Gebruiksaanwijzing /service van het product ANAS550 van de fabrikant Airlink101
Ga naar pagina of 41
2-Bay NAS 3.5” SATA Network Attached Storage Model # ANAS550 User’s Manual Ver. 1.0.
2 Table of Contents 1. Intr oducti on ................................................................................................................ .......... 3 1.1 Package Content s .................................................................
3 1. Introduction Thank you for purchasing Airlink101 2-Bay 3. 5” SATA Network Attached Storage (NAS). This product provides two 3.5” SATA hard disk drives (not included in the package), allowing you to build a mass storage center for backing up y our valued data.
4 • Automatic E-mail Alert system • Support UPnP AV Server for windows XP • Support NTP Server for syst em time synchronization 1.3 LED Indicators 1. Power LED – The steady Blue light indic a tes the server is powered on. This LED will be off when the 2-Bay NAS is on power saving mode.
5 2. Inst alling 2-Bay NAS 2.1 Installing Hard Drive(s) This section provides instructions on how to pr operly install a hard drive into the NAS device. WARNING: The 2-Bay NAS is not hot-swappable. Please make sure that it is turned off and not connected to the power outlet when perfo rming the following assembly procedure.
6 Step 4 Replace the front panel onto the server. Step 5 Plug an Ethernet cable to the LAN port locat ed on the rear panel, and then connect it to your switch or router. Step 6 Plug the AC power adapter to the power connector located on the rear panel, and connect it to a power outlet.
7 2.2 Configuring 2-Bay NAS Before using the NAS device you may need to do some configuration which can be accessed in a few different ways. Step 1 Connect to the web configurat ion page of the 2-Bay NAS. There are multiple methods to access the NAS configuration.
8 Step A3 Double click the icon on your desktop or go to Start > (All) Programs > Airlink101> Airlink101 2-Bay NAS Utility . Step A4 Select the NAS device you want to connect to and click on .
9 Method B: Using your web browser (I nternet Explorer or Firefox) To use your web browser, open up the browser and in the Address bar type in http://anas550 and press Enter or hit the Go button. Step 2 When prompted for a username and password, type in admin for the username and admin for the password in lowercase letters.
10 Step 4 Select a RAID type you want to use and click Next . Note: All data will be lost if you want to change the RAID type in the future. Step 5 Click OK to start formatting y our hard drive(s). Warning: All data will be erased fr om the hard drive(s).
11 2.3 Accessing 2-Bay NAS There are several ways to access the 2-Bay NAS. Method 1: Using the host name “ANAS550”. Step 1 To access 2-Bay NAS, go to Start > Run , and type in anas550 and click OK . Step 2 Click on the Volume_1 folder to begin accessing your files and using 2-Bay NAS to store/backup your data.
12 Step 2 When the setup wizard comes up, fo llow the screen instructions and click Next to finish installing the 2-Bay NAS Utility. To open the 2-Bay NAS Utilit y, double click the icon on your desktop or go to Start > (All) Programs > Airlink101 > Airlink101 2-Bay NAS Utility.
13 Step 3 Select the NAS device under Search Device box and the disk drive you try to mount to your computer from Static box, and click Mount . Then, you will be able to access the disk drive from My Computer.
14 Note: If you have installed 2 hard drives, you wil l see both of them only when you configure the RAID type as “Standard” mode. Please refer back to 2.
15 3. Using W eb Configuration You can access and manage the 2-Bay NAS through a web browser. This chapter provides you with instructions of how to use the Web Configur ation, and explains how to set up your 2- Bay NAS with the web browser.
16 Step 2 You are recommended to set an admin passw ord here. Enter the new password and re-enter it for confirmati on. When completed, click Next ..
17 Step 3 For system management purpose, a correct time setting is critical to have accurate time stamps on the system logs . Set an appropriate Time Zone in this step. When completed, click Next . Step 4 You can select the connection type and enter the LAN information, or keep the current settings.
18 Step 5 Enter a workgroup, name, and description fo r the 2-Bay NAS, or leave the default values. When completed, click Next . Step 6 When completed, click Restart to restart the 2-Bay NAS a nd save the configuration, or click Back to go back the previous steps and change the settings.
19 SETUP – LAN The Local Area Network settings for the 2-Ba y NAS are configured on the LAN page. Click Save Settings to save the configuration you make. • Link Speed: The LAN speed is set to Auto by default, but can be manually set to 100 or 1000 Mbps.
20 • Workgroup: Assign a workgroup name to the 2-Bay NAS. • Name: Assign a name to the 2-Bay NAS so t hat you can access it through a web browser by entering the device name. For example, http://anas550 . When completed, click Save Settings to save the settings.
21 3.2 ADVANCED ADVANCED – USER The 2-Bay NAS supports up to 64 users. The users can be s pecified by group or created individually. The created users are allowed to a ccess the specific folders on the NAS server via FTP or the local network.
22 ADVANCED – GROUP The 2-Bay NAS supports up to 10 groups. To manage the NAS server easily and efficiently, the users can be assigned to groups. You can se t up the access rules and quotas for each group. • User And Group Creation: Select Group and enter a unique group name in the blank of Add New Group .
23 ADVANCED – QUOTAS The 2-Bay NAS supports the quot a feature for both group and i ndividual users so that you can limit the amount of storage they are allocated. By defaul t, users and groups do not have a quota. • User Quota Settings: User quotas are displayed her e.
24 • Network Access Settings: Assign permissions for the users and groups on the local network here. o Category: Select Group or User to decide the access rule. o Group/User: Select the group or user the access rule will apply to. o Folder: Click Browse to select the folder or direct ory.
25 ADVANCED – FTP SERVER The 2-Bay NAS is equipped with a built-in user-f riendly FTP server, which allows the users to access the important data whether they are on the local network or at a remote location. In addition, the FTP server can be configured to allow up to 10 users to access different directories simultaneously on the 2-Bay NAS.
26 o Max User: Set the maximum amount of user s that can connect to the FTP server. o Idle Time: Set the amount of time a user can remain idle before being disconnected. o Port: Set the FTP port. Default is 21 . o Flow Control Path: Allow you to limit the amount of bandwidth available for each user.
27 be automatically detected in the iTunes program and the music and videos contained in the specified directory will be available to stream over the network. • iTunes Server: Select Enable or Disable for the function. • Folder: Specify the folder or directory that will be shared by the iTunes server.
28 • DHCP Server: Select Enable or Disable for the function. o Starting IP Address: Enter the starting IP address for the range of addresses assigned by the DHCP server. o Ending IP Address: Enter the ending IP addre ss for the range of addresses assigned by the DHCP server.
29 3.3 TOOLS TOOLS – ADMIN This page allows you to set a password for the admin account. It is recommended to set an administrator password when firs t configuring the 2-Bay NAS. • User Name: The administrator user name is admin , and this cannot be changed.
30 • NTP Server: Network Time Protocol (NTP) synch ronizes your 2-Bay NAS with an Internet time server. Enter t he IP Address or domain name of the time server you want to sync the 2-Bay NAS and click Set Time. • From My Computer: Click Set Time to sync your clock on 2-Bay NAS with the computer being used to configure it.
31 • Restart: Click Restart to reboot the 2-Bay NAS. • Defaults: Click Restore to reset the 2-Bay NAS to t he factory default settings. This will erase all previous configuration changes. • Configuration Settings: Click Save to save the current settings to a file on the local computer.
32 • Current Firmware Info: This section shows the information about the current firmware version of the 2-Bay NAS. To upgrade the firmware, click Browse to select the new firmware file on your local computer and then click Apply to begin the firmware upgrade process.
33 • E-mail Alert Settings: This section contains the se ttings for the outgoing e-mail account and the receiving e-mail account. Once configured, use the Test E-Mail button to send a test e-mail and c onfirm your settings are correct. o Login Method: Select Account or Anonymous .
34 When completed, click Save Settings to save the settings. TOOLS – RAID The 2-Bay NAS supports four di fferent disk configuration types: Standard , JBOD , RAID 0 and RAID 1 . RAID Settings: Click Set RAID Type and Re-Format to change the current drive configuration.
35 3.4 STATUS DEVICE INFO This page displays the general in formation of the 2-Bay NAS. • LAN Info: Displays the local network settings of the 2-Bay NAS. • Device Info: Displays the workgroup, device name, device description and current temperature of the 2-Bay NAS.
36 3.5 SUPPORT This page provides a menu of S upport topics explaining the feat ures of the 2-Bay NAS. Click on the desired link to display the related online instruction.
37 4. Downloading/Backing up Files Through 2-Bay NAS This section will describe one of the built in features of 2-Bay NAS to automatically download files via either FTP or HTTP directly to t he NAS storage by itself without using a computer.
38 4.1 Scheduling This page allows you to setup your downloa d tasks on the 2-Bay NAS. Enter the required information in the relative fields. • Scheduling Settings: Configure download and backup schedules here. o Login Method: According to the settings of target server, choose Account or Anonymous .
39 have the 2-Bay NAS compare identical file names at the source and destinat ion. Files will only be overwritten if th e source file is more recent. • Schedule List: This section displays all complet ed, active and pending scheduled downloads and backups.
40 5. S pecifications Standards Compliance • IEEE 802.3 • IEEE 802.3u • IEEE 802.3ab Hard Drive Type • 3.5” SATA or SATA II hard drives File Type • EXT2 Interface • 1 x 10/100/1000 Mbps .
41 T echnical Support E-mail: support@airlink101.com Toll Free: 1-888-746-3238 Web Site: www.airlink101.com * Actual data throughput will var y . Network conditions and en viro nmenta l factors lower actual data throughput rate. Specifications are subject to change without notice.
Een belangrijk punt na aankoop van elk apparaat Airlink101 ANAS550 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Airlink101 ANAS550 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Airlink101 ANAS550 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Airlink101 ANAS550 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Airlink101 ANAS550 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Airlink101 ANAS550 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Airlink101 ANAS550 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Airlink101 ANAS550 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
