Gebruiksaanwijzing /service van het product MG7-OFTWIN van de fabrikant DeVillbiss Air Power Company
Ga naar pagina of 16
DeVilbiss Air Power Company • 213 Industrial Drive • Jackson, TN 38301-9615 MG7-OFTWIN REV. 11/5/98 SAFETY GUIDELINES ....................................................... 1 WARRANTY STATEMENT ................................................. 2 WARNING CHART .
2 — ENG ❏ Retain original cash register sales receipt as proof of purchase for warranty work. ❏ Use reasonable care in the operation and maintenance of the product as described in the Owners Manual(s). ❏ Deliver or ship the product to the nearest DeVilbiss Air Power Authorized Warranty Service Center.
3 — ENG RISK OF BURSTING RISK OF EXPLOSION OR FIRE RISK OF ELECTRICAL SHOCK AIR TANK THE FOLLOWING CONDITIONS COULD LEAD TO A WEAKENING OF THE TANK, AND RESULT IN A VIOLENT TANK EXPLOSION: 1. FAILURE TO PROPERLY DRAIN CONDENSED WATER FROM THE TANK, CAUSING RUST AND THINNING OF THE STEEL TANK.
4 — ENG HAZARD RISK OF ELECTRICAL SHOCK (cont’d) RISK FROM FLYING OBJECTS RISK TO BREATHING RISK OF FALLING RISK FROM MOVING PARTS RISK OF BURNS WHAT CAN HAPPEN REPAIRS ATTEMPTED BY UNQUALIFIED PER- SONNEL CAN RESULT IN SERIOUS INJURY OR DEATH BY ELECTROCUTION.
5 — ENG DAMAGE : Each air compressor outfit is carefully tested and checked before shipment. With improper handling, damage may result in transit and cause problems in compressor operation. Immediately upon arrival, check equipment for both concealed and visible damages to avoid expenses being incurred to correct such problems.
6 — ENG DESCRIPTION OF OPERA TION It may be necessary to brace or support one end of the outfit when attaching the wheels and the rubber foot strip because the air compressor will have a tendency to tip.
7 — ENG It may be necessary to brace or support one side of the outfit when removing the shipping boards be- cause the air compressor will have a tendency to tip. 1. Remove all packaging such that only the compressor on the pallet remains. Remove and discard the (4) screws and washers that hold the compressor to the pallet.
8 — ENG Additional Regulators and Controls Since the air tank pressure is usually greater than that which is needed, a separate regulator is usually employed to control the air pressure ahead of any individual air driven device. Break-in Procedures Serious damage may result if the following break- in instructions are not closely followed.
9 — ENG INSTALLATION AND BREAK-IN PROCEDURES (cont'd) RISK OF ELECTRICAL SHOCK. IMPROPER ELECTRICAL GROUNDING CAN RESULT IN ELECTRICAL SHOCK. WIRING FOR THIS UNIT SHOULD BE DONE BY A LICENSED ELECTRI- CIAN IN ACCORDANCE WITH NATIONAL AND LOCAL CODES AND ORDINANCES.
10 — ENG Air Filter - Inspection and Replacement Keep the air filter clean at all times. Do not operate the compressor with the air filter removed. A dirty air filter will not allow the compressor to operate at full capacity. Before you use the compressor, check the air filter to be sure it is clean.
11 — ENG 2. Protect the electrical cord and air hose from damage (such as being stepped on or run over). Wind them loosely around the compressor handle. 3. Store the air compressor in a clean and dry location. Before you store the air compressor, make sure you do the following: 1.
12 — ENG PROBLEM CAUSE Move the pressure switch lever to the “OFF” posi- tion. If the outfit doesn’t shut off, unplug. If the electrical contacts are welded together, replace the pressure switch. Contact an authorized service center to check and replace pressure switch.
13 — ENG PROBLEM CAUSE CORRECTION Motor overload protection switch has tripped. Tank pressure exceeds pressure switch “cut-in” pressure. Wrong gauge wire or length of exten- sion cord. Check valve stuck open. Loose electrical connections. Possible defective motor or capacitor.
14 — ENG SERVICE NOTES NOT AS DE SER VICIO NOTES SUR LE SERVICE.
15 — ENG SERVICE NOTES NOT AS DE SER VICIO NOTES SUR LE SERVICE.
DeVilbiss Air Power Company • 213 Industrial Drive • Jackson, TN 38301-9615 GENERAL MANUAL FOR PERMANENTL Y LUBRICA TED TWIN CYLINDER AIR COMPRESSORS SERVICE NOTES.
Een belangrijk punt na aankoop van elk apparaat DeVillbiss Air Power Company MG7-OFTWIN (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen DeVillbiss Air Power Company MG7-OFTWIN heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens DeVillbiss Air Power Company MG7-OFTWIN vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding DeVillbiss Air Power Company MG7-OFTWIN leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over DeVillbiss Air Power Company MG7-OFTWIN krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van DeVillbiss Air Power Company MG7-OFTWIN bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de DeVillbiss Air Power Company MG7-OFTWIN kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met DeVillbiss Air Power Company MG7-OFTWIN . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
