Gebruiksaanwijzing /service van het product DP400 van de fabrikant Delta
Ga naar pagina of 21
INSTRUCTION MANUAL 16½" Floor Model Drill Pr ess (Model DP400) P ART NO. 907453 - 04-13-04 Copyright © 2004 Delta Machinery ESP AÑOL: PÁGINA 21 T o learn more about DEL T A MACHINER Y visit our website at: www .
2 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury .
3 GENERAL SAFETY RULES 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly minimize the possibility of accidents and injury . 2. WEAR EYE PROTECTION.
4 ADDITIONAL SAFETY RULES FOR FOR DRILL PRESSES 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according t o the instructions.
5 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cords which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug.
6 Fig. C GROUNDED OUTLET BOX CURRENT CARR YING PRONGS GROUNDING BLADE IS LONGEST OF THE 3 BLADES EXTENSION CORDS FOREWORD Delta ShopMaster DP400 is a 16½" drill press with a 120/240 V , 3/4 H.P . induction motor , a flexible work lamp and a tilting table with c-clamp edges and diagonal slots.
7 UNP ACKING AND CLEANING Carefully unpack the machine and all loose items fr om the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened wi th ke r osene (do not use acetone, gasoline or lacquer thinner for this purpose).
8 ASSEMBL Y FOR YOUR OWN SAFETY , DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETEL Y ASSEMBLED AND YOU READ AND UNDERST AND THE ENTIRE INSTRUCTION MANUAL. Fig. 4 Fig. 5 3" MINIMUM 3" MINIMUM 3" MINIMUM 3" MINIMUM 28" MINIMUM 21" MINIMUM C 1.
9 6. Assemble the column (A) Fig. 6, to the base (B) using the four M10x40mm hex head screws (C), thr ee of which are shown. Fig. 6 7. Assemble table raising and lowering handle (D) Fig. 7, to worm gear shaft (E) and tighten screw (F) against flat on shaft with 3mm wrench supplied.
10 Fig. 9 9. Insert table (H) Fig. 9, into hole in table bracket as shown. Fig. 10 10. Thread table locking lever (J) Fig. 10, into hole in front of table bracket as shown. Fig. 11 Fig. 12 11. Place the drill press head (K) Fig. 11, onto the column as far as it will go.
11 Fig. 14 14. IMPORT ANT : Make certain the spindle taper (O) Fig. 14, and tapered hole in chuck (P) ar e clean and free of any grease, lacquer or rust pr eventive coatings. NOTE: Household oven cleaner can effectively r emove any sub- stance from the chuck; however , carefully follow the manufacturer's safety rules concerning its use.
12 18. Align the two holes in the lamp bracket (A) Fig. 17, with the two holes (B) on the side of the drill press head. Fig. 17 20. Align the two holes in the lamp cord bracket (F) Fig. 18 with the two holes in the lamp bracket (A) and drill press head.
13 OPERA TING CONTROLS AND ADJUSTMENTS ST AR TING AND STOPPING DRILL PRESS The switch (A) Fig. 20, is located on the front of the drill press head. T o turn the drill press “ON” move the switch up to the “ON” position. T o tur n the drill press “OFF” move the switch down to the “OFF” position.
14 Fig. 24 C E 3. The table can be tilted right or left by pulling out and removing table alignment pin (C) Fig. 24. NOTE: If pin (C) is difficult to r emove, tur n nut (E) clockwise to pull pin out of casting. 4. Fig. 25, illustrates the table alignment pin (C) removed.
15 SPINDLE SPEEDS T welve spindle speeds are available on the drill press. Fig. 27, illustrates which steps of the pulleys the belts must be placed to obtain the twelve speeds available.
16 DRILLING HOLES TO DEPTH Where a number of holes ar e to be drilled to exactly the same depth, a depth stop is provided and is used as follows: DISCONNECT MACHINE FROM POWER SOURCE.
17 OPERA TIONS Fig. 32 Y our drill press is to be used with drill bits with a shank of 5/8" or less in diameter . The following will give the inexperi enced operator a start on common drill press operations. Use scrap material for practice to get a feel of the machine before attempting r egular work.
18 BORING IN WOOD T wist drills, although intended for metal drilling, may also be used for boring holes in wood. However , machine spur bits are generally pr eferred for working in wood; they cut a flat bottom hole and are designed for r emoval of wood chips.
19 NOTES.
20 P AR TS, SERVICE OR W ARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and are serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations.
The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de PORTER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.
Een belangrijk punt na aankoop van elk apparaat Delta DP400 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Delta DP400 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Delta DP400 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Delta DP400 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Delta DP400 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Delta DP400 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Delta DP400 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Delta DP400 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
