Gebruiksaanwijzing /service van het product WN-150CAM van de fabrikant AirLive
Ga naar pagina of 76
. AirCam WN-150CAM/ I P - 1 5 0 C A M W ir eless N 150Mbps Dual Stream IP Camer a / F ast Ether net Dual Str eam IP Camera User’ s Manual.
Copyright & Disclaimer 1 AirCam WN-150CAM/IP-150CAM Use r’s Manual Copyright Copyright ©2010/201 1 by this company . A ll rights reserved. No p art of this publication may be reproduced, transm.
Copyright & Disclaimer AirCam WN-150CAM/IP-150CAM User ’ s Manual 2 Europe – EU Declaration of Conformity These devices compile with the essentia l requirements of the R&TTE Directive 1999/5/EC.
Copyright & Disclaimer 3 AirCam WN-150CAM/IP-150CAM Use r’s Manual This device complies with Part 15 of the FC C Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interf erence received, including interference that may cause undesired operation.
T able of Content s i AirCam WN-150CAM/IP-150CAM User ’s Manual T able of Content s 1. Product Overview .................................................................................... 1 1.1. Introduction ........................................
T able of Content s AirCam WN-150CAM/IP-150CAM User ’ s Manual ii 5.2.1. General ......................................................................................... 28 5.2.2. MPEG4 ..............................................................
1. Product Overview 1 AirCam WN-150CAM/IP-150CAM Use r’s Manual 1 1. Product Overview 1.1. Introduction The IP-150CAM/WN-150CAM is an ultra-compact IP Camera equipped with a high sensitivity progressive scan CMOS sensor , achieving high image quality and superior low-light performance.
1. Product Overview AirCam WN-150CAM/IP-150CAM User ’ s Manual 2 - Two-way Audio with Built-In Microphone - Support Mac OS - Support iPhone - Support Live Video Viewing on Windows Live Messenger - Mobile Phone Streaming Live Video through 3GPP / ISMA / RTSP - Mobile Phone Live Image through 2.
1. Product Overview 3 AirCam WN-150CAM/IP-150CAM Use r’s Manual 1.2. Basic Connection y Wired Connection 1. Connect the power adaptor to IP Camera. 2. Connect IP Camera’ Ethernet port to your Hub / Switch / Router. y Wireless Connection (Only WN-150CAM) 1.
1. Product Overview AirCam WN-150CAM/IP-150CAM User ’ s Manual 4 1.3. Application.
2. Hardware Inst allation 1 AirCam WN-150CAM/IP-150CAM Use r’s Manual 2.1. Safety Instruction 2 2. Hardware Inst allation y Before you use this product This product has been designed with safety in mind. However, the electrical products can cause fires which may lead to serious body injury if not used properly.
2. Hardware Inst allation AirCam WN-150CAM/IP-150CAM User ’ s Manual 2 y Operation Notice - Operating or storage location Avoid operating or st oring the camera in the following locations: - Extreme.
2. Hardware Inst allation 3 AirCam WN-150CAM/IP-150CAM Use r’s Manual y Ventilation To prevent heat buildup, do not block air circulation around the device.
2. Hardware Inst allation AirCam WN-150CAM/IP-150CAM User ’ s Manual 4 3. Please always update the latest Windows component. (Net Framework, Windows Media Player, Enhance ActiveX Security) 2.
2. Hardware Inst allation 5 AirCam WN-150CAM/IP-150CAM Use r’s Manual 2.4. Physical Description 2.4.1. Front View y Focus Adjustment Ring - Adjust focus manually to achieve the best image quality. y Power LED indicator - Power LED will light up after the IP Camera completed the boot process.
2. Hardware Inst allation AirCam WN-150CAM/IP-150CAM User ’ s Manual 6 POWER LED D Steady Red Boot up process Steady Blue Boot up complete Steady Blue → Flash Purple Push WPS button and ready for .
2. Hardware Inst allation 7 AirCam WN-150CAM/IP-150CAM Use r’s Manual y Power Connector - For connection of 12V DC input. y Reset – When the device is empowered, press the Reset Button to reboot the device, or hold the Reset Button for 10 seconds to set the device settings back to factory default.
2. Hardware Inst allation AirCam WN-150CAM/IP-150CAM User ’ s Manual 8 y Power and Ethernet Connecting 1. Use a standard RJ-45 network cable to connect the IP Camera to the Network connection 2.
3. Easy Acce ss 9 AirCam WN-150CAM/IP-150CAM Use r’s Manual 3 3. Easy Access 3.1. W eb Browsers 3.1.1. W indows Web Browsers 1. S t art your web browser , and enter the IP address or host name of the IP camera in the Location / Address field of your browser .
3. Easy Access AirCam WN-150CAM/IP-150CAM User ’ s Manual 10 3. The monitor image will be displayed in y our browser . In the far lef t side of main configuration are Setting, Client Setting, and Image Setup. 3.1.2. Mac Safari 1. Click the Safari icon, and enter the IP address of the IP camera in the Location / Address field of your browser .
3. Easy Acce ss 11 AirCam WN-150CAM/IP-150CAM User ’s Manual 2. Use the default login name “adm in” and default password “airlive”. Note The default user name “admin” and the pa ssword a.
3. Easy Access AirCam WN-150CAM/IP-150CAM User ’ s Manual 12 4. The monitor image will be displayed in y our browser . In the far lef t side of main configuration are Setting, Client Setting, and Image Setup.
3. Easy Acce ss 13 AirCam WN-150CAM/IP-150CAM User ’s Manual 3.2. Mobile Phone V iewing 3.2.1. Using IP Camera via iPhone Y ou can use AirLive Web User Interface via iPhone. Please follow the setting process below . Then, you can us e AirLive web UI via iPhone.
3. Easy Access AirCam WN-150CAM/IP-150CAM User ’ s Manual 14 3.2.2. 3G Mobile Phone S treaming For 3G mobile phone viewing, type “ rtsp://<IP>:<POR T>/video.3gp ” into your 3G S t reaming Link. <IP> is the Public IP addr ess of yo ur IP came ra; <PORT> is the R TSP port of your IP camera (Default value is 554.
3. Easy Acce ss 15 AirCam WN-150CAM/IP-150CAM User ’s Manual 3.2.4. 2.5G Mobile Phone Browser For 2.5G mobile phone viewing, type “ http://<IP>/m obile.wml ” into your 2.5G W AP Browser . <IP> is the Public IP addr ess of your IP camera.
3. Easy Access AirCam WN-150CAM/IP-150CAM User ’ s Manual 16 4. Y ou will get IP information automatically 5. Click to live viewing by Windows Live Messenger 6.
3. Easy Acce ss 17 AirCam WN-150CAM/IP-150CAM User ’s Manual 7. Click icons to snapshot or optimize image.
4. Live View AirCam WN-150CAM/IP-150CAM User ’ s Manual 18 4 4. Live V iew 4.1. Live V iew Control Panel.
4. Live View 19 AirCam WN-150CAM/IP-150CAM User ’s Manual 4.2. Setting This function is only for the Administra tor . Click this butto n to get into the setting page. There are four sub-folders including System, Camera, Network, and Events and a Question mark inside.
4. Live View AirCam WN-150CAM/IP-150CAM User ’ s Manual 20 HELP is an online help and support. It provides solutions immediately..
4. Live View 21 AirCam WN-150CAM/IP-150CAM User ’s Manual 4.3. Client Setting This function is only for the administrator and client. y Mode Click the pull-down box to choose between MPEG-4 MJPEG, and JPEG video compression mode. MJPEG streaming is unavailable if RTSP mode is “On.
4. Live View AirCam WN-150CAM/IP-150CAM User ’ s Manual 22 4.4. Image Setup y Brightness The higher value the brightness is, the brighter the image is. y Contrast The contrast is a measure of a display system, defined as the ratio of white to black that the system is capable of producing.
5. Setting 23 AirCam WN-150CAM/IP-150CAM User ’s Manual 5 5. Setting 5.1. System 5.1.1. Information The Information page provides the produc t factory information which includes Product Name, Firmware V ersion and Web V ersion .
5. Setting AirCam WN-150CAM/IP-150CAM User ’ s Manual 24 y Current date / time Display the current date and time of this IP Camera. y PC clock Display the date and time of the monitoring PC clock. y Date / T ime format Pull down box to select diffe rent time display forma ts.
5. Setting 25 AirCam WN-150CAM/IP-150CAM User ’s Manual 5.1.3. Account The device fault account and password setti ng is “admin / admin”. That means everyone who knows IP address can access the device including all configuration. It is necessary to assign a p assword if the device is intended to be accessed by others.
5. Setting AirCam WN-150CAM/IP-150CAM User ’ s Manual 26 - Operator mode View the Live View and Use Control Panel. - Viewer mode View the Live View only. y V iew er Authentication Allows any viewer direct access to Live View. 5.1.4. System Log The System Log function allows users to review any changes and events happened.
5. Setting 27 AirCam WN-150CAM/IP-150CAM User ’s Manual 5.1.5. Initialize y Reboot Reboot this IP Camera and it takes two minutes to reboot this IP Camera. y Factory Default Reset this IP Camera to the factory default setting. Don't turn off this IP Camera until the device reboots.
5. Setting AirCam WN-150CAM/IP-150CAM User ’ s Manual 28 5.2. Camera 5.2.1. General y RTSP Switch RTSP “On” or “Off.” The default value is 554. y Image Rot ate You can mirror or flip the display screen. y Audio Codec If this option is selected On, the microphone will st art sound reception.
5. Setting 29 AirCam WN-150CAM/IP-150CAM User ’s Manual y White Balance You can choose the white balance to Auto, Florescent, Incandescent and Black & White. y LED Indicator Turn on/off the LED indicator. y Overlay - Text Overlay You can see some information on the display screen which includes Date / Time and user-defined text.
5. Setting AirCam WN-150CAM/IP-150CAM User ’ s Manual 30 y V iew er Authentication If the viewer authentication is On, t he users will be requ ested to key-in username and password when viewing through RTSP. y Multicast Streaming (If it’ s on) - Multicast Address Specify the multicast server address.
5. Setting 31 AirCam WN-150CAM/IP-150CAM User ’s Manual y Quality - Auto The quality and bitrate will be adjusted automatically according to the frame rate. - Fixed Quality You can select the value of quality. - Fixed Bitrate Set the bitrate of MPEG4 image transmission for a line.
5. Setting AirCam WN-150CAM/IP-150CAM User ’ s Manual 32 y V iew er Authentication If the viewer authentication is On, t he users will be requ ested to key-in username and password when viewing through RTSP. y Multicast Streaming (If it’ s on) - Multicast Address Specify the multicast server address.
5. Setting 33 AirCam WN-150CAM/IP-150CAM User ’s Manual 5.2.3. MJPEG If RTSP is OFF , the option of Image Size & Fr ame Rate & Quality will appear . y Image Size Specify the image size when the network camera transmits y Frame Rate Set the frame rate of the MJPEG image.
5. Setting AirCam WN-150CAM/IP-150CAM User ’ s Manual 34 5.3. Network 5.3.1. Information Display the MAC address of the device. y Obt ain an IP address automatically (DHCP) Select this while the IP address is assigned by the DHCP server. y Obt ain DNS server address automatically Select this to obtain the addre ss of DNS server automatically.
5. Setting 35 AirCam WN-150CAM/IP-150CAM User ’s Manual - Default gateway Enter the default gateway. y Use the following DNS server address Select this when you set the fixed address as the IP address of DNS server. - Primary DNS server Enter the IP address of the primary DNS server.
5. Setting AirCam WN-150CAM/IP-150CAM User ’ s Manual 36 Note 1. The IP Camera needs to be rebooted a fter it finishes changing the network completely. 2. The IP Camera with Intelligent IP In staller can’t be founded after turning on the PPPoE and reboot.
5. Setting 37 AirCam WN-150CAM/IP-150CAM User ’s Manual y Server name Choose the DDNS Server from the list. y User ID Enter the user ID for authentication necessary for DDNS connections. Type it up to 64 characters. y Password Enter the password for authentication necessary for DDNS connections.
5. Setting AirCam WN-150CAM/IP-150CAM User ’ s Manual 38 5.3.4. UpnP Y ou can select UPnP function “On” or “O ff”. If a ROUTER is used to access to internet and it supports UPnP IGD func tion, please turn on the UPnP Port Forwarding function.
5. Setting 39 AirCam WN-150CAM/IP-150CAM User ’s Manual 5.3.5. IP Notification When network notify type is set to “ON”, you can send an e-mail notification of the completion of the network setting.
5. Setting AirCam WN-150CAM/IP-150CAM User ’ s Manual 40 y SMTP Select if SMTP authentication is necessary when an e-mail is sent. y POP before SMTP Select if POP before SM TP authentication is necessary when an e-mail is sent. - POP server name Type the POP server name of the user.
5. Setting 41 AirCam WN-150CAM/IP-150CAM User ’s Manual y WPS Enable/disable the WPS function. y Configure via Push button Click “Start.” y Configure via Pin code Password for this msn account. 5.3.7. Wireless The wireless network has to be set up by using cable network connection.
5. Setting AirCam WN-150CAM/IP-150CAM User ’ s Manual 42 1. See the wireless setting page. Then c lick “Refresh”. All access points (AP) around you will show up. 2. Select the AP you wish to connect. 3. Enter password at active transmi t key if you need.
5. Setting 43 AirCam WN-150CAM/IP-150CAM User ’s Manual 6. Connect to the IP camera wit h wireless IP address, and then you can remove the Ethernet connection. 5.3.8. Messenger If Messenger option is selected On, y ou can set out the setting of MSN account.
5. Setting AirCam WN-150CAM/IP-150CAM User ’ s Manual 44 y Alias This alias will display on MSN nickname. y Port range Select one port range for video transmission. y IP Notification Switch the IP notification On / Off. If this feature switches On, camera will send IP notification to the users who are allowed.
5. Setting 45 AirCam WN-150CAM/IP-150CAM User ’s Manual y FTP server name Type the FTP server name to upload still images up to 64 characters, or the IP address of the FTP server. y User name Type the user name for the FTP server. y Password Type the password for the FTP server.
5. Setting AirCam WN-150CAM/IP-150CAM User ’ s Manual 46 5.4.1.2. Alarm sending Set to forward the image file to the specified FTP server linked with the alarm detection by the built-in motion detection function. Select On to send the image file to FTP server linked with the alarm detection.
5. Setting 47 AirCam WN-150CAM/IP-150CAM User ’s Manual - Sequence number The sequence number is added to the Image file name. - Sequence number clear Click Clear and the suffix of the sequence number returns to 1. y Alarm - Motion Detection Click it on for using Motion Detection function as a sensor .
5. Setting AirCam WN-150CAM/IP-150CAM User ’ s Manual 48 y Remote Path Type the path to the destination in FTP. y Image File Name Type the file name you want to assign to the images when sending to the FTP server. Note You can set schedule function at schedule page.
5. Setting 49 AirCam WN-150CAM/IP-150CAM User ’s Manual 5.4.2. SMTP 5.4.2.1. General Y ou can send a mail with attached image file which shot by external sensor input and motion detections or shot periodically . y SMTP Server Name Type the SMTP server name or the IP address y SMTP Server Port Set port number of your mail server.
5. Setting AirCam WN-150CAM/IP-150CAM User ’ s Manual 50 y POP before SMTP Select if POP before SM TP authentication is necessary when an e-mail is sent. - POP server name T ype the POP server name of the user . - User name, Password T ype the user name and Password of the user .
5. Setting 51 AirCam WN-150CAM/IP-150CAM User ’s Manual y File att achment Set whether an image file is attached to the mail sent or not. y Image File Name Type the file name you want to assign to the images when sending to the FTP server. Note 1. You can set motion detecti on at motion detection page.
5. Setting AirCam WN-150CAM/IP-150CAM User ’ s Manual 52 y Effective period Set the period when the periodi cal sending is effective. - Always The periodical sending is always effective. - Schedule Y ou can specify the period when the per iodical sending is effective in the Schedule setting in the other section.
5. Setting 53 AirCam WN-150CAM/IP-150CAM User ’s Manual y Suffix Select a suffix to be added to the file name sent by SMTP. - None The name of the sent file will be the Image file name. - Date & time The date & time suffix is added to the Image file name.
5. Setting AirCam WN-150CAM/IP-150CAM User ’ s Manual 54 y Protocol - Windows Network (SMB/CIFS): - Network Storage Location T ype the IP or name of specified computer and folder . For example, //IP/folder name or // my_nas/folder name. - Workgroup T ype the name of workgroup which the operating com puter belongs.
5. Setting 55 AirCam WN-150CAM/IP-150CAM User ’s Manual - Test After setting the network storage loca tion information, you can tick the test key to test if the connection between IP CAM and network storage location works. 5.4.3.2. Alarm Sending Set to transmit the snapshot or video c lip file with connection to the alarm detection.
5. Setting AirCam WN-150CAM/IP-150CAM User ’ s Manual 56 y Suffix Select a suffix to add to the file name. - Date & time The date & time suffix is added to the Image file name. - Sequence number The sequence number is added to the Image file name.
5. Setting 57 AirCam WN-150CAM/IP-150CAM User ’s Manual y Image file name Type the file name of the image sent by SMTP up to 10 alphanumeric characters, - (hyphen) and _ (under score). y Suffix Select a suffix to be added to the file name sent by SMTP.
5. Setting AirCam WN-150CAM/IP-150CAM User ’ s Manual 58 y Recording T ime Set the period when the periodi cal sending is effective. - Always The periodical sending is always effective. - Schedule Y ou can specify the period when the per iodical sending is effective in the Schedule setting in the other section.
5. Setting 59 AirCam WN-150CAM/IP-150CAM User ’s Manual y Threshold It means the extent which the alarm will be triggered. y Sensitivity It means that how often the sensor will scan the image different. The higher sensitivity it is and the more frequently it scans.
5. Setting AirCam WN-150CAM/IP-150CAM User ’ s Manual 60 - e-Mail (SMTP) -Alarm - e-Mail (SMTP) -Periodical y Mon (Monday) to Sun (Sunday) The time period on the right of the che cked day is the effective period of the schedule. - Start time, End time S pec ify the S t art time and the End time.
5. Setting 61 AirCam WN-150CAM/IP-150CAM User ’s Manual.
6. Appendix AirCam WN-150CAM/IP-150CAM User ’ s Manual 62 6 6. Appendix y Frame Rate and Bitrate T able MPEG4 @ 30fp s / Kbps MPEG4 / Kbp s, fp s MJPEG @ 15fp s / Kbps MJPEG / Kbp s, fp s y S torage.
6. Appendix 63 AirCam WN-150CAM/IP-150CAM User ’s Manual Image-Size Bitrate Setting Frame-Rate Current Current 640*480 2048 30 1800 26 640*480 2048 15 2200 16 640*480 1536 30 1500 30 640*480 1536 15.
6. Appendix AirCam WN-150CAM/IP-150CAM User ’ s Manual 64 y MJPEG / Kbp s, f p s Image-Size Quality Setting Frame-Rate Current Current Frame-Rate 640*480 Excellent 15 4000 13 640*480 Excellent 5 160.
6. Appendix 65 AirCam WN-150CAM/IP-150CAM User ’s Manual y MPEG4 Storage Requirement GB / channel / day @ 15f p s Quality 640*480 320*240 160*120 Excellent 5.3 1.6 0.4 Detailed 2.1 0.8 0.3 Good 1.6 0.6 0.2 Standard 1.3 0.4 0.1 Medium 1.3 0.3 0.1 Image-Size Bitrate Setting Frame-Rate Setting Current Bitrate 640*480 2048 30 23.
6. Appendix AirCam WN-150CAM/IP-150CAM User ’ s Manual 66 y MJPEG Storage Requirement GB / channel / day @ 15f p s Quality 640*480 320*240 160*120 Excellent 42.2 15.8 6.3 Detailed 25.3 9.5 4.2 Good 16.9 6.9 3.2 Standard 13.7 5.3 2.5 Medium 9.5 3.7 1.
Een belangrijk punt na aankoop van elk apparaat AirLive WN-150CAM (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen AirLive WN-150CAM heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens AirLive WN-150CAM vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding AirLive WN-150CAM leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over AirLive WN-150CAM krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van AirLive WN-150CAM bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de AirLive WN-150CAM kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met AirLive WN-150CAM . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
