Gebruiksaanwijzing /service van het product AR-6024WG van de fabrikant Edimax Technology
Ga naar pagina of 73
ADSL W ir eless Router AR-6024WG User ’ s Manual.
T able of Content s Specification ---------------------------------------------------------------------------------------------- 3 Package Contents ----------------------------------------------------.
UI Preferences ----------------------------------------------------------------------------- 58 Update Gateway -------------------------------------------------------------------------- 59 User Manage.
Specification ADSL Wireless-g Broadband Router Features ADSL S tandards DMT modulat ion and demodulation T one detection for low power mode ITU 992.1 (G .dmt) Annex A, B, C ITU 992.2 (G .lite) ITU 992.3 AD SL2 (G .dmt.bis) ITU 992.4 AD SL2 (G .lite.
S t atic routin g DHCP Serve r and Clie nt NAPT (Network Address and Port T ranslation) NA T (Network Address T r anslation) ICMP (Intern et Control M essage Protocol) Simultaneous USB and Ethernet op eration IGMP (Intern et Grou p Management Protocol) 802.
Power: Input: 90~120V or 200~24 0V , 50/60Hz Output: 7.5VDC/1.5A OS: Windows 98SE/ 2000/ ME/ XP System Requirement: PII-266 + 32M RA M LED Indication: PWR, ADSL LINK, WLA N, LAN Software Upg rade: Upg.
ADSL Wireless Router 4 Port s LAN Features ADSL S tandards DMT modulat ion and demodulation T one detection for low power mode ITU 992.1 (G .dmt) Annex A, B, C ITU 992.2 (G .lite) ITU 992.3 AD SL2 (G .dmt.bis) ITU 992.4 AD SL2 (G .lite.bis) ITU 992.
NAPT (Network Address and Port T ranslation) NA T (Network Address T r anslation) ICMP (Intern et Control M essage Protocol) Simultaneous USB and Ethernet op eration IGMP (Intern et Grou p Management Protocol) 802.1 1g Wireless Access Point 54Mbps Access Point f or wireless conne ctivity Interoperable with IEEE 802.
Specification Hardware Line Connection: RJ-1 1 (2 wires) RJ-45 (4 port) Co nnection Power: Input: 90~120V or 200~24 0V , 50/60Hz Output: 7.5VDC/1.5A OS: WIN 98SE ; WIN 2000 ； WIN ME ； WIN XP S.
Package Content s ADSL Wireless Router CD-ROM containing Manual Ethernet Cable (CA T .5 UTP S traight-Through) ADSL Cable (S tandard telephone cable) Power Adapter Quick Instal.
4 Port ADSL Wireless Route r Factory Reset button RJ-1 1 A DSL port connect ADSL cable here S plitter (optional and changes depending o n country specification) Power Adapter Power cord connect here R.
4 Port ADSL Wireless Router Label Meaning S tatus Indicates Power Power On Power is on Off Power is off WLAN Wireless LAN Flashing Check wireless device. LAN 1/ LAN 2/ LAN 3/ LAN 4 LAN Link Flashing Flashes when data is being sent or received on the LAN connection.
General Setting Move your cursor as following sequence Start Setting s Control Panel and click Control Panel . Then double-click on the Network Connections In the LAN or High-Speed Internet window , right-click on icon corresponding to your network interface card (NIC) and select Properties .
In the General T ab of the Local Area Connection Properties menu. Highlight Internet Protocol (TCP/IP) under “This connection uses the following items.” by click on it once. Click on the Properties button. Select Obtain an IP Address automatically: by clicking once in the circle.
Release IP & Renew IP , then Check Default Gateway: 192.168.1.1 . Launch your PC web brow ser and enter the URL: http://192.168.1.1 In the User name/Password prompt, please type in Admin/Admin as default.
Please wait for the Home page to appear . 15.
OnePage Setup When working with wide area connections, the fi rst thing you must do is to have the handle of the connection. Once you have th e handle for a Connection you must define the PVC and protocol settings for it. Name: Enter the name of your ISP .
preset amount of time. T he default is 60 seconds. If y ou set the time to 0, the ISDN connection will remain always connected to the ISP . Keep Alive: If mode is LCP , This is the Keep Aliv e timer . If a reply to the LCP echo is not received in this amount if time, the connection is dropped.
Ty p e : There six kinds of method (PPPoE/ PP PoA/ S tatic/ DHCP/ Bridge/ CLIP). S tatic Settings Encapsulation: Select you encapsulation ty pe. (Supplied by your ISP). IP Address: Private IP address for connecting to a local private network (Default: 192.
Ty p e : There six kinds of method (PPPoE/ PP PoA/ S tatic/ DHCP/ Bridge/ CLIP). DHCP Settings Encapsulation: Select you encapsulation ty pe. (Supplied by your ISP). IP Address: Private IP address for connecting to a local private network (Default: 192.
VPI: If instructed to change this, type in the VPI value for the initial connection (using PVC 0). Default = 0 . VCI: If instructed to change this, type in the VC I value for the initial connection (using PVC 0). Default = 0 . QoS: Quality of Service type.
PVC Settings VPI: If instructed to change this, type in the VPI value for the initial connection (using PVC 0). Default = 0 . VCI: If instructed to change this, type in the VC I value for the initial connection (using PVC 0). Default = 0 . QoS: Quality of Service type.
Wireless This page allow you to enable and disable the wireless LAN func tion, create a SSID, and select the channel for wireless communications.. Channel : Select a transmission channel for wirel ess communications.
Advanced Beacon Period: T ype the Beacon Period in the text box. Y ou can specify a value from 0 to 65535. The default Beacon Period is 200. DTIM Pe riod: T ype a DTIM (Delivery T raffic Indica tion Message) Period in the text box. Y ou c an specify a value between 1 and 255.
S t atus Network S tatistics The Ethernet Network S tatistics page shows t he statistics for the Ethernet connection. The DSL Network S tatistics page shows the st atistics for the DSL connection.
The Wireless Network S tatistics page shows t he st atistics for the Wi reless connection. 25.
Connection S tatus The Connection S tatus page shows the st atus of PPP for each PPP interface. 26.
System Log The System Log page shows the event s triggered by the system. 27.
Advanced Setting LAN Setup The following is displayed LAN Setup. DHCP Configuration DHCP stands for Dynamic Host Configuratio n Protocol. It can automatically dispatch related IP settings to any local user configured as a DHCP client. Server On: Enables the DHCP server .
Management IP The Management IP page shows t he ADSL physical layer status. IP Address: Private IP address for connecting to a local private network (Default: 192.168.1.1). Netmask: Netmask for the local private network (Default: 255.255.255.0). Default Gateway: This field is optional.
Firewall/NA T Services Network Address T ranslation (NA T): Is a method of mapping one or more IP addresses and/or IP service ports into different specified values. Firewall: In addition to t he built-in NA T mechanism. Firewall/NA T Services: Select Enable to turn on the Firewall/NA T Service.
W AN Setup The following is displayed W AN Setup. Add New Connection When working with wide area connections, the fi rst thing you must do is to have the handle of the connection. Once you have th e handle for a Connection you must define the PVC and protocol settings for it.
Password: Enter the password provided by your ISP . Idle T imeout: Idle timeout means the router will disconnect after being idle for a preset amount of time. T he default is 60 seconds. If y ou set the time to 0, the ISDN connection will remain always connected to the ISP .
Name: Enter the name of your ISP . This informa tion is for identification purposes only . Ty p e : There six kinds of method (PPPoE/ PP PoA/ S tatic/ DHCP/ Bridge/ CLIP). S tatic Settings Encapsulation: Select you encapsulation ty pe. (Supplied by your ISP).
Name: Enter the name of your ISP . This informa tion is for identification purposes only . Ty p e : There six kinds of method (PPPoE/ PP PoA/ S tatic/ DHCP/ Bridge/ CLIP). DHCP Settings Encapsulation: Select you encapsulation ty pe. (Supplied by your ISP).
Name: Enter the name of your ISP . This informa tion is for identification purposes only . Ty p e : There six kinds of method (PPPoE/ PP PoA/ S tatic/ DHCP/ Bridge/ CLIP). Bridge Settings Encapsulation: Select you encapsulation ty pe. (Supplied by your ISP).
Name: Enter the name of your ISP . This informa tion is for identification purposes only . Ty p e : There six kinds of method (PPPoE/ PP PoA/ S tatic/ DHCP/ Bridge/ CLIP). CLIP Settings IP Address: Private IP address for connecting to a local private network (Default: 192.
Advanced UPnP Universal Plug and Play (UPnP) is a dist ributed, open networking standard that uses TCP/IP for simple peer-to –peer network c onnectivity between devices a UPnP device can dynamically join a network, obtain and IP address, convey is cap abilities and learn about other devices on the network.
Multicast The NSP is capable of proxying for applicat ions that are using multicast IP for accessing V ideo content. This application needs to be run when NA T is enabled. Enable IGMP Multicast: Enable or Disable IGMP Multicast. Apply: Click Apply to save the changes.
LAN Clients The LAN Clients p age allows you to set the configuratio n for the LAN port. New IP Address: Enter the IP Address. Hostname: Enter the Hostname.
W eb Filters The following queries manage t he Content Filtering cap abilities of the NSP . Apply: Click Apply to save the changes. 40.
Bridge Filters The bridge filtering page allo ws users to set the confi guration of IP filtering. Source MAC: When the bridge filtering is enabled , enter the Source MAC address, select Block and click Add . Then all incoming W AN and LAN Ethernet p ackets matched with this source MAC addr ess will be filtered out.
Modem Setup Select ADSL T ransmission Rate. T1413: Full-Rate (ANSI T1.413 Issue 2) with line rate support of up to 8 Mbp s downstream and 832 Kbps up stream. GDMT : Full-Rate (G .dmt, G992.1) with line ra te support of up to 8 Mbp s downstream and 832 Kbps up stream.
S tatic Routing The following queries manage the RIP routing app lication and static routing entries for the NSP . The RIP application su pports both version 1 and 2. New Destination IP: Enter the New Destination IP . Gateway: Enter the IP Address of the Gateway .
Access Control Access Control allows users to define t he outgoing traffic permitted or denied access through the W AN interface. The default is to permit all outgoing traffic.
45.
Apply: Click Apply to save the changes. 46.
Port Forwarding The Port Forwarding page allows the user def ine a port forwarding rule without using the firewall policy database definitions and apply it to the connection.
48.
Choose a connection: Y ou can choose a connection to do this. LAN IP: type your LAN IP . For example 19 2.168.1.2. Apply: Click Apply to save the changes.
Dynamic Routing The following queries manage the RIP routing app lic ation and static routing entries for the NSP . The RIP application su pports both version 1 and 2.
Wireless Security Select a Wireless Security level None: Disable Wireless encryption. WEP: WEP encryption scrambles the dat a trans mitted between the wireless stations and the access points to keep network communications private. It encrypt s unicast and multicast communications in a network.
802.1x: The IEEE 802.1x standards outline enhanced security methods for both the authentication of wirel ess stations and encryption key management. WP A: Wi-Fi Protected Access (WP A) is a s ubset of the IEEE 802.1 1i security specification draft. Key dif ferences between WP A and WEP are user authentication and improved data encryption.
Advanced Security The Advanced Security page provides adv anced rules that can be applied to a particular Connection. Enable DMZ: Enable or Disable DMZ. Enable Remote Web: Allow or deny incoming access to the modems Web p ages remotely . Enable Remote T elnet: Allow or deny incoming access to the modems T elnet Interface remotely .
Wireless Management The Wireless Management page allows your prestige can check the MAC addresses of Wireless stations against a list of allowed or denied MAC addresses. Enable Access List: Enable the Wireless Management by Access List. MAC Address: Enter the MAC Address.
T ools The T ools s ection allows you to save the co nfiguration, restart the gateway , update the gateway firmware, setup user and remote log information and run Ping and Modem tests. Ping T est Packet INternet Groper is protocol that s ends out ICMP echo requests to test whether or not a remote host is reachable.
Remote Log The Router T able page displays routing t abl e and allows the user to manually enter the routing entry . The routing table will disp lay the routing status of Destination, Netmask, Gateway and Interface. The inte rface br0 means the USB interface; Io0 means the loopback interface and ppp1 means the PPP interface.
Modem T est This test can be used to check whether y our Modem is properly connected to the Network. This test may t ake a few seconds to complete. T o perform the test, select your connection from the lis t and press the T est button.
UI Preferences The UI preferences page allows user to set screen size. Apply: Click Apply to save the changes. 58.
Update Gateway T o update your gateway firmware, choose an update image (Kernel/ File system) or configuration file In Select a File, and then click the Update Gateway button. Additionally , you may download your configurat ion file from the system by clicking Get Configuration.
User Management User Management is used to change your User Name or Password. User Name: Default is ‘Admin’. Password: Default is ‘Admin’. Apply: Click Apply to save the changes.
System Commands System commands allow you to carry out basic system actions. Press the button to execute a command. 61.
S t atus The S tatus section allows you to view the S t atus/S tatistics of dif ferent connections and interfaces. System Log The System Log page shows the event s triggered by the system.
DHCP Client s The DHCP Clients page shows the MAC Addre ss, IP Address, Host Name and Lease Ti m e . 63.
Modem S tatus The Modem S tatus page shows the modem st atus and DSL statistics. 64.
Network S tatistics The Ethernet Network S tatistics page shows t he statistics for the Ethernet connection. The DSL Network S tatistics page shows the st atistics for the DSL connection.
The Wireless Network S tatistics page shows t he st atistics for the Wi reless connection. 66.
Connection S tatus The Connection S tatus page shows the st atus of PPP for each PPP interface. 67.
Product Information The Product Information p age shows the produc t information and software versions. 68.
Appendix Country ISP PVC VPI:8 Australia All Internet providers VCI:35 VPI:0 Belgium VCI:33 VPI:0 Canada T elus VCI:35 VPI:8 Cybercity VCI:35 VPI:8 Danmark T iscali VCI:35 VPI:1 1 & 1 Internet DSL.
Country ISP PVC VPI:1 T iscali VCI:32 VPI:1 T -online VCI:32 VPI:1 Anderer Anbieter VCI:32 VPI:8 W annadoo VCI:35 VPI:8 France T iscali VCI:35 VPI:8 ISRAEL KPN PPPoE LLC VCI:48 VPI:8 T elecom Italia V.
Country ISP PVC VPI:8 Eresmas VCI:35 VPI:8 Jazztel VCI:35 VPI:8 Ola Internet VCI:35 VPI:0 Retevision VCI:35 VPI:8 T erra VCI:32 VPI:1 T iscali VCI:32 VPI:8 T elefornica VCI:32 VPI:8 Te l e p a c VCI:35 VPI:1 Uni2 VCI:33 VPI:8 Ya .
Country ISP PVC VPI:0 Hinet VCI:33 VPI:0 T aiwan Seednet VCI:33 VPI:8 Etisalat Classical IP Single User VCI:35 VPI:8 United Arab Emirates Etisalat Classical IP for Business VCI:35 VPI:0 United Kingdom.
Een belangrijk punt na aankoop van elk apparaat Edimax Technology AR-6024WG (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Edimax Technology AR-6024WG heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Edimax Technology AR-6024WG vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Edimax Technology AR-6024WG leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Edimax Technology AR-6024WG krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Edimax Technology AR-6024WG bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Edimax Technology AR-6024WG kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Edimax Technology AR-6024WG . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
