Gebruiksaanwijzing /service van het product SRM-3800 TYPE1-E van de fabrikant Echo
Ga naar pagina of 21
W ARNING D ANGER READ INSTRUCTIONS CAREFULL Y AND FOLLO W R ULES FOR SAFE OPERA TION. F AILURE T O DO SO COULD RESUL T IN SERIOUS INJUR Y . 847 TRIMMER/ BRUSHCUTTER SRM-3800 TYPE1-E 898696-43132 X7502.
- 1 - INTRODUCTION The ECHO T r immer/Brushcutter , model SRM-3800 TYPE1-E is lightweight, high performance gasoline powered rotary trimmer which is designed for brushcutting, weed control and grass trimming in areas which are difficult to control by any other means .
- 2 - SAFETY INSTRUCTIONS 1. Do Not operate the unit when you are fatigued. 2. Do Not operate if other people or animals are in the work area. 3. Do Not operate the unit without the shield correctly in position. 4. Do Not operate in a confined area. Carbon monoxide exhaust gas is highly poisonous.
- 3 - SRM-3800 TYPE1-E Dimension L × W × H cm (inch) 181.5 × 72 × 46 (71.5 × 28.4 × 18.1) Masses kg (lbs) 8.0 (17.6): without shoulder harness and cutter head Engine T ype Air cooled two stroke single cylinder Displacement mL (cu.
- 4 - ASSEMBLING DRIVE SHAFT • Stand engine uprignt on a lev el floor . • Loosen bolts at drive shaft end of the engine. • Fit drive shaft assembly ensuring that the drive shaft is correctly engaged. • Tignten bolts to fasten driv e shaft assembly .
- 5 - T o eliminate loosening of throttle wire fix it to shaft tube (2 places) and to right hand U-handle (1 place) with wire fixing clips. 1 2 1. Wire fixing clip 2.
- 6 - SHIELD Fit the shield on the gear housing and tighten screws with washers (Seven points) as shown. SHOULDER HARNESS • Fit the shoulder starp to the swivel hook, and adjust the length of starp and or the locaion clamps to maintain the cutter head parallel to the ground.
- 7 - ST AR TING COLD ENGINE • Slide switch to ST AR T/R UN position as shown. • Push purge bulb 3 or 4 times (or until constant flow of fuel is visible in fuel return line.) • Pull choke knob up to COLD ST AR T (Close) position. • Pull recoil star ter until the engine fires.
- 8 - W ARNING D ANGER DO NO T ALLO W EITHER PEOPLE OR ANIMALS INT O THE W ORK AREA. AL W A YS WEAR SAFETY GOGGLES WHEN CUTTING. DRESS PROPERL Y - A V OID LOOSE CLO THING. WHEN GRASS OR WEEDS HA VE CLOGGED THE CUTTER HEAD AFFECTING NORMAL OPERA TION, FIRST , ST OP THE ENGINE AND THEN REMO VE THE DEBRIS.
- 9 - W ARNING D ANGER GRASS/WEED TRIMMERS CAN THRO W GRA VEL, STONE, WOOD CHIPS, GLASS, AND PLASTIC OR MET AL OBJECTS. THE DEBRIS SHIELD BEHIND THE TRIMMER HEAD ST OPS MUCH OF THE DEBRIS, BUT CANNO T PREVENT THE OPERA T OR FROM BEING STRUCK BY SOME DEBRIS.
- 10 - INST ALLA TION OF NYLON LINE HEAD (OPTION) Set the nylon line head to the drive shaft and tighten by turning as shown. CUTTING PROCEDURES SHOULDER HARNESS • Install the harness over the both shoulders and adjust shoulder straps so that the quick release latch rests low on the right hand side.
- 11 - TRIMMING The nylon line will allow you to trim along walls and fence lines. Always try to trim from right to left, walking behind the unit and parallel to the wall or fence, thus deflecting debr is a w ay from the operator .
- 12 - W ARNING D ANGER 1. SERIOUS INJUR Y MA Y RESUL T FR OM THE IMPROPER USE OF STEEL BLADES. READ AND COMPL Y WITH SAFETY INSTRUCTIONS LISTED IN THIS MANU AL. 2. THE EIGHT T OOTH BLADE IS DESIGNED SPECIALL Y T O CUT WEED AND GRASS. T O A V OID INJUR Y DUE T O KICKBA CK OR BLADE FRA CTURE, DO NOT USE THIS BLADE T O CUT BRUSH OR TREES.
- 13 - SHOULDER HARNESS • Install the harness over the both shoulders and adjust shoulder straps so that the quick release latch rests low on the right hand side. • Attach the trimmer/brushcutter to the harness by means of the quick release latch.
- 14 - INST ALLING THE BLADE 1. The installation of the 8 tooth weed/grass blade (option) and the 80 tooth brush is exactly the same. Locking tool Box wrench TIGHTEN 3. Remove the nylon line line head, if fitted, by turning in a clockwise direction. 4 .
- 15 - HEA VY WEED CUTTING • Install the 8 tooth 20 cm (8 inch) blade. (option) • Observing all precautions as listed in this manual, star t the engine and using full throttle, s wing the blade in an arc as y ou move f orward slowly .
- 16 - MAINTENANCE AND CARE - AL W A YS KEEP THE UNIT CLEAN - Air filter Cover AIR FIL TER • Clean before using the unit. - Remove the co ver . (f or air filter and carburetor) - T ake off the air filter . - Brush off dust lightly or wash it in suitable cleaning fluid.
- 17 - High spped needle (H) Low speed needle (L) Idle speed adjustment screw W ARNING D ANGER CUTTING A TT A CHMENT MUST NOT TURN OR MO VE WHEN UNIT IS IDLING.
- 18 - 6. Accelerate to full throttle for 2 - 3 seconds to clear any excess fuel in the engine, then return to idle. Accelerate engine to full throttle to check for smooth transition from idle to high speed. If engine hesitates tur n “L ” needle CCW 1/8 tur n and repeat acceleration.
- 19 - Fuel strainer clogged Clean. Fuel pipe clogged Clean. Suction insufficient Make sufficient. Strainer clogged Clean. Carburetor out of order Disassemble and check. C.D .I. module defectiv e Remove and replace. Ignition coil defective Remove and replace.
- 20 - Improper fuel used Use fuel with correct mixing ratio. Nev er use gasoline of poor quality . Spark plug defective (burnt) Replace. As cooling fins clogged, air Clean fins. does not pass well Excessive deposits in Disassemble and remove carbon. combustion chamber Plug damaged or fouled Replace or clean.
Een belangrijk punt na aankoop van elk apparaat Echo SRM-3800 TYPE1-E (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Echo SRM-3800 TYPE1-E heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Echo SRM-3800 TYPE1-E vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Echo SRM-3800 TYPE1-E leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Echo SRM-3800 TYPE1-E krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Echo SRM-3800 TYPE1-E bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Echo SRM-3800 TYPE1-E kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Echo SRM-3800 TYPE1-E . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
