Gebruiksaanwijzing /service van het product 539 132251 van de fabrikant Dixon
Ga naar pagina of 28
DIXON Blower Kit Collection System 539 132250, 539 132251 539 132252, 539 132397 Operator and Parts Manual.
©2007 HTC. All Rights Reserved. Beatrice, NE. Printed in U.S.A..
CONTENTS SAFETY RULES ............................................................................................................................ 4 CART ON CONTENTS .....................................................................................
4 SAFETY DANGER ! THIS CUTTING MACHINE IS CAP ABLE OF AMPUT A TING HANDS AND FEET AND THROWING OB- JECTS. F AILURE TO OBSER VE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESUL T IN SERI- OUS INJURY OR DEA TH. SAFE OPERA TION PRACTICES FOR RIDE-ON MOWERS I.
5 SAFETY DO NOT • Do not turn on slopes unless necessary , and then, turn slowly and gradually downhill, if possible. • Do not mow near drop-off, ditches, or embankments. The mower could suddenly turn over if a wheel is over the edge of a cliff or ditch, or if an edge caves in.
6 SAFETY CAUTION W ARNING Look for this symbol to point out important safety precautions. It means CAUTION! BECOME ALERT! YOUR SAFETY IS INVOL VED. CAUTION In order to prevent accidental starting when.
7 UNP ACKING INSTRUCTIONS • Remove all parts and packing materials from carton. TOOLS REQUIRED • Drill and 11 / 32 " drill bit - 3 bag system only • 5 / 16 " Wrench or ratchet and sock.
8 ASSEMBL Y 1. Remove the discharge chute from the deck. (Deck con fi guration will vary by size and model) 2. Lower deck to the lowest cutting position. 3. Remove the right hand (discharge side) belt cover from the deck. 4. Relieve the tension from the deck belt and remove from the center deck pulley .
9 ASSEMBL Y 2 MOUNTING BLOWER ASSEMBL Y OUTER PULLEY COVER PIN HAIRPIN COTTER 3 INST ALLING DRIVE BEL T REAR OF DECK IDLER PULLEYS OUTER PULLEY TWIST IN BELT TENSION RELEASE LEVER 1. Install the front and rear mount brackets to the deck with the pin and hairpin cotter supplied with the kit.
10 ASSEMBL Y BELT COVER TAB 4 INST ALLING BEL T COVERS RETAINER KNOB OUTER PULLEY COVER DECK BELT SHIELD MIDDLE CHUTE LATCH DECK BELT SHIELD WING NUT TAP SCREW BELT SHIELD STANDOFF 1. Place deck belt shield over spindle, aligning hole with bolt on belt shield standoff.
11 ASSEMBL Y 5 INST ALLING MIDDLE CHUTE MIDDLE CHUTE BLOWER ASSEMBLY Depending on model, engine guard may have available mounting holes. If drilling is needed, use template supplied with kit. 1. Attach template to engine guard at the corresponding holes as shown in illustration.
12 ASSEMBL Y 7 INST ALLING CHUTE SUPPORT 3 Bin System only 1. Position upper chute support against bagger inlet, fl ush at outer edges. See Illlustration. 2. Using support as a template, drill two 3 / 8 " holes into bagger hood. UPPER CHUTE SUPPORT BAGGER INLET NUT BAGGER HOOD FLAT WASHERS HEX BOLT FLEX TRIM 3.
13 ASSEMBL Y CAUTION DO NOT operate mower with grass catcher , unless the front weights are installed. NOTE: Ram Ultra units do not require a weight kit. 9 MOUNTING COVER ASSEMBL Y TO SUPPORT ASSEMBL Y NOTE: For ease of assembly , you may wish assis- tance from another person for mounting the cover assembly to mower .
14 TIPS FOR IMPROVED BAGGING OPERA TION Follow the mower operation instructions in the mower operator ’s manual. When utilizing the grass catcher on a lawn where grass and leaf bagging equipment has not been used, thatch and debris that has accumulated for long periods of time will be picked up.
15 CUST OMER RESPONSIBILITIES GENERAL RECOMMENDA TIONS Always observe safety rules when performing any maintenance. • Before each use check for loose fasteners. • Clean unit thoroughly after each use. BLADE CARE For best results mower blades must be kept sharp.
16 PA R T S 6 6 5 5 4 4 4 3 3 1 9 2 12 10 7 8 11.
17 PA R T S ITEM P ART NO. QTY . DESCRIPTION ITEM P ART NO. QTY . DESCRIPTION 539 108081 1.. .... 1 .... SCREW , SPEC 10-14 x ½ 539 108082 2.. .... 1 .... BAG DUMP INDICA TOR 539 108083 3.. .... 2 .... SCREW , 10-24 x 1 1 / 8 539 108084 4.. .... 3 ..
18 PA R T S BAG ASSEMBL Y 960 730019 9 4 10 7 6 1 3 8 11 12 2 3 5 12 14 13 16 15 17.
19 PA R T S ITEM P ART NO. QTY . DESCRIPTION ITEM P ART NO. QTY . DESCRIPTION 532 192709 1.. .... 1 .... SCREEN, COVER 532 195373 2.. .... 1 .... COVER 539 976952 3.. .... 6 .... SCREW , #10-24 x 5 / 8 539 108096 4.. .... 2 .... SPRING, RET AINER 539 108097 5.
20 PA R T S 4 5 7 8 9 10 11 13 14 15 16 17 18 19 20 21 22 23 39 26 25 29 30 38 28 24 1 2 3 6 10 12 14 15 23 THIS SIDE TOWARD BEARING 33 34 35 36 31 44 32 37 44 43 46 40 47 48 50 51 52 53 51 42 45 46 2.
21 PA R T S ITEM P ART NO. QTY . DESCRIPTION ITEM P ART NO. QTY . DESCRIPTION 539 101977 1.. .... 1 .... TRACTION SPRING 539 976952 2.. .... 1 .... SCREW 10-24 x .625 RD 539 10441 1 3.. .... 1 .... KNOB W/STUD 539 104763 4.. .... 1 .... RET AINER 5 / 16 “U” TYPE 539 105785 5.
22 PA R T S 1 3 4 5 6 7 8 9 10 11 12 13 15 16 17 21 22 23 24 18 19 20 12 14 12 7 14 13 15 15 19 20 14 18 6 14 25 26 27 29 30 31 32 33 34 28 34 12 35 28 28 6 2 14.
23 PA R T S ITEM P ART NO. QTY . DESCRIPTION ITEM P ART NO. QTY . DESCRIPTION 539 132056 1.. .... 1 .... SHIELD, BEL T , 44" 539 132063 2.. .... 1 .... SHIELD, BEL T , 50" 539 132070 3.. .... 1 .... SHIELD, BEL T , 60" 539 132205 4.. ..
24 PA R T S WEIGHT KIT 44" 1 2 3 4 5.
25 PA R T S ITEM P ART NO. QTY . DESCRIPTION ITEM P ART NO. QTY . DESCRIPTION 539 1 1 1587 1.. .... 1 .... CAST WEIGHT 539 1 14898 2.. .... 2 .... WEIGHT BRACKET 539 976979 3.. .... 8 .... NUT 3 / 8 -16, NYLOC 539 106492 4.. .... 4 .... HCS 3 / 8 -16 x 2¾ 539 991 126 5.
26 PA R T S WEIGHT KIT 50" 1 4 3 2 5.
27 PA R T S ITEM P ART NO. QTY . DESCRIPTION ITEM P ART NO. QTY . DESCRIPTION 539 1 13232 1.. .... 3 .... WEIGHT PLA TE 539 1 14898 2.. .... 2 .... WEIGHT BRACKET 539 976979 3.. .... 8 .... NUT 3 / 8 -16 HEX NYLOC 539 102612 4.. .... 4 .... HCS 3 / 8 -16 x 2¾ GR 5 539 976949 5.
539 132264 R1 12/19/07.
Een belangrijk punt na aankoop van elk apparaat Dixon 539 132251 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Dixon 539 132251 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Dixon 539 132251 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Dixon 539 132251 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Dixon 539 132251 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Dixon 539 132251 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Dixon 539 132251 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Dixon 539 132251 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
