F) is under the bottom of the ring (E) and that enough clearance is available to allow the rack (F) to rotate ar ound the column.
11 IMPORT ANT : Make certain that the spindle taper (Q) Fig. 16 and the tapered hole in the chuck (R) are clean and fr ee of any grease, lacquer , or rust-preventive coatings. NOTE: Household oven cleaner can effectively r emove any substance from the spindle and chuck.
12 5. Thread the two speed-changing levers (W) Fig. 22 into the speed changing hub. 6. Thread the speed range-changing lever (X) Fig. 23 into the hub. Fig.
13 LOCKING SWITCH IN THE “OFF” POSITION IMPORT ANT : When the machine is not in use, the switch should be locked in the “OFF” position to prevent unauthorized use, using a padlock (C) Fig. 28 with a 3/16" diameter shackle. In the event of a power outage, always lock switch in “OFF” position until the main power is restor ed.
1. Insert the bit into the chuck. 2. Lower the chuck (C) Fig. 34, and the drill bit to your chosen depth by rotating the pinion shaft handles (D). Lock the quill in position by tightening the quill locking lever (E). NOTE: The quill locking lever (E) is spring-loaded.
15 ADJUSTING THE SPINDLE RETURN SPRING The spindle will automatically return slowly to its upper position when the handle is released. The spindle r eturn spring was properly adjusted at the factory . However , to adjust, if necessary: 1. Loosen the nuts (B) and (E) Fig.
16 Fig. 39 A B D C NOTE: Use drill bits with a shank of 1/2" or less in diameter . DISCONNECT MACHINE FROM POWER SOURCE . 1. Insert the smooth end of drill bit (A) Fig. 39 in the chuck (B) as far as it will go, and then back the bit out 1/16" (or up to the flutes for small bits).
17 MAINTENANCE TROUBLESHOOTING For assistance with your machine, visit our website at www .deltamachinery .com for a list of service centers or call the DEL T A Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582). LUBRICA TION Oil the variable speed pulleys and the speed range shifter mechanism weekly .
18 P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations.
19 T wo Y ear Limited New Product W arranty Delta will repair or r eplace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven to.
The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.
Een belangrijk punt na aankoop van elk apparaat Delta 17-990X (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Delta 17-990X heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Delta 17-990X vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Delta 17-990X leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Delta 17-990X krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Delta 17-990X bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Delta 17-990X kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Delta 17-990X . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
