Gebruiksaanwijzing /service van het product 2020 van de fabrikant Dover Finishing Products
Ga naar pagina of 23
2020/2220/2520/2210/2510/2200/2500 1 03.27883.100 INSTALLATION INSTRUCTIONS AND OPERATING MANUAL FIREPLACE 2020/2220/2520/2210/2510/2200/2500.
2020/2220/2520/2210/2510/2200/2500 3 03.27883.100 Table of contents pag e Foreword 1. Introduction ....................................................................................................................... 3 2. Safety ....................
2020/2220/2520/2210/2510/2200/2500 3 03.27883.100 Foreword The Installation Manual and Operators Instructions must accompany this appliance. As well as instructions for installa tion and information about use, you will also find advice concerning safety and maintenance.
2020/2220/2520/2210/2510/2200/2500 4 03.27883.100 3 . Princip l e The Dovre model is designed to provide a fireplace convection system without the need to construct a masonry convec tion chamber. The principle of operation is that the cooler air from the lower part of the room is drawn under the base of the inner cast iron unit.
2020/2220/2520/2210/2510/2200/2500 5 03.27883.100 4 . Installation guideline 4 .1. Preparatory measures The fireplace should be hermetically connected to a well - functioning chimney, suff i- ciently enclosed to keep combustible materials (floor and walls) at a distance, and should be installed in a room with sufficien t ventilation.
2020/2220/2520/2210/2510/2200/2500 6 03.27883.100 The same is true for a cover plate or exhaust hood on top of the chimney. The exhaust hood must not narrow the chimney's outlet and should be designed in a way that wind will not hinder, but promote the smoke flow.
2020/2220/2520/2210/2510/2200/2500 7 03.27883.100 Convection air may be led to arrive from both the room and outside (other room, cellar, exterior) to the bottom side of the fire place. In case convection air is supplied (directly or indirectly) from outside, it may also be useful as a supply of fresh air for combustion.
2020/2220/2520/2210/2510/2200/2500 8 03.27883.100 4 .1.4. Combustible material round the fireplace Within the radiation area of the fireplace Assure a distance of at least 80 cm between the opening of the fireplace and co m- bustible material.
2020/2220/2520/2210/2510/2200/2500 9 03.27883.100 4.2.3. Fitting frame surround The decorative frames, 3 and 4 sides versions are fitted to the applaice after install a- tion.
2020/2220/2520/2210/2510/2200/2500 10 03.27883.100 4.2.4. Assembling the “cold handle” Assemble the different parts of the handle, I.e. a screw M8x50, a wooden handle and a nut, as indicated on the s- ketch. 4.2.5. Electrical connection For protection, the unit must always be connected to power.
2020/2220/2520/2210/2510/2200/2500 11 03.27883.100 4 .3. Installation The appliance is designed to be built into a new or existing chimney breast install a- tion to provide space heating by radiant an convected heat.
2020/2220/2520/2210/2510/2200/2500 12 03.27883.100 4.4. Finishing When the appliance is installed in the right place, its connection with the chi m- ney made airtight, and the masonry mantle completely mounted, all loose parts are installed in the appliance.
2020/2220/2520/2210/2510/2200/2500 13 03.27883.100 Example of fireplace installation within combustible material Fireproof floor Combustible ceiling Opening against eventual pressure buildup Chimney E.
2020/2220/2520/2210/2510/2200/2500 14 03.27883.100 Example of installation in an existante fireplace Existant chimney Extra opening for ventilation firepalce Refractory cement or special connector Ope.
2020/2220/2520/2210/2510/2200/2500 15 03.27883.100 5 . Instructions for use 5.1. Fuel The only suitable fuels for this stove are wood, brown coal briquettes and charcoal (when you u se a coal - basket). No other fuels are allowed to be burnt, as they can inflict serious damage to your stove.
2020/2220/2520/2210/2510/2200/2500 16 03.27883.100 glowing enough, you can put the logs, the charcoal or the brown coal briquettes on the fire. 5.3. Burning wood Always keep the stove doors tightly closed. Never let the doo rs open when the fire is burning.
2020/2220/2520/2210/2510/2200/2500 17 03.27883.100 Before adding some extra coals, u se the shaker grate or the supplied shovel, and shake till the glowing parts fall into the ash plate ; then add the coals. After a few minutes, add some more coals until you can only see the glow of the prev ious filling.
2020/2220/2520/2210/2510/2200/2500 18 03.27883.100 6 . Maintenance It takes only little effort to keep your appliance in good condition. Regularly check whether the sealing cord s till closes the doors tightly enough. Minor paint damage can be touched up with a can of spray paint.
2020/2220/2520/2210/2510/2200/2500 19 03.27883.100 Annex 1: technical data sheet Model 2500 / 2510 / 2520 2510D / 2520/2/3 2200 / 2210 / 2220 / 2020 Nominal heat output 10 kW 10 kW 8 kW (2020: 7 kW) F.
2020/2220/2520/2210/2510/2200/2500 20 03.27883.100 Annex 2 : D imensions 2500 2200.
2020/2220/2520/2210/2510/2200/2500 21 03.27883.100 2220 2210S 2520S 2510S.
2020/2220/2520/2210/2510/2200/2500 22 03.27883.100 2020S 2520S/2/3 2510D.
2020/2220/2520/2210/2510/2200/2500 72 03.27883.100 DOVRE N.V. Tel : +32 (0) 14 65 91 91 Nijverheidsstraat 18 Fax : +32 (0) 14 65 90 09 B - 2381 Weelde E - mail : info@dovre.
Een belangrijk punt na aankoop van elk apparaat Dover Finishing Products 2020 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Dover Finishing Products 2020 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Dover Finishing Products 2020 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Dover Finishing Products 2020 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Dover Finishing Products 2020 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Dover Finishing Products 2020 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Dover Finishing Products 2020 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Dover Finishing Products 2020 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
