Gebruiksaanwijzing /service van het product 36-070 van de fabrikant Delta
Ga naar pagina of 21
INSTRUCTION MANUAL 10" Power Miter Saw (Model 36-070) P ART NO. 899880 (0012) Copyright © 2000 Delta Machinery ESP AÑOL: PÁGINA 21 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 SAFETY RULES W oodworking can be dangerous if safe and proper operating pr ocedures ar e not followed. As with all machinery , there ar e certain hazards involved with the operation of the pr oduct. Using the machine with respect and caution will considerably lessen the possi- bility of personal injury .
3 3 ADDITIONAL SAFETY RULES FOR MITER SA WS 1. USE ONL Y CROSS-CUTTING SAW BLADES. WHEN USING CARBIDE-TIPPED BLADES, MAKE SURE THEY HA VE A NEGA TIVE HOOK ANGLE.
4 4 UNP ACKING 1. Remove the miter saw and all loose items from the carton. IMPORT ANT : DO NOT LIFT THE MITER SAW BY THE SWITCH HANDLE AS THIS MA Y CAUSE MIS- ALIGNMENT . AL WA YS LIFT THE MACHINE BY THE BASE OR CARR YING HANDLE. Fig. 2, illustrates the machine and all loose items after they have been removed fr om the carton.
5 5 ASSEMBLING T ABLE LOCK HANDLE 1. Thread table lock handle (A) Fig. 5, into the thr ead- ed hole (B) of the arm bracket. ROT A TING T ABLE TO 90 DEGREE POSITION 1. Loosen table lock handle (A) Fig. 6, one or two turns and depress index lever (B) to r elease 45 degree positive stop.
6 CONNECTING SA W TO POWER SOURCE POWER CONNECTIONS A separate electrical circuit should be used for your tools. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse.
7 7 7 Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wir e extension cord which has a 3-prong gr ounding type plug and a 3-pole receptacle which will accept the tool’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the saw .
8 8 8 ST AR TING AND STOPPING MACHINE T o start the machine, depress switch trigger (A) Fig. 12. T o stop the machine, release the switch trigger . This miter saw is equipped with an automatic electric blade brake. As soon as the switch trigger (A) Fig.
9 9 9 Fig. 16 LOCKING CUTTINGHEAD IN THE DOWN POSITION When transporting the miter saw , the cuttinghead should always be locked in the down position. This can be accomplished by lowering the cuttinghead (A) Fig. 16, and pushing pin (B) until other end of pin (B) engages with hole in cutting arm.
10 ADJUSTING BLADE P ARALLEL TO T ABLE OPENING 1. DISCONNECT THE SAW FROM THE POWER SOURCE. 2. Lower the cuttinghead and check to see if the saw blade (A) Fig. 20, is parallel to the left edge (B) of the table opening. 3. If an adjustment is necessary , loosen two scr ews, one of which is shown at (C) Fig.
11 11 11 1. An ideal accessory for use with your miter saw is the 36-221 W ork Clamp, shown at (A) Fig. 24. 2. T wo holes (B) Fig. 25, are provided in the base of the miter saw enabling you to use the clamp (A) on either the right or left hand side of the saw blade.
12 1. Y our miter saw has the capacity to cut standard 2 x 4’ s laying flat or on edge, at the 45 degr ee right and left miter angles as shown in Figs. 26 and 27. 2. A standard 2 x 6 can easily be cut in the 90 degr ee straight cut-off position in one pass, as shown in Fig.
13 13 13 4. Cutting various sizes of plastic pipe is an easy job with the miter saw , as shown in Fig. 30. CUTTING ALUMINUM Aluminum extrusions such as used for making aluminum screens and storm windows can easily be cut with your miter saw .
14 1. There ar e several methods that can be used to cut crown mouldings on the miter saw . The method shown in Fig. 35, illustrates the contact surfaces (the surfaces that contact the wall and ceiling) of the crown moulding held firmly against the fence and table of the miter saw .
15 15 5. Fasten the filler blocks to the fence using wood screws (A) thr ough the two holes provided on each fence half, as shown in Fig. 40. This enables you to eas- ily remove the filler blocks when not in use and quickly reassemble them to the fence when needed.
16 CHANGING THE BLADE WARNING: USE ONL Y CROSS-CUTTING SAW BLADES. WHEN USING CARBIDE TIPPED BLADES, MAKE SURE THEY HA VE A NEGA TIVE HOOK ANGLE. DO NOT USE BLADES WITH DEEP GULLETS AS THEY CAN DEFLECT AND CONT ACT THE GUARD. USE ONL Y 10" DIAMETER SAW BLADES WHICH ARE RA TED FOR 6000 RPM OR HIGHER AND HA VE 5/8" DIAMETER ARBOR HOLES.
17 17 17 BRUSH INSPECTION AND REPLACEMENT CAUTION: BEFORE INSPECTING THE BRUSHES, DISCONNECT THE MACHINE FROM THE POWER SOURCE. Brush life varies. It depends on the load on the motor . Check the brushes after the first 50 hours of use for a new machine or after a new set of brushes has been installed.
18 18 18 NOTES.
19 19 19 NOTES.
20 20 Delta Building T rades and Home Shop Machinery T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory.
The following are trademarks of POR TER-CABLE DEL T A Corporation (Las siguientes son marcas r egistradas de PORTER-CABLE S.A.): BAMMER ® , INNOV A TION THA T WORKS ® , JETSTREAM ® , LASERLOC .
Een belangrijk punt na aankoop van elk apparaat Delta 36-070 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Delta 36-070 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Delta 36-070 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Delta 36-070 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Delta 36-070 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Delta 36-070 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Delta 36-070 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Delta 36-070 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
