Gebruiksaanwijzing /service van het product EC-80320 van de fabrikant EC Line
Ga naar pagina of 48
EC-80320 User ’s Manual - i - The Guide Be sure to have read the manual seriousl y be fore your operation. Neither EC PRINTER nor it s affiliates shall be liable to the purchaser of this product or .
EC-80320 User ’s Manual - ii - T able of contents The Guide ...................................................................................................................... ...........................i Chapter 1 In troducti on ................
EC-80320 User ’s Manual - 1 - Chapter 1 Introduction 1.1 Features EC80320 printer is a kind of high-speed mini thermal printer . It is a high-quality , high-reliability and low-noise POS printer and operated easily , whic h can be widely used in ECR, PC-POS and BANK POS for printing variety of receipt.
EC-80320 User ’s Manual - 2 - Parallel (or serial or USB) Interface positi on Drawer connector Power connector Fig1-2 Back of the printer.
EC-80320 User ’s Manual - 3 - Chapter 2 Connecting Cables 2.1 Unp acking Check each item against the following packing list. If any of these it ems are missing. Please contact your dealer . The interface cable is optional, which will be equipped or cancell ed according the customer ’ s request.
EC-80320 User ’s Manual - 4 - 2. Connect the other end of the cable to the host. T ighten t he connector screws. 3. This printer can carry out a network printing through connecti ng p arallel interface to network print server , which you can use are PS-1206, SX-110 and SX-3100 which have been validated.
EC-80320 User ’s Manual - 5 - 2.3.4 Connecting th e Drawer Cable T urn off the printer and plug the drawer cable into the drawer connector on the back of the printer as shown in Fig2-5. W arning: Don’t connect a telephone line to t he drawer connector; otherwise both the telephone line and the pr inter may be damaged.
EC-80320 User ’s Manual - 6 - 2.4 Connecting the Adapter 1. Make sure the printer ’ s power switch is turned of f. Plug the adapter ’s supply cable as shown below . Connect the adapter to the pow er cord. 2. Make sure the voltage of the electr ical outlet ma tches that of the adapter .
EC-80320 User ’s Manual - 7 - Auto-inst all way Double click the file “Setup.exe” in the driver disc, install driver by the following direct. Hand operated inst alling way 1) The inst alling step s for Windows 2000/XP are as follo w s : 1. Click “S tart” -->"Settings ", select “Pr inters”.
EC-80320 User ’s Manual - 8 - The following condition may cause the printer c an’t cut paper properly in Win200 0/XP (or updated version). 1. You do not setup the driver with the document setup.exe in the CD. Instead, you follow the Windows’ installation guide.
EC-80320 User ’s Manual - 9 - 2.6 Network Settings Please use EC PRINTER network setting softw are NetFinder to set the IP address for EC PRINTER printers, which can be found in the CD or downloaded from EC products web site.
EC-80320 User ’s Manual - 10 - Button description: Exit—Exit from the sof tware Search—Search printers in the same LAN Assign IP—Modify the IP address and other settings for the specified printer .
EC-80320 User ’s Manual - 1 1 - If the printer still can not be found out when the network connection is correct in the same network, Please check whether the network fire wa ll on the PC open or not. If there is fire wall, please close it temporarily , open again after finishing searching and setting a printer completely .
EC-80320 User ’s Manual - 12 - automatically . Please make sure there is a DHCP server in the network, or the printe r can not receive an effective IP address. When to specify static address, uncheck “Use DHCP” and f ill in “IP address”, “Subnet Mask” and “Default Gateway”.
EC-80320 User ’s Manual - 13 - 5) Come out a window o f “Add Port”, enter the IP address reported by the “Setting printer ’s IP address” in the “Printer Name or IP Address” column. T ake IP address “192.168.0.240” for example. “Port Name” is created automatically after finishing filling in IP address.
EC-80320 User ’s Manual - 14 - 8) Return to “Additional Port Info rmation Required”, click “Next”. 9) Come out a window of “Completi ng the Add S tandard TCP/IP Printer Port Wizard”, click “Finish”. 10) In the selection of "Manufacturers/Print ers", click “Have Disk”, and then click “Next”.
EC-80320 User ’s Manual - 15 - 4) Come out a window of “Printer port”, select “S tan dard TCP/IP Port”, click “New port”. 5) Come out a window of “Add S tandard TCP/IP Printer Port Wizard”, click “Next”.
EC-80320 User ’s Manual - 16 - 7) Come out a window of “Port information”, se lect “User-defined” in the “Equipment style”, then click “setting”. Come out a window of “A dditi onal Port Information Required”, select “Custom” in the “Device T ype”, then click “settings”.
EC-80320 User ’s Manual - 17 - 9) Return to “Additional Port Info rmation Required”, click “Next”. 10) Come out a window of “Completing the Add S tandard TCP/IP Printer Port Wizard”, click “Finish”.
EC-80320 User ’s Manual - 18 - 12) Return to “Properties”, make sure the netwo rk port is selected, c lick “Apply”, and then click “Close”.
EC-80320 User ’s Manual - 19 - Chapter 3 Base Control Panel Operations 3.1 Control Panel There are three light indicators and one ke y on the control panel shown as Fig 3-1. 3.1.1 Indicator Indicator Description POWER Indicate whether the printer ’ s power supply is connected or not.
EC-80320 User ’s Manual - 20 - 3.3 HEX DUMP PRINTING This function allows you to check whether t he connection between the pr inter and the host or terminal device works properly or not. The method is that press FEED button and power on the printe r , the ERROR indicator blinks once with two beeps.
EC-80320 User ’s Manual - 21 - 3. Right click”EC80320”, select “Properties”. 4. Click “Printer settings ” in the property page. 5. Check whether the selected port in the “Ports” is matched with the port connecting to the pri nter in practical.
EC-80320 User ’s Manual - 22 - Chapter 4 Install and Replace the Roll Paper The printer can install the p aper conveniently , which should be 80mm width. How to deal with the paper will be explained in det ails in this chapter 4.1 Paper Inst alled S tep s 1.
EC-80320 User ’s Manual - 23 - Note: Paper head should be pulled out by the direction of p aper-input slot, but not the opposite. 3. Pull out a small amount of p aper as shown in Fig 4-3. 4. Put the paper as shown bel ow , and then close the cover .
EC-80320 User ’s Manual - 24 - Chapter 5 Features 5.1 General S pecification Item Description Print method Direct thermal printing Print direction Line printing Paper width 72 mm Print speed 220mm/s.
EC-80320 User ’s Manual - 25 - Electricity: 2.5 A Power consumption operation: 40 W; max: 180 W; standby: 2.9 W Note: Only when the product doesn’t connec t any power sup ply , can it consume zero energy .
EC-80320 User ’s Manual - 26 - Note: “IN” means input to the printer ， “OUT” means output from printer . The signal logical level is TTL level.
EC-80320 User ’s Manual - 27 - 5.2.3 USB Interface Full-speed USB interface of version 2.0. 5.2.4 Drawer Connector The drawer connector on the back of the printe r uses the RJ-1 1 conne ctor , which is shown below .
EC-80320 User ’s Manual - 28 - T able A-3: Drawer connector Pin assignments Pin number Signal Direction 1 Frame GND --- 2 Drawer kick-out drive signal OUT 3 Drawer Open/closed signal IN 4 24VDC OUT .
EC-80320 User ’s Manual - 29 - Chapter6 Troubleshooting and Maintenance 6.1 Maintenance T o prolon g the printer’s life, make sure that the printer is well away from heaters and ot her sources of extreme heat, and the surrounding area is clean, dry , and free of dust.
EC-80320 User ’s Manual - 30 - come out. Rotate the white plastic gear by hand in the direction of arrow to make the cutter return to the normal position wh ich is shown as figure 6-1.
EC-80320 User ’s Manual - 31 - Chapter 7 Control C ommands 7.1 General The commands EC80320 supplies are based on ESC /POS, and are compatible with TM-88III serials.
EC-80320 User ’s Manual - 32 - D L E E O T n R e a l - t i m e s t a t u s t r a n s m i s s i o n * Format: ASCII: DLE EOT n D e c i m a l : 1 6 4 n H e x : 1 0 0 4 n Description: T ransmit the sel.
EC-80320 User ’s Manual - 33 - E S C $ S e t a b s o l u t e p r i n t p o s i t i o n F o r m a t : A S C I I : E S C $ n L n H D e c i m a l : 2 7 3 6 n L n H H e x : 1 B 2 4 n L n H Description: Set the distance from the beginning of the line to the position at which subsequent characters are to be printed.
EC-80320 User ’s Manual - 34 - ESC - Turn underline mode o n/off Format: ASCII: ESC - n D e c i m a l : 2 7 4 5 n H e x : 1 B 2 D n Description: n=0, 48 T urn underline mode off.
EC-80320 User ’s Manual - 35 - E S C D S e t h o r i z o n t a l t a b p o s i t i o n . Format: ASCII : ESC D n1……nk NUL Decimal: 27 68 n1……nk NUL H e x : 1 B 4 4 n 1 … … n k N U L Description: Set the horizontal tab position to the column spec ified by nk from the beginning of the line.
EC-80320 User ’s Manual - 36 - E S C S e t r e l a t i v e p r i n t p o s i t i o n F o r m a t : A S C I I : E S C n L n H D e c i m a l : 2 7 9 2 n L n H H e x : 1 B 5 C n L n H Description: Set the print position at (nL+nH*256)* (horizontal or vertical motion unit) inches from current position; nL,nH=0 ～ 255.
EC-80320 User ’s Manual - 37 - ESC j Print and feed paper conversely Format: ASCII: ESC j n Decimal: 27 106 n H e x : 1 B 6 A n Description: Print the content in the buffer and feed p aper n*vertical unit inch conversely . n=0 ～ 255. Horizontal or vertical motion uni t is specified by GS P command.
EC-80320 User ’s Manual - 38 - Selects the Chinese character mode according n as follows: FS & Set Chinese language mode Format: ASCII: FS & D e c i m a l : 2 8 3 8 H e x : 1 C 2 6 Description: In this mode, the code between 0x81 and 0x ff are printed as Chinese character .
EC-80320 User ’s Manual - 39 - F S S S e t C h i n e s e c h a r a c t e r s p a c i n g F o r m a t : A S C I I : F S S n 1 n 2 Decimal: 28 83 n1 n2 H e x : 1 C 5 3 n 1 n 2 Description: 0 ≤ n1 .
EC-80320 User ’s Manual - 40 - GS BEL n1 n2 Beep for appointm ent Format: ASCII: GS BEL n1 n2 n3 Decimal: 29 7 n1 n2 n3 H e x : 1D: 07 n1 n2 n3 Description: N1 specifies the beeping times, n2 specifies t he length of beeping time and n3 specifies the length of intermission time.
EC-80320 User ’s Manual - 41 - GS * Define downloaded bit image F o r m a t : A S C I I : G S * n 1 n 2 d 1 … d k Decimal: 29 42 n1 n2 d1…dk H e x : 1 D 2 A n 1 n 2 d 1 … d k Description: Define the downloaded bit image in the downloaded graphic area.
EC-80320 User ’s Manual - 42 - G S L S e t l e f t m a r g i n Format: ASCII: GS L nL nH Decimal: 29 76 nL nH H e x : 1 D 4 C n L n H Description: Set the left margin to (nL+nH*256)*(hor izontal or vertical motion unit); nL, nH=0 ～ 255. Horizontal or vertical motion uni t is specified by GS P command.
EC-80320 User ’s Manual - 43 - G S k P r i n t b a r c o d e Format: ASCII : GS k m d1..dk NUL Decimal: 29 107 m d1..dk 0 H e x : 1 D 6 B m d 1 . . d k 0 0 * ASCII: GS k m n d1.
EC-80320 User ’s Manual - 44 - Appendix Commands List Here list the commands supported in t he printer in alphabetical order . Control commands Functions Page BEL Beeper 32 HT Horizontal tab 32 LF P.
EC-80320 User ’s Manual - 45 - FS W T urn quadruple-size mode on/off for Chinese character 40 FS p n m Print NV bit image 40 FS q n Define the NV bit image 40 GS BEL Beep for appointment 40 GS FF Pr.
Manufacturer: EC Printer.
Een belangrijk punt na aankoop van elk apparaat EC Line EC-80320 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen EC Line EC-80320 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens EC Line EC-80320 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding EC Line EC-80320 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over EC Line EC-80320 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van EC Line EC-80320 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de EC Line EC-80320 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met EC Line EC-80320 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
