Gebruiksaanwijzing /service van het product P43T-A2 van de fabrikant ECS
Ga naar pagina of 52
.
.
Preface Preface Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author .
ii Preface Declaration of Conformity This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: • This device may not cause harmful interference, and • T.
iii T T T T T ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS Preface i Chapter 1 1 Introducing the Motherboard 1 Introduction......................................................................................1 Feature .
iv Integrated Peripherals.......................................................32 Power Management Setup.................................................33 PCI/PnP Setup...................................................................34 PC Health Status.
1 Introducing the Motherboard Chapter 1 Introducing the Motherboard Introduction Thank you for choosing the P43T -A2 motherboard. This motherboard is a high performance, enhanced function motherboard designed to support the LGA775 socket Intel ® Y orkfield/W olfdale processors for high-end business or personal desktop mar- kets.
2 Introducing the Motherboard Feature Processor Chipset • Supports DDR2 800/667 DDR2 SDRAM with Dual-channel architecture • Accommodates four unbuffered DIMMs • Up to 4 GB per DIMM with maximum memory size up to 16 GB Memor y Audio • 5.1 Channel High Definition Audio Codec • ADCs supports 96k/48k/44.
3 Introducing the Motherboard This motherboard supports Ultra DMA bus mastering with transfer rates of 133/ 100/66/33 Mb/s. • One PCI Express x16 slot for Graphics Interface • Three PCI Express x1 slots • T wo 32-bit PCI v2.
4 Introducing the Motherboard Motherboard Components.
5 Introducing the Motherboard T able of Motherboard Components This concludes Chapter 1. The next chapter explains how to install the motherboard. L AB E L C O M P O NE NT S 1 . CP U S ock et LG A 775 s ocke t Int e l ® Y o r k f i e l d/ W o l f da le F am i l y proc es s ors 2.
6 Introducing the Motherboard Memo.
7 Installing the Motherboard Chapter 2 Installing the Motherboard Safety Precautions • Follow these safety precautions when installing the motherboard • Wear a grounding strap attached to a ground.
8 Installing the Motherboard Checking Jumper Settings This section explains how to set jumpers for correct configuration of the motherboard. Setting Jumpers Use the motherboard jumpers to set system configuration options. Jumpers with more than one pin are numbered.
9 Installing the Motherboard Checking Jumper Settings The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled. T o avoid the system instability after clearing CMOS, we recommend users to enter the main BIOS setting page to “Load Default Settings” and then “Save & Exit Setup”.
10 Installing the Motherboard Installing Hardware Installing the Processor Caution: When installing a CPU heatsink and cooling fan make sure that you DO NOT scratch the motherboard or any of the surface-mount resis- tors with the clip of the cooling fan.
11 Installing the Motherboard A. Read and follow the instructions shown on the sticker on the CPU cap. B. Unload the cap · Use thumb & forefinger to hold the lifting tab of the cap. · Lift the cap up and remove the cap completely from the socket.
12 Installing the Motherboard Installing Memory Modules This motherboard accommodates four memory modules. It can support four 240-pin DDR2 800/667. The total memory capacity is 16 GB. DDR2 SDRAM memory module table Y ou must install at least one module in any of the four slots.
13 Installing the Motherboard T able A: DDR2 (memory module) QVL (Qualified V endor List) The following DDR2 800/667/533 memory modules have been tested and qualified for use with this motherboard. Type Size Vendor Module Name 512 MB Samsung PC2-4200U-4444-10-B1 A-data A-DATA/Vitesta DDR2 533 1 GB Kingmax KLBD48F-A8KE4 Apacer 78.
14 Installing the Motherboard Ty pe Size Ven dor Module Name Kingston KVR800D2N5/5 12 1.8V 9905315-019.A02LF Micron MT8HT F6464AY-80ED 4 512 MB Qimonda HYS72 T64000HU -2.5-B A-DATA M2GVD 6G3I41P0U 1E5E AET760UD0 0-30DB97X Aeneon AET760UD0 0-25DC08X AU01GE80 0C5KBGC Apacer 78.
15 Installing the Motherboard The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the motherboard’s features and capabilities.
16 Installing the Motherboard Follow these instructions to install an add-on card: 1 Remove a blanking plate from the system case corresponding to the slot you are going to use. 2 Install the edge connector of the add-on card into the expansion slot. Ensure that the edge connector is correctly seated in the slot.
17 Installing the Motherboard Connecting Optional Devices Refer to the following for information on connecting the motherboard optional devices F_AUDIO: Front Panel Audio header This header allows the user to install auxiliary front-oriented microphone and line- out ports for easier access.
18 Installing the Motherboard F_USB1~4: Front Panel USB headers The motherboard has four USB ports installed on the rear edge I/O port array . Additionally , some computer cases have USB ports at the front of the case. If you have this kind of case, use auxiliary USB connector to connect the front-mounted ports to the motherboard.
19 Installing the Motherboard IDE devices enclose jumpers or switches used to set the IDE device as MASTER or SLA VE. Refer to the IDE device user’s manual. Installing two IDE devices on one cable, ensure that one device is set to MASTER and the other device is set to SLA VE.
20 Installing the Motherboard Refer to the illustration below for proper installation: This motherboard does not support the “Hot-Plug” function. 1 Attach either cable end to the connector on the motherboard. 2 Attach the other cable end to the SA T A hard drive.
21 Installing the Motherboard Connecting I/O Devices The backplane of the motherboard has the following I/O ports: PS2 Mouse Use the upper PS/2 port to connect a PS/2 pointing device. PS2 Keyboard Use the lower PS/2 port to connect a PS/2 keyboard. Serial Port Use the COM port to connect serial devices such as mice or (COM) fax/modems.
22 Installing the Motherboard Connecting Case Components After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following: The A TX 24-pin connector allows you to connect to A TX v2.x power supply .
23 Installing the Motherboard SPK: Internal speaker header 4 Signal 3 GND 2 Key 1 VCC Pin Signal Name A TX12V : A TX 12V Power Connector A TX_POWER: A TX 24-pin Power Connector Pi n Signal Name 4 +12V 3 +12V 2 Ground 1 Ground CASE_F AN: Case cooling F AN Power Connector Pin Signal Name Pin Signal Name 1 +3.
24 Installing the Motherboard Front Panel Header The front panel header (F_P ANEL) provides a standard set of switch and LED headers commonly found on A TX or Micr A TX cases. Refer to the table below for informa- tion: Supporting the reset function requires connecting pin 5 and 7 to a momentary- contact switch that is normally open.
25 Using BIOS Chapter 3 Using BIOS About the Setup Utility The computer uses the latest “American Megatrends Inc. ” BIOS with support for Windows Plug and Play . The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS.
26 Using BIOS Press the delete key to access the BIOS Setup Utility . Enter Select CMOS Setup Utility -- Copyright (C) 1985-2008, American Megatrends, Inc.
27 Using BIOS Date (www mm:dd:yy) Mon 04/28/2008 Standard CMOS Setup This option displays basic information about your system. f SA T A1 Not Detected SA T A2 Not Detected SA T A3 Not Detected SA T A4 .
28 Using BIOS IDE BusMaster (Enabled) This item enables or disables the DMA under DOS mode. W e recommend you to leave this item at the default value. Press <Esc> to return to the main menu setting page.
29 Using BIOS Limit CPUID MaxV al (Disabled) Advanced Setup This page sets up more advanced information about your system. Handle this page with caution. Any changes can affect the operation of your computer . CMOS Setup Utility - Copyright (C) 1985-2008, American Megatrends, Inc.
30 Using BIOS Boot Other Device (Y es) When enabled, the system searches all other possible locations for an operating system if it fails to find one in the devices specified under the First, Second and Third boot devices. Press <Esc> to return to the main menu setting page.
31 Using BIOS Memory Remap Feature (Enabled) This item allows users to enable or disable memory hole remapping. Advanced Chipset Setup This page sets up more advanced information about your system. Handle this page with caution. Any changes can affect the operation of your computer .
32 Using BIOS Onboard SA T A Mode (Enhanced) Onboard AUDIO Function (Enabled) USB Functions (Enabled) On Chip SA T A2 Controller (Enabled) OnBoard LAN Function (Enabled) Use this item to enable or disable the onboard LAN function.
33 Using BIOS Soft-off by PWR-BTTN (Instant off) Under ACPI (Advanced Configuration and Power management Interface) you can create a software power down. In a software power down, the system can be resumed by W ake Up Alarms. This item lets you install a software power down that is con- trolled by the power button on your system.
34 Using BIOS Resume By PS2 KB (S3) (Disabled) This item enables or disables you to allow keyboard activity to awaken the system from S3 mode. Resume By PS2 MS (S3) (Disabled) This item enables or disables you to allow mouse activity to awaken the system from S3 mode.
35 Using BIOS PC Health Status On motherboards support hardware monitoring, this item lets you monitor the parameters for critical voltages, temperatures and fan speeds.
36 Using BIOS System Component Characteristics These items display the monitoring of the overall inboard hardware health events, such as System & CPU temperature, CPU & DIMM voltage, CPU & system fan speed,...etc. Press <Esc> to return to the main menu setting page.
37 Using BIOS Auto Detect DIMM/PCI Clk (Enabled) When this item is enabled, BIOS will disable the clock signal of free DIMM/PCI slots. Spread Spectrum (Enabled) If you enable spread spectrum, it can significantly reduce the EMI (Electro-Magnetic Interference) generated by the system.
38 Using BIOS Supervisor Password (Not Installed) This item indicates whether a supervisor password has been set. If the password has been installed, Installed displays. If not, Not Installed displays. Change Supervisor Password (Press Enter) Y ou can select this option and press <Enter> to access the sub menu.
39 Using BIOS User Password (Not Installed) This item indicates whether a user password has been set. If the password has been installed, Installed displays. If not, Not Installed displays. Change User Password (Press Enter) Y ou can select this option and press <Enter> to access the sub menu.
40 Using BIOS This concludes Chapter 3. Refer to the next chapter for information on the software supplied with the motherboard. Updating the BIOS Y ou can download and install updated BIOS for this motherboard from the manufacturer’s W eb site. New BIOS provides support for new peripherals, improve- ments in performance, or fixes for known bugs.
41 Using the Motherboard Software Chapter 4 Using the Motherboard Software If the opening screen does not appear; double-click the file “setup.exe” in the r oot directory .
42 Using the Motherboard Software Setup T ab Setup Click the Setup button to run the software installation program. Select from the menu which software you want to install. Browse CD Exit The EXIT button closes the Auto Setup window . Application T ab Lists the software utilities that are available on the CD.
43 Using the Motherboard Software 2. Click Next. The following screen appears: 3. Check the box next to the items you want to install. The default options are recom- 4. Click Next run the Installation Wizard. An item installation screen appears: 5. Follow the instructions on the screen to install the items.
44 Using the Motherboard Software Method 1. Run Reboot Setup Windows V ista will block startup programs by default when installing drivers after the system restart. Y ou must select taskbar icon Run Blocked Program and run Reboot Setup to install the next driver, until you finish all drivers installation.
45 Using the Motherboard Software 2. Select Classic View . 3. Set User Account . 4. Select Turn User Account Control on or off and press Continue ..
46 Using the Motherboard Software Manual Installation Insert the CD in the CD-ROM drive and locate the P A TH.DOC file in the root directory . This file contains the information needed to locate the drivers for your motherboard. Look for the chipset and motherboard model; then browse to the directory and path to begin installing the drivers.
Een belangrijk punt na aankoop van elk apparaat ECS P43T-A2 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen ECS P43T-A2 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens ECS P43T-A2 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding ECS P43T-A2 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over ECS P43T-A2 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van ECS P43T-A2 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de ECS P43T-A2 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met ECS P43T-A2 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
