Gebruiksaanwijzing /service van het product 539130212 van de fabrikant Dixon
Ga naar pagina of 27
Operators Manual 539 13021 1 - DCKC 539 130212 - DCRC Models: Please read these instructions carefully and make sure you understand them before using the machine.
4 W ARNING: Engine exhaust, some of its constituent s, and certain vehicle component s con- t ain or emit chemicals known to the St ate of California to cause cancer and birth defects or other reproductive harm. INDEX Operators Guide General Information .
5 SAFETY RULES Safety Procedures 1 - T raining: • Read the Operator ’s manual. If the operator(s) or mechanic(s) can not read English it is the owner ’s responsibility to explain this material to them. • Become familiar with the safe operation of the equipment, operator ’s controls, and safety signs.
6 SAFETY RULES 3 - Operation • Never run an engine in an enclosed area. • Only operate in good light, keeping away from holes and hidden hazards. • Slow down and use extra care on hillsides. Make turns gradually and at slow speed. Do not operate across the sides of slopes.
7 ASSEMBL Y Assembly Instructions T ools Required: Ratchet T orque Wrench 1/2" W rench 1/2" Socket 9/16" W rench 9/16" Socket (2) 3/4" Wrench 3/4" Socket Flat Screw Driver (2) 1” Wrench - open end RAM/RAM MAG 1. Remove clamshell from crate.
8 ASSEMBL Y 10. Lift Clamshell assembly onto (539 1 14781) Mount Bracket, Lower . Position tubes on bottom of clamshell on out side of the tubes on (539 1 14781) Mount Bracket, Lower . 1 1 . Secure with (539 1 19372) Hinge Pin and (539 1 15501) Cotter Pin.
9 ASSEMBL Y FIGURE 3 KODIAK 1. Remove clamshell from crate. 2. Remove two 5/16 x 3/4 carriage bolts from the lower flange of the rear guard on the mower .
10 ASSEMBL Y 5. Attach two (539 1 14812) Linkage, Support to the clamshell assembly as shown in Fig- ure 6. 6. Secure with two (539 100476) 5/8 hex jam nut and two (539 1 15591) 5/8 nyloc hex nut as shown. Do not tighten nuts. 7. Lift Clamshell assembly onto (539 1 14815) Mount Bracket, Lower .
11 ASSEMBL Y FRONT WEIGHTS - RAM 1. Bolt cast weight and two weight brackets to- gether using four bolts (539 106492, 3/8 x 2 3/4”) and four nuts (539 976979, 3/8” nyloc). 2. Slide both weight brackets over the front tube on the frame. Be sure to position in the cen- ter of the frame.
12 ASSEMBL Y FRONT WEIGHTS - KODIAK CAST COUNTERWEIGHT WEIGHT BAR HOLD DOWN FRONT WEIGHT BAR 1. Remove mower foot plate and floor pan. 2. Align weight bar to the front of the frame.
13 OPERA TION Operating the Collection System 1. NEVER USE THE COLLECTION SYSTEM WITHOUT THE BLOWER ASSEMBL Y AND HOSES SECUREL Y A TT ACHED. 2 . Make sure hoses are connected at both ends. Inspect hoses prior to each use. 3. Do not use the unit on slopes greater than 10 degrees.
14 SER VICE AND MAINTENANCE Prevent ative Maintenance Schedule Item Before Every Every Every Each Use 5 Hours 25 Hours 50 Hours Inspect/Clean Poly Mesh X X Check/T ighten Nuts & Bolt s X Check/T i.
15 SER VICE AND MAINTENANCE Caring For Hoses 1. Inspect hoses before each use. If hoses have excessive wear , tears, or punctures, replace immediately . 2. T o prolong the life of the hose, periodically ro- tate hose and turn hose end to end. Refer to Preventative Maintenance Schedule in this manual.
16 SERVICE AND MAINTENANCE PROBLEM POSSIBLE CAUSE CORRECTION Loss of V acuum. 1. Hose or hood inlet clogged. 1. Remove hose and clean inlet. 2. Container full. 2. Inspect and empty . 3. Poly mesh plugged. 3. Clean poly mesh. Unusual vibration 1. Solid object jammed in unit.
17 P ARTS ILLUSTRA TIONS.
18 CLAMSHELL ASSEMBL Y 1 2 3 4 5 6 7 8 9 10 REF . REF . 3.
19 CLAMSHELL ASSEMBL Y 1 .. 539 990629 ... 2 ... HCS 3/8-16 X 2 1/4, GR5 2 .. 539 200282 ... 2 ... NUT , 3/8-16, HAM, NYLOC 3 .. 539 990122 ... 3 ... WASHER, 3/8, SAE 4 ... 539 1 15972 ... 2 ... BUSHING 5 .. 539 990717 ... 1 ... NUT , 5/16-18, NYLOC 6 .
20 CLAMSHELL REAR ASSEMBL Y 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 18 10 10 18 10 12.
21 CLAMSHELL REAR ASSEMBL Y 1 ... 539 1 17967 ... 1 ... REAR FRAME 2 ... 539 1 19396 ... 2 ... STRAP 3 ... 539 1 19367 ... 1 ... HOOK LA TCH 4 ... 539 1 19377 ... 1 ... CLAMSHELL BACK 5 ... 539 1 19458 ... 1 ... STRAP 6 ... 539 1 17543 ... 1 ... CHAMSHELL VENT 7 .
22 CLAMSHELL FRONT ASSEMBL Y 1 2 3 4 5 6 7 8 9 10 11 12 13 14 16 17 18 19 20 21 22 23 21 25 26 27 28 24 25 20 15 19 18 23 18 23 18 18 23 16.
23 CLAMSHELL FRONT ASSEMBL Y 1 ... 539 1 19410 ... 1 ... FRONT FRAME 2 ... 539 1 19409 ... 2 ... STRAP 3 ... 539 1 19368 ... 2 ... STRAP 4 ... 539 1 17986 ... 1 ... LIFT SHAFT 5 ... 539 1 19376 ... 1 ... CLAMSHELL, FRONT 6 ... 539 1 15596 ... 2 ... CLEVIS PIN, 5/16 7 .
24 CLAMSHELL LINKAGE - RAM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 5 10.
25 CLAMSHELL LINKAGE - RAM 1 ... 539 1 16443 ... 1 ... BAR SLEEVE 2 ... 539 1 19372 ... 1 ... HINGE PIN 3 ... 539 1 14781 ... 1 ... BRACKET , MOUNT , LOWER 4 ... 539 1 14783 ... 2 ... LINKAGE, SUPPORT 5 ... 539 1 15501 ... 3 ... HAIR PIN COTTER, 1/8 DIA.
26 CLAMSHELL LINKAGE - KODIAK 1 2 3 4 5 6 7 8 9 10 12 13 14 15 16 17 18 19 11 6 3 10.
27 CLAMSHELL LINKAGE - KODIAK 1 ... 539 1 16443 ... 1 ... BAR SLEEVE 2 ... 539 1 19372 ... 1 ... HINGE PIN 3 ... 539 1 15501 ... 3 ... HAIR PIN COTTER, 1/8 DIA. X 1 3/4 4 ... 539 1 14816 ... 1 ... LINKAGE, LA TCH 5 .. 539 990188 ... 1 ... W ASHER, 5/16, SAE 6 .
WEIGHT KIT - RAM 1 ... 539 1 1 1587 ... 1 ... CAST WEIGHT 2 ... 539 1 14898 ... 2 ... BRACKET , WEIGHT 3 .. 539 106492 ... 4 ... HCS, 3/8-16 X 2 3/4, GR5 4 ... 539 991 126 ... 4 ... HCS, 3/8-16 X 3 3/4, GR5 5 .. 539 976979 ... 8 ... NUT , 3/8-16, NYLOC ITEM P ART NO.
WEIGHT KIT - KODIAK 1 ... 539 1 1 1313 ... 1 ... HOLD DOWN, WEIGHT BAR 2 .. 539 102049 ... 2 ... CLEVIS PIN 3 .. 539 108096 ... 2 ... SPRING RET AINER 4 ... 539 1 14858 ... 1 ... WEIGHT BAR 5 .. 539 990627 ... 4 ... HCS, 5/16-18 X 1 1/4, GR5 6 .. 539 977778 .
Een belangrijk punt na aankoop van elk apparaat Dixon 539130212 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Dixon 539130212 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Dixon 539130212 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Dixon 539130212 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Dixon 539130212 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Dixon 539130212 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Dixon 539130212 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Dixon 539130212 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
