Gebruiksaanwijzing /service van het product SRM-410U van de fabrikant Echo
Ga naar pagina of 36
Grass T rimmer/Brush Cutter Operator's Manual MODEL SRM-410U X750-012 31 6 X750 216-3706 Printed in Japan 1401Ek 1114 ES W ARNING U sers of this equip men t risk injury to themselves a nd others if the uni t is used im- pr operly and/o r safety p reca utio ns ar e not f ollo wed.
2 Copyright© 2009 By ECHO, Incorporated All Rights Reserved. T ABLE OF C ONTENTS Introduction ..........................................................................2 - The Operator's Manual .................................................2 - The Safety manual .
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 3 INTERNA TIONAL SYMBOLS S AFETY MANUAL SAFETY SYMBOLS AND IMPORT ANT INFORMA TION Throughout this manual and on the product itself, you will fi nd safety alerts and helpful, informational messages pre- ceded by symbols or key words.
4 Physical Condition Y our judgment and physical dexterity may not be good: • if you are tired or sick, • if you are taking medication, • if you have taken alcohol or drugs. Operate unit only if you are physically and mentally well. Eye Protection W ear eye protection that meets ANSI Z87.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 5 DANGER Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death.
6 EQUIPMENT W ARNING Use only ECHO approved attachments. Serious injury may result from the use of a non-approved attachment com- bination. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which have not been tested and approved by ECHO.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 7 P/N 89031749030 P/N X505002310 Hot Decal (near muf fl er) D ESCRIPTION Locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the instruc- tions on them.
8 1. POWER HEAD - Includes the Engine, Clutch, Fuel System, Ignition System and Recoil Starter . 2. THROTTLE TRIGGER LOCKOUT - This lever must be held during starting. Operation of the throttle trigger is prevented unless throttle trigger lockout lever is engaged.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 9 C ONTENTS The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, shield installation and other assembly may be necessary . After opening the carton, check for damage.
10 BLADE INST ALLA TION W ARNING Y ou must install the U-Handle and all Blade Conversion parts shown in the following instructions before operating this unit with a metal blade, otherwise serious injury may result.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 11 1. Align hole in upper plate (D) with notch in gear housing (E), and insert locking tool to prevent splined shaft from turning. Arrow on gear housing fl ange points to notch location. 2.
12 A B C U - HANDLE INST ALLA TION T ools Requir ed : 17 & 19 mm wrench, 4 mm hex socket wrench Parts Requir ed: U-Handle, Clamp w/screws 1. Remove assembling bolt (A) from right hand grip. Install right hand grip (B) onto right hand U-handle (C) until bolt hole in U- handle is visible through bolt hole in bottom of grip.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 13 6. Secure the right hand U-handle by tightening 4 right handle assem- bling bolts (H) loosely . 7. Adjust handles for comfortable operation and tighten handle as- sembling bolt (E) and 4 right handle assembling bolts (H).
14 OPTIONAL NYLON HEAD INST ALLA TION T ools Requir ed: Locking T ool Parts Requir ed: Nylon Line Head. 1. Align hole in upper plate with notch in gear housing, and insert locking tool to prevent splined shaft from turning. 2. Thread line head onto PTO shaft by turning it counter -clockwise until head is tight against upper plate.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 15 2.REPLACING SPOOL NOTE Keep line tight on spool. A. Snap spool into housing while pulling line through eyelets with about 15 cm (6 in) extending out. CAUTION Knob tightens counterclockwise, “left”.
16 O PERA TION W ARNING Moving parts can amputate fi ngers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 17 Plastic/Nylon Grass/W eed Blades may be used where ever the nylon line head is used. DO NOT use this blade for heavy weeds or brush! 8 T ooth G rass and W eed Blade is designed for grass, garden deb ris and thick weeds up to 19 mm (3/4”) dia meter .
18 FUEL NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor performance, or severe engine damage and void the product warranty . Read and follow instructions in the Storage section of this manual.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 19 Mixing Instructions 1. Fill an approved fuel container with half of the required amount of gasoline. 2. Add the proper amount of 2-stroke oil to gasoline. 3. Close container and shake to mix oil with gasoline.
20 ST ARTING COLD ENGINE W ARNING When engine is started, con fi rm that there is not any abnormal vibration or sound. If there is abnormal vibration or sound, ask your DEALER to repair . After refueling tighten fuel cap fi rmly and check for leakage.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 21 ST ARTING W ARM ENGINE 1. Press the decompression device (E). 2. Stop Switch Move stop switch (A) forward away from the STOP position. 3. Pur ge Bulb Pump purge bulb (C) until fuel is visible in the "Clear" fuel return line.
22 M AINTENANCE W ARNING Moving parts can amputate fi ngers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 23 B A AIR FIL TER Level 1. T ools r equired: 25 - 50 mm (1 - 2 in.) cleaning brush Parts r equir ed: REPOWER TM T une-Up Kit NOTE Always brush dirt and debris away from air cleaner area prior to cleaning air fi lter .
24 FUEL FIL TER Level 1. T ools r equired: 200- 250 mm (8 - 10 in.) length of wire with one end bent into a hook, clean rag, funnel, and an approved fuel container . Parts r equir ed: REPOWER TM Tune-Up Kit DANGER Fuel is VER Y fl ammable. Use extreme care when mixing, storing or handling.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 25 COOLING SYSTEM Level 2. T ools r equired: Air compressor and safety nozzle, or: 4 mm Hex wrench, 25 - 50 mm (1 - 2 in.) cleaning brush. Parts Requir ed: None. IMPOR T ANT T o maintain proper engine operating temperatures, cooling air must pass freely through the cylinder fi n area.
26 Exhaust Port Cleaning Level 2. T ools r equired: 4 & 5 mm Hex W rench, W ood or plastic scraper Parts Requir ed: As needed: Heat Shield 1. Remove spark plug lead from spark plug, and remove muf fl er cover (2 screws). 2. Place piston at top dead center .
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 27 IMPOR T ANT If the engine is adjusted for operation above 1 100 feet ASL, the carburetor must be re-adjusted when operating the engine below 1 100 feet ASL, otherwise severe engine damage may result.
28 LUBRICA TION Level 1. T ools Requir ed: 8 & 13 mm Open End W rench, Screwdriver , Clean Rag. Parts Requir ed: POWER BLENDX TM 8 oz. (P/N 91014) or Lithium Base Grease. Gear Housing 1. Clean all loose debris from gear box. 2. Remove the plug (A) and drain screw (B) from the gear case.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 29 SHARPENING MET AL BLADES Three styles of metal blades are approved for use on the ECHO Brush Cutter . The 8-tooth blade can be sharpened during normal mainte- nance. The clearing blade and 80 tooth blade require professional service.
30 DANGER Fuel vapors are extremely fl ammable and may cause fi re and/or explosion. Never test for ignition spark by ground- ing spark plug near cylinder plug hole, otherwise serious personal injury may result.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 31 DANGER Do not store in enclosure where fuel fumes may accumulate or reach an open fl ame or spark. S TORAGE W ARNING During operation the muf fl er or catalytic muf fl er and surrounding cover become hot.
32 S PECIFICA TIONS MODEL ---------------------------------------------------- SRM-410U Length ------------------------------------------------------- 1860 mm (73.2 in.) W idth -------------------------------------------------------- 630 mm (24.8 in.) Height ------------------------------------------------------- 470 mm (18.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 33 W ARRANTY S T A TEMENTS ECHO LIMITED W ARRANTY ST A TEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO'S RESPONSIB.
34 PURCHASED REP AIR P ARTS, SHORT BLOCKS AND ACCESSORIES GDUHVLGHQWLDORUQRQLQFRPHSURGXFLQJZDUUDQW GDFRPPHUFLDOLQVWLWXWLRQDODJUL.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 35 NOTES.
ECHO, INCORPORA TED 400 O AKWOOD R OAD L AKE Z URICH , IL 60047-1564 7-2 SUEHIROCHO 1-CHOME, OHME, T OKYO, 198-8760, JAP AN PHONE: 81-428-32-61 18 F AX: 81-428-32-6145 S05403001001/S05403999999.
Een belangrijk punt na aankoop van elk apparaat Echo SRM-410U (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Echo SRM-410U heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Echo SRM-410U vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Echo SRM-410U leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Echo SRM-410U krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Echo SRM-410U bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Echo SRM-410U kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Echo SRM-410U . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
