Gebruiksaanwijzing /service van het product SRM - 2110 van de fabrikant Echo
Ga naar pagina of 36
Grass T rimmer/Brush Cutter Operator's Manual MODELS, SRM - 2100, 21 10 Serial Number 001001 & Up MODELS, T ype 1E SRM - 2100, 21 10 Serial Number 001001 & Up W ARNING DANGER Read rules for safe operation and instructions carefully. ECHO provides an Operator's Manual and a Safety Manual.
2 I NTRODUCTION Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the- job-dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will find both easy to use and full of helpful operating tips and SAFETY messages.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 3 FRONT HANDLE (LOOP SHOWN) DRIVE SHAFT (W/DECALS) DEBRIS SHIELD (W/DECALS) CUTTING ATTACHMENT (NYLON BLADE SHOWN) STOP SWITCH POWER HEAD (W/DECALS) IMPORTANT The enclosed message provides information necessary for the protection of the unit.
4 SHAFT DECAL W ARNING DANGER • This unit can be dangerous and cause serious injury if improperly used. To reduce injury risk to operator, helpers and bystanders, read and understand the Operator's and Safety manuals. • Blindness can occur from objects that are thrown or ricocheted even with shield in place.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 5 EQUIPMENT Before operation a complete check of the unit must be performed; • Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed. • Inspect fuel lines, tank and area around carburetor for fuel leaks.
6 PERSONAL CONDITION AND SAFETY EQUIPMENT W ARNING DANGER Trimmer/Brush Cutter users risk injury to themselves and others if the trimmer/brush cutter is used improperly and or safety precautions are not followed. Proper clothing and safety gear must be worn when operating a trimmer.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 7 15M (50 ft.) SAFE OPERA TION Determine Operation Area - Provide all operators of this equipment with the operator's manual and instructions for safe operation. - Review the area to be trimmed.
8 Vibration and Cold -- It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals may be brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sensations followed by loss of color and numbness in the fingers.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 9 Contents List Items 1 - Power Head 1 - Drive Shaft Assembly 1 - Plastic Bag (co-pack) - 1, Operator's Manual - 1, Safety Manual - 1.
10 1 SAFETY VIDEO 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 26 EMISSION CONTROL -- The emission control system for this engine is EM (Engine Modification). Emission Control Label located on Engine (EXAMPLE ONLY, information on label varies by FAMILY).
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 11 1. OPERATOR'S MANUAL - Included in plastic bag (co-pack). Read before operation and keep in a safe place for future reference, i.e., operation, maintenance, storage and specifications.
12 S PECIFICA TIONS SRM-2100, 2110 1/1E * Install and use U-Handle when operating any model with blade. L E D O ME 1 / 1 0 0 1 2E 1 / 1 0 1 1 2 h t g n e L ) . n i 9 5 ( m m 0 0 5 1) . n i 9 5 ( m m 0 0 5 1 h t d i W ) . n i 0 . 3 1 ( m m 0 3 3) . n i 6 .
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 13 PLASTIC SHIELD INST ALLA TION (for Nylon Line Operation) Tools Required: Screwdriver. Parts Required: Plastic Shield, Shield Plate, three (3) 5mm x 15mm screws. NOTE The plastic shield is for use with the Nylon Line Head only.
14 BLADE INST ALLA TION All Models. IMPORTANT If non-standard monofilament head, METAL/PLASTIC blade or cultivator etc. is used, THE CARBURETOR MUST BE RE-SET or serious engine damage may occur. See "Carburetor Adjustment" pages 29 - 30 and "Specifications" page 12 of this manual.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 15 Install Harness Clamp NOTE Some models require installation of Harness Clamp. If your unit does not have a clamp, follow these directions. Tools Required: Screwdriver, 8mm x 10mm Open End Wrench.
16 THROTTLE LINKAGE AND IGNITION LEADS Tools Required: 8mm x 10mm open end wrench (all models), 3mm Allen Wrench. 1. Close choke and remove air filter cover. 2. Loosen nut (A) and place threaded end of throttle linkage in bracket slot. Finger tighten nut (A).
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 17 U - HANDLE INST ALLA TION Tools Required : 8mm x 10mm Open End Wrench, Slotted Screw- driver, (3mm Hex Wrench SRM-2100 only.) Parts Required: U-Handle Kit. (SRM-2100) P/N 35130454130 NOTE On model SRM-2110 use Steps 1, 10, 11 and 13 - 17 only.
18 1 1 . Secure throttle linkage and leads to drive shaft with cable clips supplied. 12. Install power head and align gear box, power head and U-handles. Tighten all screws. 1 3 . Place throttle linkage in slot in bracket with one nut (A) and washer on each side of bracket.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 19 Plastic and Nylon Blades Require "Blade Conversion Kit," P/N 99922200410 (metal shield and shoulder harness). Steel/Metal Blades Require "Blade Conversion Kit" PLUS a "U-Handle Kit.
20 8 Tooth Weed/Grass Blade P/N 69600120331 is designed for grass, garden debris and thick weeds. DO NOT use this blade for brush or heavy woody growth, 3/4" in. (19 mm) diameter or larger. Brush/Clearing Blade P/N 69500120331 is designed for cutting brush and woody growth up to 76 mm (3" in.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 21 SM T W T F S 1234 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 R + M 2 3 M (10 FT.) MINIMUM FUEL Fuel Requirements Gasoline - Use 89 Octane [ ] gasoline or gasohol known to be good quality.
22 15M (50 ft.) IMPORTANT Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel stabilizer is added. IMPORTANT Stored two-stroke fuel may separate. ALWAYS shake fuel container thoroughly before each use.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 23 O PERA TION - Provide all operators of this equipment with the Operator's Manual and instructions for safe operation. - Before starting the unit, equip yourself and any other person working within the 15M (50 ft.
24 5 . After engine fires (or five [5] pulls) move choke lever to “Run” position. Hold throttle trigger fully depressed and pull recoil starter handle/rope (D) until engine starts and runs. Release throttle trigger and allow unit to warm up at idle for several minutes.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 2 5 MAINTENANCE INTER V ALS / T N E N O P M O C M E T S Y S E C N A N E T N I A M E R U D E C O R P D ' Q E R L L I K S L E V E L R O Y.
26 AIR FIL TER Level 1. Tools required: Cleaning Brush Parts required: 90008 REPOWER AIR & FUEL FILTER KIT. 1. Close choke (Cold Start Position). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumulated dirt from the air cleaner area.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 27 SP ARK PLUG Level 2. Tools required: Scrench (combination socket wrench and screw driver supplied with unit), Feeler gauge (preferably a wire gauge), Soft metal brush Parts Required: Spark Plug NGK BPMR-7A 1.
28 NOTE The throttle linkage remains assembled to the cover and the spark plug lead and grommet remain installed. 3. Use the wooden stick or brush to remove dirt form cylinder fins. 4. Remove grass and leaves from the grid between the recoil starter and fuel tank.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 29 CARBURETOR ADJUSTMENT Type 1E Emission Models Level 2. Tools required: Slotted Screwdriver w/2 mm blade width, Tachom- eter (ECHO P/N 99051130017) Parts required: None.
30 B A C (1) (3) (4) (2) CARBURETOR ADJUSTMENT Type 1 Non Emission Models Idle Speed Adjustment NOTE If carburetor has limiter caps follow "Carburetor Adjustment" procedures for Type 1E models on previous page.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 31 A B B C LUBRICA TION Level 1. Tools required: 8 mm Open End Wrench, Cross Head Screwdriver, Clean rag Parts Required: Lithium Base Grease. Gear Housing 1. Clean all loose debris from gear box.
32 A B D C E D G E B H F A B 1 . Hold drum (A) and turn spool (B) CW (clockwise) until it stops. Pull spool from drum. DO NOT push in on spool when turning. 2. Use one piece of new nylon line (C) 40 ft. (12m) long and thread through the molded loop (D) on the spool.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 33 SHARPENING MET AL BLADES Three styles of metal blades are approved for use on the ECHO Brush Cutter. The 8-tooth blade can be sharpened during normal mainte- nance. The clearing blade and 80 tooth blade require professional service.
34 Remedy Muffler wet with fuel Engine does not crank No fuel at cylinder Spark at end of plug wire No spark at end of plug wire Spark at plug No spark at plug Engine Cranks Fuel at carburetor No fuel.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANU AL 35 S T ORA GE Long term storage (over 30 days) Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage maintenance which includes the following: 1.
ECHO, INCORPORA TED 400 O AKWOOD R OAD L AKE Z URICH , IL 60047 DEALER? Call 1-800-432-ECHO 1-800-432-(3246) ECHO Incorporated 400 Oakwood Road Lake Zurich, IL 60047 Technical Publications Orders S ER.
Een belangrijk punt na aankoop van elk apparaat Echo SRM - 2110 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Echo SRM - 2110 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Echo SRM - 2110 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Echo SRM - 2110 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Echo SRM - 2110 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Echo SRM - 2110 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Echo SRM - 2110 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Echo SRM - 2110 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
