Gebruiksaanwijzing /service van het product SHC-1700 - Type 1, SHC-1700 - Type 1E, SHC-2100 - Type 1, SHC-2100 - Type 1E, SHC-2400 - Type 1, SHC van de fabrikant Echo
Ga naar pagina of 32
H EDGE C LIPPER O PERA T OR ' S M ANUAL 1 Shaf t Hedge Clipper Operator's Manual MODELS: SHC-1700 - T ype 1 - S/N 001001 & Up SHC-1700 - T ype 1E - S/N 501001 - 504767 SHC-2100 - T ype 1.
2 I NTRODUCTION Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job- dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will find both easy to use and full of helpful operating tips and SAFETY messages.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 3 S AFETY GENERAL DESCRIPTION IMPORTANT See Description and Specification sections for full description and illustration of model variation in power head, and handle type. IMPORTANT The enclosed message provides information necessary for the protection of the unit.
4 This unit is not designed to insulate against hazards associated with the contact of wires carrying electrical current. T o avoid possible injury/death due to electrical shock or other hazards. DO NOT operate unit if any wires W ARNING DANGER (power, telephone, cable, etc.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 5 EQUIPMENT Before operation a complete check of the unit must be performed; - Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed. - Inspect fuel lines, tank and area around carburetor for fuel leaks.
6 PERSONAL CONDITION AND SAFETY EQUIPMENT W ARNING DANGER Hedge Clipper users risk injury to themselves and others if the shaft hedge clipper is used improperly and or safety precautions are not followed. Proper clothing and safety gear must be worn when operating a shaft hedge clipper.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 7 Hot Humid Weather Heavy protective clothing can increase operator fatigue which may lead to heat stroke. Schedule heavy work for early morning or late afternoon hours when temperatures are cooler. 50 FEET (15 METERS) GRIP ST ANCE SAFE OPERA TION Determine Operation Area - Review the area to be trimmed.
8 Operation (HCA) - Never adjust blade angle of HCA while standing. - Only adjust cutting angle with HCA resting flat on the ground, with the engine stop switch in the "STOP" position. - Adjust cutting angle by moving locking lever (A) up. Depress blade indexing lever (B) and change blade angle with rear cutter assembly handle.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 9 To reduce the risk of RSI/CTS, do the following: • Avoid using your wrist in a bent, extended or twisted position. Instead try to maintain a straight wrist position. Also, when grasping, use your whole hand, not just the thumb and index finger.
10 HCA-2400 3 4 6 19 20 3 6 9 3 4 6 7 20 21 22 9 18 8 SHC-1700, 2100 POWERHEAD 14 15 12 10 11 13 16 17 10 11 16 12 15 13 14 23 19 8 8 9 SHC-2400, HCA-2400 POWERHEAD 4 12 5 9 14 19 3 6 20 SHC-2400 SHC-.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 11 1. SAFETY MANUAL - Read and understand this manual before operation. Keep manual in a safe location as a reference for safe operating techniques. 2. OPERATOR'S MANUAL - Read and understand this manual before operation.
12 S PECIFICA TIONS L E D O M1 E P Y T 0 0 7 1 - C H S E 1 E P Y T 0 0 7 1 - C H S 1 E P Y T 0 0 1 2 - C H S E 1 E P Y T 0 0 1 2 - C H S 1 E P Y T 0 0 4 2 - C H S E 1 E P Y T 0 0 4 2 - C H S E 1 E P Y T 0 0 4 2 - A C H h t g n e Lm m 5 3 3 1 ) . n i 5 .
H EDGE C LIPPER O PERA T OR ' S M ANUAL 13 A SSEMBL Y ( HCA-2400, SHC-2100, 2400) SHC-1700 is Factory Assembled in the box. Gear Box/Drive Shaft (SHC-2100, 2400, HCA-2400) Tools Required: 8MM Open End Wrench, Screwdriver Parts Required: Power Head/Drive Shaft Assembly and Gear Box/Blade Assembly.
14 P RE -O PERA TION FUEL Fuel Requirements Gasoline - Use 89 Octane [ ] (mid-grade or higher) gasoline or gasohol known to be good quality. Gasohol may contain up to 10% Ethyl (grain) alcohol or 15% MTBE (methyl tertiary-butyl ether). Gasohol containing methanol (wood alcohol) is NOT approved.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 15 IMPORTANT Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added. IMPORTANT Stored two-stroke fuel may separate. ALWAYS shake fuel con- tainer thoroughly before each use.
16 O PERA TION ( SHC Models) - Before starting the unit, equip yourself and any other person working within the 50 ft. (15 M) Safety Zone with the required Protective Equipment and clothing. - During operation, the complete unit, especially the gear box, drive shaft housing and power head muffler area may become very hot, too hot to touch.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 17 ST ARTING COLD ENGINE W ARNING DANGER Blades should not move at idle. If blades move, readjust carbure- tor according to Carburetor Adjustment instructions in the manual or see your ECHO dealer, otherwise serious personal injury may result.
18 ST ARTING W ARM ENGINE The starting procedure is the same as Cold Start except DO NOT close the choke. NOTE If engine does not start after 4 pulls, use Cold Start Procedure.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 19 STOPPING ENGINE ( SHC UNITS ) 1. Release Throttle . Allow engine to idle for a minute 2. Ignition Switch - STOP. Move ignition switch toggle/slide switch to STOP position. NOTE SHC-1700, 2100 with front handle interlock will automatically shut unit off when released.
20 MAINTENANCE INTER V ALS M AINTENANCE Your ECHO product is designed to provide many hours of trouble free service. Regular scheduled maintenance will help achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an ECHO Service Dealer for maintenance.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 21 AIR FIL TER Level 1. Tools required: Cleaning brush, 1" or 2" medium bristle paint brush. Parts required: (SHC Models) 90008 REPOWER TM AIR & FUEL FILTER KIT. (HCA-2400) 90030 REPOWER TM AIR & FUEL FILTER KIT.
22 SP ARK PLUG Level 2. Tools Required: T-Wrench. Feeler gauge. Preferably a wire gauge. Brush. Parts Required: Spark Plug, Champion CJ-7Y or NGK BPM-7A 1 . Remove spark plug and check for fouling, worn and rounded center electrode. 2 . Clean the plug or replace with a new one.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 23 Spark Arrestor Screen 1 . Remove screen holder and gasket from muffler body. 2 . Clean carbon deposits from screen and muffler components. 3 . Replace screen if it is cracked, plugged or has holes burned through.
24 3 . Use the wooden stick or brush to remove dirt from the cylinder fins. 4 . Remove grass and leaves from the grid between the recoil starter and fuel tank. 5 . When installing the engine cover, be certain the tab of the metal deflector shield is in the slot of the cover.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 25 7 . Check idle speed and reset if necessary. If a tachometer is available, idle speed should be set to the specification found on page 12 "Specifications" of this manual.
26 c. Final setting - Set needle at mid point between lean rich drop-off points. (3) d. Turn 1/8 turn CCW (out) making mixture slightly richer. (4) 3 . High speed adjustment. Adjust HI needle (A) with tachometer to achieve the specifications found on page 12 "Specifications" of this manual.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 27 SHC-1700, 2100, 2400, HCA-2400 Tools required: Grease Gun with Lithium Grease, Rag. Parts required: Lithium Based Grease. 1 . Clean dirt from grease fittings. 2 . Carefully pump grease in each fitting. DO NOT force grease.
28 SHARPENING BLADES Level 1. Tools required: Flat file, Small Screwdriver Parts required: Gear Box gasket, Lithium Based Grease. NOTE Blade sharpening requires removal of blades from the unit. Step by step instruction are included in the Service Manual that apply to your model.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 29 4 . Remove the old starter rope and prepare the new rope by first heating both ends to prevent fraying. 5 . Pass one end of the rope through the opening of the drum and tie a knot. Press knot and end of rope in cavity of drum.
30 H 9 . Install drum. The loop in the spring must engage the slot in the drum. Replace the screw and washer. 1 0 . Hold the rope in the notch (H) and rotate the drum counterclock- wise several turns. 1 1 . Hold the drum to prevent it from rewinding, pull the excess rope taught with the handle and allow to rewind slowly.
H EDGE C LIPPER O PERA T OR ' S M ANUAL 31 3 . Remove accumulation of grease, oil, dirt and debris from exterior of unit. 4 . Perform all periodic lubrication and services that are required.
ECHO, INCORPORA TED 400 O AKWOOD R OAD L AKE Z URICH , IL 60047 DEALER? Call 1-800-432-ECHO ECHO, Incorporated 400 Oakwood Road Lake Zurich, IL 60047 Technical Publications Orders S ER VICING I NFORMA TION P ARTS Genuine ECHO Parts and ECHO REPOWER ™ Parts and Assemblies for your ECHO products are available only from an Authorized ECHO Dealer.
Een belangrijk punt na aankoop van elk apparaat Echo SHC-1700 - Type 1, SHC-1700 - Type 1E, SHC-2100 - Type 1, SHC-2100 - Type 1E, SHC-2400 - Type 1, SHC-2400 - Type 1E, HCA-2400 - Type 1E (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Echo SHC-1700 - Type 1, SHC-1700 - Type 1E, SHC-2100 - Type 1, SHC-2100 - Type 1E, SHC-2400 - Type 1, SHC-2400 - Type 1E, HCA-2400 - Type 1E heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Echo SHC-1700 - Type 1, SHC-1700 - Type 1E, SHC-2100 - Type 1, SHC-2100 - Type 1E, SHC-2400 - Type 1, SHC-2400 - Type 1E, HCA-2400 - Type 1E vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Echo SHC-1700 - Type 1, SHC-1700 - Type 1E, SHC-2100 - Type 1, SHC-2100 - Type 1E, SHC-2400 - Type 1, SHC-2400 - Type 1E, HCA-2400 - Type 1E leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Echo SHC-1700 - Type 1, SHC-1700 - Type 1E, SHC-2100 - Type 1, SHC-2100 - Type 1E, SHC-2400 - Type 1, SHC-2400 - Type 1E, HCA-2400 - Type 1E krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Echo SHC-1700 - Type 1, SHC-1700 - Type 1E, SHC-2100 - Type 1, SHC-2100 - Type 1E, SHC-2400 - Type 1, SHC-2400 - Type 1E, HCA-2400 - Type 1E bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Echo SHC-1700 - Type 1, SHC-1700 - Type 1E, SHC-2100 - Type 1, SHC-2100 - Type 1E, SHC-2400 - Type 1, SHC-2400 - Type 1E, HCA-2400 - Type 1E kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Echo SHC-1700 - Type 1, SHC-1700 - Type 1E, SHC-2100 - Type 1, SHC-2100 - Type 1E, SHC-2400 - Type 1, SHC-2400 - Type 1E, HCA-2400 - Type 1E . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
